Hisense Party Rocker One Plus Party Speaker User Manual

Hisense Party Rocker One Plus Party Speaker

Read all the safety instructions carefully before use and keep this instruction manual for future reference

Important Safety Instructions

The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to aler t the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Safety

1. Read these instructions – All the safety and operating instructions should be read before this product is operated.

2. Keep these instructions – The safety and operating instructions should be retained for future reference.

3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow all instructions – All operating and use instructions should be followed.

5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

10. Do not defeat the safety purpose of the polarized or grounding plug. A polarize plug has two blades with one wider than the
    other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

11. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.

12. Only use attachments/accessories specified by the manufacturer.

13. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

14. Unplug the apparatus during lightning storms or when unused for long periods of time.

15. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

16. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

17. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus must not be exposed to dripping or splashing and objects filled with liquids, such as vases, must not be placed on apparatus.

18. The mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
    Warning

    • The battery (batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.
    • These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing operating other instructions than that unless contained you arein Avoid qualified foreign to do so. bodies and liquids entering the Do device. not place open e.g. lit candles, on or Do directly not use adjacent any to corrosive the or device. abrasive cleaning the agents. device. These could damage the surface of Please bottom refer or rear the enclosure information for on electrical exterior and operating safety the information apparatus. before installing or sufficient Minimum distance of ventilation is around 5cm; the apparatus for The covering ventilation should not openings be with impeded items by No such as naked newspaper, flame table sources -cloths, such as curtains lighted. candles Batteries should be be placed and recycled on or the disposed apparatus; of as per state of and apparatus local in guidelines; moderate or tropical
    • The climates. marquise back of the king label equipment. is pasted on the bottom or

WARNING

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
If you swallowed think or placed batteries inside any might part of have the been body, and seek used immediate batteries medical away from attention. children. Keep If newthe stop battery using the compartment product does and not keep it close away securely, from product children. The contains remote a control coin/button supplied cell with battery. this If the cause severe coin/button internal cell battery burns is in just swallowed, 2 hours it canand lead to death.’O” Correct Disposal of this product. This -A should marking not be indicates disposed that with this other product To household prevent wastes possible harm throughout to the the EU. environment or disposal, human recycle health it from responsibly uncontrolled to promote waste To the return sustainable your used reuse of device, material please use resources.the return retailer and where collection the product systems was or contact purchased. the safe They can recycle. take this product for environmental The registered Bluetoothtrademarks ” word owned mark by and Bluetooth logos SIG,are Inc. We are the licensee to use such marks. Other respective trademarks and owners. trade names are those of their –

FCC INFORMATION (for US customers)

Warning:
Any approved Changes by or the party modifications re not responsible expressly for to compliance operate the could equipment. void the user’s authority

IC Caution
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.

RF warning for Portable devices:

• The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure condition without restriction.

WARNING: This product can expose you to chemicals including Pb which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov

RF warning for Mobile devices:

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

RED

• Hereby, Hisense International Co., Ltd. declares that the radio equipment type Party Rocker One/Party Rocker One Plus is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://hisense.fr https://hisense.de

UKCA

• Hereby, Hisense International Co., Ltd. declares that the radio equipment type Party Rocker One/Party Rocker One Plus is in compliance with Radio Equipment Regulations 2017. The full text of the EU declaration of conformity is available at the following internet address: https://hisense.co.uk

Operating ambient temperature:0 – 45°C, Storage and transportation ambient temperature: -10 – 60°C, altitude not higher than 5000m(air pressure not less than 45kPa),

WARNING:

• replacement of a battery with an incorrect type may defeat a safeguard ;
• disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting of a battery , may result in an explosion ;
• leaving a battery in an extremely high temperature surrounding environments, such as sunshine, fire , or hot surface may result in an explosion or the leakage of flammable liquid or gas ;
• a battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

CAUTION
Risk of fire or explosion if the battery is replaced by an incorrect type!

Features

Thanks for your purchase of our product. Please read through this manual before making connections and operating this product. Retain this manual for future reference.

• Bluetooth playback
• AUX IN
• FM tuner
• USB slot
• Microphone function
• Guitar function
• Multiple EQ sound effect mode

Package Contents

Product Diagram

Top View

Party Rocker One Port

Rear View

Party Rocker One Port

Connections

Connect Power

Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.

• Insert the AC power cord into a main socket.

AUX IN Socket

This unit has an audio input terminal. You can input the analog stereo audio signals from extra devices such as VCD, CD, VCR, MP3 player, etc. Use the audio cable with a 3.5mm(not supplied) connector to connect the input terminal AUX IN on the rear panel of the unit, and press the button to select AUX IN mode.

AUX OUT Socket

This unit has a AUX OUT jack. You can output the analog stereo audio signals to external devices such as an active speaker. Connect an audio cable (not supplied) to the AUX OUT jack on the rear panel of the unit and the AUX IN jack of the external device, and the unit will output audio automatically to the external device.

MIC Socket

Insert the microphone into the microphone socket on the rear panel and adjust to a low level using the microphone volume knob on the rear panel. Adjust the microphone volume level to your desired level using the microphone volume knob on the rear panel. Now, enjoy the karaoke singing!

GUITAR Socket

Insert the guitar cable into the guitar socket on the rear panel. Now, enjoy yourself!

WIRELESS MICROPHONE CONNECTION (Only for Party Rocker One Plus)

Connecting Microphone

To connect the supplied wireless microphone By default, the wireless microphone comes pre-paired with the speaker at the factory.

1. Load the two Alkaline AA batteries with the correct polarity.
2. Turn on the speaker and supplied wireless microphone successively.
   • Wireless connection will be set up automatically.

Notes:
minutes of inactivity.

• A maximum of two wireless microphones are supported.

To replace wireless microphone batteries Cautions:

• Do not mix batteries (old and new or carbon and alkaline, etc.).
• Remove batteries if they are exhausted or if the microphone is not to be used for a long time.
• Batteries contain chemical substances, they should be disposed of properly.

Low battery prompt

• Indicator blinking red

Connecting

Press the O button on the top panel of the unit to switch on the unit. Press the button on the wireless microphone to switch on the wireless microphone, the indicator on the wireless microphone will blink blue and the wireless microphone pair with the unit automatically, once paired successfully, the indicator on the wireless microphone will keep solid blue. Adjust the microphone volume level to your desired level using the microphone volume knob on the rear panel.

Note: when the battery of the wireless microphone is in low battery state, the indicator on the wireless microphone blinks red and need to replace the old batteries in wireless microphone battery compartment with new ones.

Basic Operation

Standby/ON

• Press the button on the unit to switch the main unit ON ,Press and hold for 2 seconds to OFF.
• Disconnect the main plug from the main socket if you want to switch the unit off completely.
• When there is no input signal from the unit more than 15 minutes, it will switch to Standby mode automatically.

DJ Effect

• Press the DJ button to the select different DJ effect.
• Press the DJ key once to play the current DJ. When you press the DJ continuously within 1 second, cycle to select different DJ sound effects. Press the DJ key for 1 second to start playing the current DJ sound effects after no operation;
• DJ sound effect types: DJ1 cheering sound, DJ2 drum sound, DJ3 alarm sound, DJ4 horn sound, DJ5 disc playing sound.

Select Modes
Press the button on the unit to select the play function BTUSBAUX IN-FM mode.

Adjust the Volume
Press the vOL+/VOL- button on the unit to adjust the volume.

Preset Equalizer
During play, press the EQ button repeatedly to select: ROCK-JAZZ-SAMBA-POP- BALANCE.

Bass settings
Press the BASS button to select BASS ON / BASS OFF.

Adjust the LED light

• Press the button repeatedly to select the LED effect: LED OFF, LED1, LED2, LED3, LED4, LED5.
• Press and hold to switch ON/OFF the strobe light

AUX IN Operation

1. Ensure that the unit is connected to the TV or the other audio devices.
2. Press the button on the unit to select the AUX IN mode.
3. Operate your audio device directly for playback features.
4. Press the VOL+/VOL button to adjust the volume to your desired level.

WIRELESS CHARGING

The party speaker can charge wireless charging compatible phones by placing your phone on top of the wireless charging logo of the party speaker.

Note:

1. The wireless charging can be used for charging the compatible smartphone when the unit is in power on state or standby after 4 hours for AC mode.
2. In order to prolong the service life of the battery, direct wireless charging is not allowed in the battery mode.

Bluetooth Operation

Pair Bluetooth-enabled Devices
The first time you connect your Bluetooth device to this player, you need to pair your device to this playe.

Note:

• The operational range between this player and a Bluetooth device is approximately 8 meters (without any object between the Bluetooth device and the unit).
• Before you connect a Bluetooth device to this unit, ensure you know the device’s capabilities.
• Compatibility with all Bluetooth devices is not guaranteed.
• Any obstacle between this unit and a Bluetooth device can reduce the operational range.
• If the signal strength is weak, your Bluetooth receiver may disconnect, but it will re-enter pairing mode automatically.

1. Press the on the unit to select Bluetooth mode.
2. The word “PAIRING” will be shown on the display screen, the system has entered pairing mode.
3. Activate your Bluetooth device and select the search mode.” Hisense Party Rocker One” or “Hisense Party Rocker One Plus” will appear on your Bluetooth device.
4. Plus” in the pairing list, Select” Hisense Party Rocker One” or ” Hisense Party k system is successfully connected and the word “CONNECTED” will scroll show on the display screen.
5. Begin playing music from the connected Bluetooth device.

To disconnect the Bluetooth function, you can:

• Switch to another function on the unit.
• Disable the Bluetooth function on your device.
• Press and hold the”I” button on the unit.

Tips:

• Enter “0000” for the password if necessary.
• The player will also be disconnected when your device is moved beyond the operational range.
• If you want to reconnect your device to this player, place it within the operational range.
• If the device is moved beyond the operational range, when it is brought back, please check if the device is still connected to the player.
• If the connection is lost, follow the instructions above to pair your device to the player again.

Listen to Music from Bluetooth Device
If your Bluetooth device supports A2DP, play music via your device.

• To pause/resume playback, pres .
• To skip toa track, press .
• Press the VOL+/- button to increase or decrease the volume.

TWS Connection

• This TWs(TRUE WIRELESS STEREO) Bluetooth connection only use between the same two speakers.
• Power on both speakers, press button on the both speakers to switch to Bluetooth mode, press
• TWS button on one of both speakers, the display screen of the speaker scroll display TWs ON, and then scroll display TWS PAIRING, both speakers enter the pairing state automatically, once paired successfully, one scrolls display MASTER on the display of the speaker is configured as the master,the other displays SLAVE on the display of the speaker is configured as the slave.
• Enable your Bluetooth device and make sure it is in searching mode.
• Select “Hisense Party Rocker One” or ” Hisense Party Rocker One Plus” from the list of discovered devices and connect to it.
• The master speaker will act as the left channel during TWS and will receive the Bluetooth signal,the other speaker will act as the right channel to play music.
• Press and hold the TWS button to disconnect the MASTER and the SLAVE speaker connection in TWNS connection mode,the display screen of both speakers scroll display TWS OFF.

USB Operation

1. 1 Insert the USB device and press
   button to select USB mode.

2. Play starts automatically. If play does not start
   automatically, press II button.

   • To skip to the previous/next track, press the K buttons on the unit.
   • To skip to the previous/next folder, press and hold K/I buttons on the unit.

3. In PLAY/PAUSE state, press and holdIl button for 3 seconds to switch among in REPEAT 1/REPEAT ALL/ RANDOM/NORMAL.

Charging from the USB Port
The Charging 5V1A socket is designed for charging mobile devices(e.g. Mp3 player, mobile phone, etc). It supplies 5V DC at a charging current up to 1000mA(1A). In power on mode,Use a USB cable (not included) to connect mobile device to Charging Socket of the unit and the mobile device will start charging.

FM Radio Operation

Press button repeatedly to select the TUNER source. The display will show”TUNER”

TUNING in a Station

Auto Tuning

1. Press and hold Iibutton to start auto-tuning. Press button again to stop the auto-tuning.
2. The searched radio stations will be stored as preset stations.

Note: The search may not stop at a station with a very weak signal.

Manual Tuning
Press and hold ia or i button to start the forward or reverse scanning. The display will show the frequency being searched. Once a station has been found, the scanning will stop automatically to change the frequency until you find the station you want.

Searching for a radio station manually

1. Briefly press the buttons until the optimal reception frequency is reached.
2. Each time the buttons   are pressed, the frequency decreases/increases by 0.05MHz.

Recalling a preset station

1. Press  button to switch between preset station and frequency.
2. Press Dibutton to select your desired preset station.

Battery Charging For Party Speaker

Built-in Battery Charging
Use the AC power cord included) to connect the AC power input socket on the unit to the AC power outlet. the current charging indicator light on the unit will flash during charging when five charging- indicator lights on the unit keep solid light that the battery has been fully charged. Alternatively, connect one terminal of the vehicle DC power adapter (not included) to the DC input socket on the unit and connect the other terminal of the vehicle DC power adapter to the power socket on the vehicle.

• 5 LED white light up=approx. 100% full
• 4 LED white light up=approx. 80% full
• 3 LED white light up=approx. 60% full
• 2 LED white light up=approx. 40% full
• 1 LED white light up=approx. 20% full (indicating charging is needed)

Note: when the battery is low, the unit wil emit a prompt beep. When DC in is connected for charging, the unit can only be charged and cannot be played.

Troubleshooting

To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, review the following before requesting service.

No power

• Ensure that the AC cord is properly connected.
• Ensure that there is power at the AC outlet.
• Press button on the speaker.

I hear buzzing or humming

• Ensure all cables and wires are securely connected.
• Connect a different source device (Blu-ray player, etc) to see if the buzzing persists. If it does not, the problem may be with the original device.
• Connect your device to a different input on the speaker.

I can’t find the Bluetooth name of this unit on my Bluetooth device

• Ensure the Bluetooth function is activated on your Bluetooth device.
• Re-pair the unit with your Bluetooth device.

SPECIFICATIONS

Power supply

Amplifier(Max Audio Power)

Ambient conditions

Radia

System

Bluetooth

Proof-water

Wireless microphone (Only for Party Rocker One Plus)

• 15 hrs battery playtime is only for reference and may vary depending on music content and battery aging after numerous charging and discharging cycles. It’s achievable with a predefined music source, light show switch off, volume level at 7 and BT streaming source. if only powered by the battery, the Power would lower automatically to protect the battery.

References

• Hisense UK | For your home, nothing makes more sense.
• P65Warnings.ca.gov
• Hisense UK | For your home, nothing makes more sense.
• Hisense DE | Innovationen für Ihr Zuhause
• Hisense | Téléviseurs, Réfrigérateurs, Barres de son, Laser TV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>