Shenzhen Typhur Technology T1000 Highly Integrated Module User Manual

: June 5, 2024
: Shenzhen Typhur Technology

Table of Contents

Shenzhen Typhur Technology T1000 Highly Integrated Module
Features
Temperature Limit Ratings
Application/ Tools
Regulatory Notices
FCC Part 15.21 statement
- FCC Part 15.105 statement
Industry Canada (IC) Compliance Statement
End Product Labeling
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shenzhen Typhur Technology T1000 Highly Integrated Module

Features

T1000 is a highly integrated module with low-power dual-band (2.4GHz and 5GHz) Wireless LAN (WLAN) and Bluetooth Low Energy communication.

BLE:

Temperature Limit Ratings

Parameter	Minimum	Maximum	Unit
Storage Temperature	-40	+85	°C
Ambient Operating Temperature	-20	+85	°C

Application/ Tools

Image tool

Download the latest image
Download MTK SP_Flash_Tool to install o PC put the module fixture, and connect USB(Type C) to PC to power on the PUT
Launch “SP_Flash_Tool_Selector_exe_Windows_v1.2120.00.000”
Select scatter file
Select “Format ALL + Download”
Press “Download” to start image programming
It will show a green check in the progress while programming done
Reboot device

Shenzhen-Typhur-Technology-T1000-Highly-Integrated-Module-
FIG-1

Engineering mode

Enter Settings -> About tablet -> Device info
Press “LCM info” 8 times
It will enter Engineer Mode

Shenzhen-Typhur-Technology-T1000-Highly-Integrated-Module-
FIG-2

Regulatory Notices

Federal Communications Commission (FCC) Compliance Statement

FCC Part 15.19 Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.21 statement

WARNING: Any changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

FCC Part 15.105 statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.

Our module is limited to OEM installation in mobile or fixed applications only. And the OEM integrator will be responsible for ensuring that the end- user has no manual instructions to remove or install the module. All other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations need separate approval. We will provide antenna installation requirements if applicable.

Industry Canada (IC) Compliance Statement

CAN ICES-3 (B)/NMB-3(B)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

ISED Canada: This device contains license-exempt transmitter (s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

End Product Labeling

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: