Pure Clean PUCWM23 2-In-1 Compact and Portable Washer and Dryer User Guide

: June 5, 2024
: Pure Clean

Pure Clean PUCWM23 2-In-1 Compact and Portable Washer and Dryer

Pure Clean PUCWM23 2-In-1 Compact and Portable Washer and Dryer-
PRODUCT PARTS IDENTIFICATION

CONTROL PANEL
WATER INLET
PULSATOR
WASH TUB LID
HOUSING
SPIN TUB LID
SPIN TUB
POWER CORD
PLASTIC SPIN MAT
DRAIN HOSE

CHIEF TECHNICAL DATA

__

Model

| __

Rated Wash Capacity

| __

Rated Input Power

| __

Rated Power Source

| Energy Efficiency Grade: 5| Packaging Dimension| __

__

Net/Gross Weight

| __

__

Input Water Pressure Area

MPA

---|---|---|---|---|---|---|---
Wash Cleaning Rate 0.7
__

Wash

| __

Spin

| __

Wash

| __

Spin

| __

Voltage

| __

Frequency

| __

Consume Electricity (KWh/Cycle/KG)

| __

Consume Water (L/Cycle/KG)

| __

__

LengthxWidthxDepth

PUCWM23| __

3.5KG

| __

1.5KG

| __

250W

| __

120W

| __

110V

| __

60 Hz

| __

0.032

| __

36

| __

590x390x675(MM)

| __

11/13KG

| __

0.05~0.3

INSTALLATION

Electrical Connection

The unit is designed to function under the recommended power settings mentioned in the rating label at the back of the washing machine.
The power cord must be plugged into a grounded 3-pin outlet.
If the power cord is damaged, it should be replaced by the manufacturer/distributor or a certified technician.

Connection of Water Inlet Hose

Attach the water inlet hose to the water inlet (Please refer to the Parts
Identification on page). Caution: Please use water BELOW 120°F.
The drain hose should be placed so that the water can drain down without any obstruction.

OPERATION INSTRUCTION

Preparing the Wash

The machine should be placed on a flat surface.
Separate the laundry into different groups like: white clothes, color clothes, delicate clothes, lint-free and etc. Wash the laundry according to the washing guide.
Clothes with worn patches or tears should be mended first.
Empty all pockets and close all fasteners.

Prior to Wash

Remove the plastic spin mat from the spin tub.
Check if wash timer knob is set to position “0” and the selector switch is set to “Wash”.
Ensure that drain hose is placed properly to allow draining.
Insert the power cord into a grounded 3-pin outlet.

To Wash

Place the wash load and detergent in the wash tub.
Set the selector switch to “Wash” mode.
Fill the washing machine with water as recommended in the “Laundry Guide.”
Set the wash timer to the wash period recommended in the laundry guide. Your machine will now wash for the time selected. When the wash period expires, set the selector switch to “Drain” position to discharge the water.

WARNING

When connecting the appliance to a water main, only use new hoses, do not use old hoses.
For washing machines with ventilation openings in the base, ensure that nothing is obstruction the openings.
If the power cord is damaged, it must be replaced by the manufacturer/distributor or a certified technician.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not with the appliance.

To Rinse In The Wash Tub

Set the selector knob to “WASH”mode.
Turn the water tap on.
When the rinse water becomes clear, turn off the water tap.
Set the selector switch to ”Drain” position to discharge the water.

Spin Drying

To open the inner safety lid of spin tub, lift up the outer spin cover, then lift up the safety lid.
Transfer the wash load to spin tub commencing with small articles.
Ensure that the clothes are evenly distributed.
Place the removable spin mat over the load to be dried and push lightly downward. (To contain delicate articles within the spin tub).
Close the inner safety lid, then the spin cover.
Set the spin timer to the time recommended in the laundry guide.
The spin tub will spin for the time selected, then stop (at position”0”).
Caution: Ensure that the spin tub completely stops before reaching in to remove the wash load. Be especially careful of children.
To remove or reposition clothes during the spin dry cycle, open the spin cover and inner lids. In this case, the spin tub will automatically stop as a brake is activated when the spin cover is opened.
To restart, close both lids, if required, reset the spin timer.
If there is any abnormal vibrating during spin-drying, turn off the spin timer and rearrange the clothes inside the spin tub.

Simultaneous Washing and spin Drying

two motors are fitted to cover washing and spin-drying
This setup allows you to do a load of wash and spin dry at the same time.
Set the controls for both wash and spin modes (see TO WASH and SPIN DRYING)

Clearing the tub

First, set the selector knob to “DRAIN” mode.
Lastly, unplug the power cord from the outlet.

LAUNDRY GUIDE

Pure Clean PUCWM23 2-In-1 Compact and Portable Washer and
Dryer-3

CLEANING AFTER USE

Cleaning after use will extend the life of your washing machine. Before cleaning, Make sure the knobs are in the OFF position and disconnect the power cord from the electrical outlet.

POINTS TO REMEMBER

Avoid using excessive amounts of bleach, soap powder or detergent.
Use the amount recommended by the respective manufacturers.
For your safety, ensure that the ground connection is correct.
Never put your hands into the spin tub while it is operation.
When washing, the water temperature should be below 120°F.
This is to prevent the plastic components from becoming deformed.
Do not place the washing machine close to heat-generating products such as gas or electric cookers.
When cleaning the washing machine, use a soft cloth.
This will prevent damages to the surface of the cabinet.
Avoid placing a wet load on the control panel.
Do not place the washing machine outside or in a damp area.

BEFORE YOU CALL FOR SERVICE

There may be times when you suspect your washing machine requires maintenance. Before calling for a service engineer, please check the following points to save unnecessary cost. You may be pleasantly surprised that an apparent malfunction can be easily rectified by following the chart below:
If you washing machine will not start, check whether:

The hose circuit breaker is tripped or a fuse is blown.
The cord if firmly connected to the power point or the power point is not switched on.
Something is preventing the pulsator from rotating.
The wash timer is set.

If the spin dryer does not work, check whether: