Exile Audio S50.4 SHIFT SERIES AMPLIFIERS Owner’s Manual
- June 5, 2024
- Exile Audio
Table of Contents
SHIFT SERIES AMPLIFIERS
OWNER’S MANUAL
MODELS: S50.4 / S110.5 / S60.1 / S100.1 / S150.
WELCOME TO EXILE
Congratulations on purchasing your Exile amplifier. Please read this manual in
order to fully understand how to get the best results from this product and
ensure that all advice on how to look after the product is followed.
Thank you for buying Exile, we hope you enjoy listening to your product as
much as we enjoyed creating it.
ATTENTION
An aftermarket audio amplifier will place an additional load on the vehicle’s
charging system. Most modern vehicles have sufficient capacity in the charging
system as not all of the electrical components of the vehicle will be switched
on at once.
Check the fuse rating of the amplifier and use this as the peak current
requirement. Generally, the continuous current draw will be a third of the
peak current.
FEATURES
The Shift series amplifier offers big power in a compact chassis. This makes
for easy installation in tight spaces without sacrificing any of the output.
Shift amps utilize Class D efficiency and come packed with features to give
you ultimate control over your audio. Whether you’re cruising the streets,
getting muddy, or riding the waves Exile Audio has you covered with Shift
series power amplifiers.
- Compact size with a high power output
- Wired remote bass level controller
- Bass boost frequency and level adjustment
- Adjustable low pass and subsonic filters
- High Efficiency, an energy-saving digital amplifier with a reliable full MOSFET design
SPECIFICATIONS Monoblock
Amplifier Class
Frequency Response:
Total Harmonic Distortion
Signal to Noise Ratio:
Gain Range
Low Pass Crossover Range
Subsonic Crossover Range
Bass Boost 445Hz:
Remote Bass Control| Class D
15 – 220Hz
<1%
70dB (1W)
0.2 – 5V
40 – 220Hz
OFF – 220Hz
0 to +12dB
Yes
---|---
U S60.1
Channels
Into 1 ohm
Into 2 ohm
Power/Ground Wire Size:
Dimensions:| 1
400w x 1
600w x 1
4 Gauge
L: 9.4in (239mm)
W: 5.9in (150mm)
H: 2.3in (58mm)
---|---
S100.1
Channels
Into 1 ohm
Into 2 ohms
Into 4 ohm
Power/Ground
Wire Size:
Dimensions:| 1
1000w x 1
650w x 1
400w x 1
4 Gauge
L: 14.0in (354mm)
W: 5.9in (150mm)
H: 2.3in (58mm)
---|---
S150. 1
Channels
Into 1 ohm
Into 2 ohm
Into 4 ohm
Power/Ground
Wire Size:
Dimensions:| 1
1500w x 1
900w x 1
500w x 1
4 Gauge
L: 17.5in (444mm)
W: 5.9in (150mm)
H: 2.3in (58mm)
---|---
SPECIFICATIONS Multichannel
Amplifier Class D
Frequency Response:
Total Harmonic Distortion
Signal to Noise Ratio:
Gain Range
Low Pass Crossover Range
Subsonic Crossover Range
Bass Boost @ 45Hz:
remote Bass Control| class D
20 – 20kHz
<1%
75dB (1W)
0.2 – 5V
50 – 750Hz
50 – 750Hz
0 to +18dB
NA
---|---
S50.4
Channels
Into 4 ohms
Into 2 ohm
Into 4 ohms Bridged
Power/Ground Wire Size
Dimensions| 4
70w x 4
110w x 4
250w x 2
4 AWG
L: 9.4in (239mm)
W: 5.9in (150mm)
H: 2.3in (58mm)
---|---
S110.5
Channels
Into 4 ohm
Into 2 ohms (Sub CH)
Power/Ground Wire Size
Dimensions| 5
100w x 4
530w x 1
4 AWG
L: 15.0in (383)
W: 5.9in (150mm)
H: 2.3in (58mm)
---|---
CONTROL FUNCTION
S60.1/S100.1/S150.1
-
SPEAKER
Connect speaker/subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground. -
+12V POWER
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery.
Warning: Always protect this power cable by installing a fuse or circuit breaker of the appropriate size within 18″ (45cm) of the battery terminal connection. -
REMOTE TURN ON (REM)
This terminal turns on the amplifier when +12 volts is applied to it. Connect it to the remote turn-on lead of the head unit or signal source. -
GND
Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a good idea to replace the factory ground at this time with a larger cable equal to the new amplifier power cable or larger.
CAUTION: Do not connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. -
LIMIT / PROTECT / PWR
The LIMIT LED (S100.1 / S150.1) will light up when the output is clipped or the amplifier gets overheated. When the limit indicator lights up, the amplifier will hold or reduce the output power to protect the subwoofer and amplifier. Please turn down the volume or cool down the amplifier when this indicator lights up continually.
The red PROTECT LED will light up and will be flashing if there is a fault presented to the amplifier. Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
The green PWR LED will light up when the amplifier is powered on and working correctly.
-
REMOTE
Connect the remote controller to control the Subwoofer amplifier volume from the driver seat location, for ease of adjustment during playing. -
INPUT
These RCA input jacks are for use with source units that have RCA outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high-quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system. -
BASS BOOST / BASS BOOST FREQ
This adjusts the boost level of the bass boost center frequency. It can be adjusted from 0 to 12dB, Combining with bass boost frequency (S150.1), you can accurately match the amplifier performance to woofer response. -
GAIN
The level control will match the sensitivity of the amplifier to the source unit’s signal voltage. The Operating range is 200mV minimum to 5V maximum. This is NOT a volume control! -
PDF
This control is used to select the desired low pass x-over frequency. The frequency can be adjusted from 40Hz to 220Hz. -
SUBSONIC
This control can filter out unwanted low frequencies from 1 0Hz (OFF) to 50Hz. This function will increase the power handling of your woofers. -
BRIDGE IN / BRIDGE OUT
The BRIDGE IN jack receives a signal from the master amplifier when this amplifier is bridged as a slave. DO NOT use input jacks when the amplifier is working as a slave. All the functions will be adjusted by the master amplifier.
The BRIDGE OUT jack sends the bridge signal to another, same Shift-series amplifier in bridging configuration. All the functions will be adjusted by the master amplifier. -
CLIP LIMIT This switch controls the output clip limit on/off. When switched on, the amplifier will control the output level at the clip point and reduce the distortion. This will keep your amplifier at a low distortion at the clipped signal.
-
Q CONTROL
This knob adjusts the bass boost curve. Turning it to the narrow side will make the boosted frequency narrow and sharp, turn it to the wide will extend the boosted frequency range.
S50.4
-
SPEAKER
Connect speaker/subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground. -
+12V POWER
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery.
Warning: Always protect this power cable by installing a fuse or circuit breaker of the appropriate size within 18″ (45cm) of the battery terminal connection. -
REMOTE TURN ON (REM)
This terminal turns on the amplifier when +12 volts is applied to it. Connect it to the remote turn-on lead of the head unit or signal source. -
GND
Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a good idea to replace the factory ground at this time with a larger cable equal to the new amplifier power cable or larger.
CAUTION: Do not connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. -
INPUT
These RCA input jacks are for use with source units that have RCA outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high-quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system. -
INPUT SELECT
This button selects either 2ch or 4ch input mode. When pressed in, the amplifier works in 2CH input, mode, CH-B input will be paralleled to CH-A, CH-B input jack will be a dummy. When pressed out, the amplifier will work in 4CH input mode. -
GAIN
The level control will match the sensitivity of the amplifier to the source unit’s signal voltage. The Operating range is 200mV minimum to 5V maximum. This is NOT a volume control!
-
LPF/FUL/HPF SELECTOR & FREQUENCY ADJUST KNOB
This switch and knob control Low Pass Filter, High Pass, and Full pass functions. When set to LPF, The amplifier will cut off high frequencies and should be used for driving subwoofers. When set to HPF, The amplifier will cut off low frequencies and should be used for driving full-range speakers or tweeters. When set to FULL, the Full range of frequencies is reproduced and outputted to the speakers. In another word, the filters are “OFF”. -
PROTECT / PWR
The red PROTECT LED will light up and will be flashing if there is a fault presented to the amplifier. Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
The green PWR LED will light up when the amplifier is powered on and working correctly. -
INPUT LEVEL
The amplifier has dual input sensitivity differential inputs which will receive either High level (Speaker output) or Low level (RCA) signals from your car stereo’s source unit. When switching to PRE IN, The signal can be delivered to the amplifier using the low-level RCA outputs on the source unit. When switching to SPK IN, The High-Level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using a speaker to RCA adapter (not included). -
AUTO TURN ON
For auto turn on/off mode, there are three options: DC Offset/Rem/Audio.
REM: When auto turns on to REM, please connect the unit REM terminal to the source unit remote terminal with an 18AWG cable. This is the preferred mode.
DC Offset: If the OEM source unit has no REM signal output, you can choose DC Offset (Meanwhile, Input select switch to SPK IN mode), DC Offset can turn on/off amplifier by detecting the 6V DC Offset from the OEM source unit terminal.
AUDIO: Audio mode can turn ON/OFF the amplifier by detecting the audio signal from the source unit. Note: If the volume is too Low, The amp may fail to turn on. Check if the source unit volume is properly set.
S110.5
-
SPEAKER
Connect speaker/subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground. -
+12V POWER
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery.
Warning: Always protect this power cable by installing a fuse or circuit breaker of the appropriate size within 18″ (45cm) of the battery terminal connection. -
REMOTE TURN ON (REM)
This terminal turns on the amplifier when +12 volts is applied to it. Connect it to the remote turn-on lead of the head unit or signal source. -
GND
Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a good idea to replace the factory ground at this time with a larger cable equal to the new amplifier power cable or larger.
CAUTION: Do not connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. -
INPUT
These RCA input jacks are for use with source units that have RCA outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high-quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system. -
INPUT LEVEL
The amplifier has dual input sensitivity differential inputs which will receive either High level (Speaker output) or Low level (RCA) signals from your car stereo’s source unit. When switching to PRE IN, The signal can be delivered to the amplifier using the low-level RCA outputs on the source unit. When switching to SPK IN, The High-Level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using a speaker to RCA adapter (not included). -
AUTO TURN ON
For auto turn on/off mode, there are three options: DC Offset/Rem/Audio.
REM: When auto turns on to REM, please connect the unit REM terminal to the source unit remote terminal with an 18AWG cable. This is the preferred mode.
DC Offset: If the OEM source unit has no REM signal output, you can choose DC Offset (Meanwhile, Input select switch to SPK IN mode), DC Offset can turn on/off amplifier by detecting the 6V DC Offset from the OEM source unit terminal.
AUDIO: Audio mode can turn ON/OFF the amplifier by detecting the audio signal from the source unit. Note: If the volume is too Low, The amp may fail to turn on. Check if the source unit volume is properly set.
-
GAIN
The level control will match the sensitivity of the amplifier to the source unit’s signal voltage. The Operating range is 200mV minimum to 5V maximum. This is NOT a volume control! -
HPF
This control is used to set the HPF crossover frequency for the front amplifier channel. The frequency is adjustable between OFF and 200Hz. -
PROTECT / PWR
The red PROTECT LED will light up and will be flashing if there is a fault presented to the amplifier. Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
The green PWR LED will light up when the amplifier is powered on and working correctly. -
REMOTE
Connect the remote controller to control the Subwoofer amplifier volume from the driver seat location, for ease of adjustment during playing. -
SUBSONIC
This control can filter out the unwanted low frequencies from 1 0Hz (OFF) to 50Hz. This function will increase the power handling of your woofers. -
PDF
This control is used to select the desired low pass x-over frequency. The frequency can be adjusted from 40Hz to 220Hz. -
BASS BOOST
This switch adjusts the boost level of the bass boost center frequency. It can be adjusted from 0 to 6dB to 12dB.
WIRING DIAGRAMS
MONO AMPLIFIER WIRING (ONE WOOFER LOAD)
MONO AMPLIFIER WIRING (TWO WOOFER LOAD)
DUAL AMPLIFIER BRIDGE MODE
ATTENTION
**** When bridging two amplifiers you should use the same model amplifiers.
Please make sure the negative speaker terminal of the two amplifiers is
connected by the same gauge cables as the positive terminal being used.
DO NOT connect any signal cables to the input RCA jacks when bridged as a
slave unit.
All the functions will be disabled on the slave amplifier when bridged. It
will be adjusted by the master amplifier.
Exile Audio Lake Oswego, OR USA
www.exileaudio.com
Designed and Engineered in the USA.
Made in China
LIMITED WARRANTY
Exile warrants this product to be free from defects in material and
workmanship under normal use for a period of one year from the date of
original purchase when purchased from an Authorized Exile Dealer. If the
product is labeled B Stock/Refurbished and purchased from an Authorized Exile
Dealer, it is warranted for 90 days from the date of purchase, regardless of
the place of installation. Should service be necessary under this warranty for
any reason due to manufacturing defect or malfunction during the warranty
period, Exile will replace or repair (at its discretion) the defective
merchandise with equivalent merchandise at no charge. Warranty replacements on
B-Stock merchandise may have cosmetic scratches and blemishes. Discontinued
products may be replaced with more current equivalent products. This warranty
is valid only for the original purchaser and is not extended to owners of the
product subsequent to the original purchaser. Any applicable implied
warranties are limited in duration to a period of the express warranty as
provided herein beginning with the date of the original purchase at retail,
and no warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties,
therefore these exclusions may not apply to you. This warranty gives you
specific legal rights; however, you may have other rights that vary from state
to state. This warranty is only valid within the USA, for warranties outside
of the USA consult the appropriate international distributor.
©2021 Exile Audio. All rights reserved. All logos are Trademarks or Registered
Trademarks of Exile Audio.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>