Indian MOTORCYCLE 2413862 LED Headlight Kit Instruction Manual
- June 4, 2024
- Indian Motorcycle
Table of Contents
**
**
Indian MOTORCYCLE 2413862 LED Headlight Kit
APPLICATION
Verify accessory fitment at
www.indianmotorcycle.com.
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted
for. Please retain these installation instructions for future reference and
parts ordering information.
KIT CONTENTS
NOTICE
XXX = Indian® Motorcycle color code (For example: 266 = Black)
| REF | QTY | PART DESCRIPTION | P/N AVAILABLE SEPARATELY |
|---|---|---|---|
| 1 | 1 | Assembly, Headlight, LED |
Assembly, Headlight, Adaptive LED (Not Shown)
|
2413862
n/a
2| 4| Spring Clip, Headlight| 5341622
TOOLS REQUIRED
- Safety Glasses
- Screwdriver, Slotted
IMPORTANT
Your Indian Motorcycle® LED Headlight Kit is exclusively designed for your
vehicle. Please read the installation instructions thoroughly before
beginning. Installation is easier if the vehicle is clean and free of debris.
For your safety, and to ensure a satisfactory installation, perform all
installation steps correctly in the sequence shown.
INSTALLATION INSTRUCTIONS
VEHICLE PREPARATION
GENERAL
- Ensure motorcycle is parked on a flat surface, kickstand is fully extended, and vehicle is stable prior to installation.
- Turn key or ignition switch to OFF position and remove key.
MODES WITH VEHICLE
For models without nacelle, skip to Accessory Installation section.
BOBBER NACELLE REMOVAL
- Remove six screws A from rear of headlight nacelle. Remove and set aside headlight nacelle B.
ACESSORY INSTALLLATION
HEADLIGHT REMOVAL
MODELS WITH OUT NACELLE
- Remove trim ring screw A. Remove headlight C and trim ring B.
MODELS WITH NACELLE
- Remove two trim ring screws A. Remove headlight C, trim ring B and rubber surround D.
REMOVE HEADLIGHTTRIM RING
- Set headlight on a non-scratching surface.
- Remove and retain four spring clips A from trim ring B and separate headlight C from trim ring B.
INSTALLAED TO TRIM RING
IMPORTANT
Set headlight parts on a soft cloth to prevent scratches to finish.
- Insert new LED Headlight q into retained trim ring B. Align tab on headlight with notch in trim ring as shown in inset.
- Install spring clips 2 one at a time.
- a. Ensure spring clip wires route around headlight locating features on edge of LED light housing 1.
-
b. Using a small tipped tool (such as a standard screwdriver), press spring clip 2 under outer lip of trim ring B. Ensure center of spring clip stays aligned around metal tabs of LED light housing 1.
-
c. Repeat this for all four spring clips w.
INSTALLED LED HIGHLIGHT
Models with and without nacelle
- Plug main headlight connector A into harness connector B. Find single brown wire C and plug into single wire terminal D on headlight. Single black terminal wire E will not be used. Tape wire E to main wire harness or tuck into headlight housing.
- Install headlight assembly:
-
Models with no nacelle
-
a. Pull wiring harness and connectors through headlight housing. Install headlight assembly q onto housing and secure with retained screw A. Torque screw to specification.
TORQUE -
36 in. lbs. (4 Nm)
-
Models with nacelle
-
a. Pull wiring harness and connectors through headlight housing and out opening in back. Install headlight assembly q onto housing and secure with two retained screws A. Ensure rubber trim ring B is installed between bucket and headlight. Torque screws to specification.
TORQUE
73 in. lbs. (8 Nm)
- b. Ensure wires for headlight are secured inside the bucket C or wrapped in the harness wrap D.
VEHICLE REASSEMBLY
NACELLE INSTALLATION
- Install nacelle and brackets in place and secure with six retained screws A in rear of headlight nacelle. Push nacelle up against underside of top triple clamp. Torque screws to specification.
TORQUE
84 in. lbs. (9.5 Nm)
FEED BACK FORM
A feedback form has been created for the installer to provide any comments,
questions or concerns about the installation instructions. The form is
viewable on mobile devices by scanning the QR code or by clicking HERE if
viewing on a PC.