CEOPA CE-70SE 5 Zone Mixing Amplifier User Manual
- June 4, 2024
- CEOPA
Table of Contents
CEOPA CE-70SE 5 Zone Mixing Amplifier
User Manual
Please read this user manual carefully before operation
Performance Feature
- Three MIC input , two AUX input, one AUX output, suit for PA system. 70V,100V line voltage output and 4 Ohm~16Ohm constant resistance (balance)output
- MIC 1 has priority inputand mute function
- Individual volume control for MIC and AUX
- Bass and treble control F ive LE D indicators of level meter, convenient to monitor the working state
- Output short circuit protection and alarm 5 channel portoutput
- This amplifier can be a s mall PA system
User Manual
Please read this user manual carefully before operation
Performance Feature
- Three MiC input, two AUX input, one AUX output, suit for PAsystem.
- 70V,100V ine voltage output and 4 Ohm-160 hm cons tant res is tan ce (balance output
- MIC1 has priority input and mute function
- Individual volume control for MIC and AUx
- Bass and treble control .
- Five LED indicators of level meter, co venient to monitor the working state
- Outputshort circuit protection and alarm
- 5 channel port output
- This amplifier can be a s mall PA system
parameter
Operation Notes
- This equipment has passed the strict inspection, however, you should turn off the power, pull out the power plug when dis cover some following anoma lies in case, and contact the dealer Alf smelled smoke and peculiar smell which set out from the equipment. B.Ifwa ter or any metal immerge or fall into the equipment. CIf the equipment fell or the shell da mage. D.If the power cable damaged. E.If the equipment failed. F.f the equipme nt distorted badly\
- This equipment ntconta ins high voltage components, please donotarbitrarily open, so as notto cause fire or electric shock if need to maintain in, please contact dealer or professionals to handle
- .Do not lay liquid container or metal on the equipment to p, if they fall into the equipment, it may cause fire or electric shock
- Do not fall me tal or fammable object into the ventilation slot, so as not to cause fire or electric s hock. Do not touch the power plug when thun during and fulmination, soas not to cause injury of electric shock.
- Do not lay heavy objecton the equipment top, soas to avoid falling or damage, and even ca use injury to persons or damage to equipment and property, in addition, heavy object falling its elf may cause injury or damage
- 1f found voice distortion situation, please do not operate this equipment for long time, this is also a fault alarmmess age, if use unceasingly, it may ca use overheating and fire.
- To clean equipment please contact with the dealer, if the dust accumulated in the equipment for long time, it may cause fire or damage.
- Lay this equipment on as table location and make a appropriate treatment to prevent falling, otherwise it may cause the equipment nt falling, andcause injury to persons or damage to equipment and property
- Soas to avoid the inner temperature to rise, the equipment should be
- centimeter far from the barrier.
Front panel
- Power switch
- Power indicator
- LED leve l meter
- Tone control
- MIC volume control
- AUX volume control
- MIC1 input
- 5zone volume control
Note: When 5 L E D indicators are light for long time, it means overload distortion. then should turn the volume low till 4 or 5 indicator glinting.
Rear panel
- .MIC2&3 input
- AUX1&2 input
- AUX output
- ~16Ohmoutput
- Zone output
- F use
- AC 220~240V power input
MIC1 has priority input, and MC1 input signal earn restrain other input signal. And the restrain degree can be adjusted by the MUTE on the rear panel, The range from 0 db -35cb above, it will be set on the MAX place before leaving factory
Safety Notes
- Be sure to read these notes before using
- Be sure to comply the most important safety notes of safety symbd and message in the manual content.
- It has electricity in the output port. please operate this equipment under the guidance of professionals.
Installation Notes
- This amplifier is us ed in PA system, should be lay in the good ventilation place, do not lay in the surrounding of high temperature.
- Do not expose the equipment under the rain or the surrounding with water and other liquid, so as not to cause fire orelectric shock.
- Please us e under specifed voltage (AC 200-240V,50,60 Hz)I t maybe cause fire or electric shock when the voltage value higher than the specified.
- Do not cut off or change the power cable, so as not to cause damage, additonal do not let the power cable near the heater, also do notlay the heavy object which include the equipment on the cable. so as notto cause fire or electric shock S.
- After finishing speaker connection, plea se be sure to re cover the protection cover in the output port. because it can reach to 100V output voltage in the output port, so do not touch the these ports, so as notto be electric shock. And these ports can notas the power of other equipments.
- Do not ins tall or lay this equipment on the location of ins tability, such as shaking or ske w of the table, lest equipment flling a nd caus ing injury to pers ons or da mage to equipment tand property.
- 1f the hand is wet plea se do not use han d directly to insert or pull out the power plug, it may cause electric shock.
- If you want to pull out the power r plug be sure to hold the plug do not hold ca ble. when the power cable dama ged, using this equipme nt maybe cause fire or electric shock.
- lf you want to move the equipment, please be sure to pull out the plug from the socket
- Do not block the ventilation place on the equipment shell, otherwise it may cause intemal overhea ting and fire
- Do notins tall this equipment in the place where has humidity. more dust, direct sunlight heater, soot, vapor, otherwise itmay cause fire and ele ctric shock
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>