CITY THEATRICAL 5825 QolorFLEX 4x5A DINrail Dimmer User Guide
- June 4, 2024
- City Theatrical
Table of Contents
CITY THEATRICAL 5825 QolorFLEX 4x5A DINrail Dimmer
FEATURES & COMPONENT IDENTIFICATION
The QolorFLEX 4x5A DINrail Dimmer can control a full 20A of LED tape spread
over four channels of 5A each. It uses constant voltage technology which
ensures consistent full range dimming that is especially important at low end
light levels. The unit mounts to a standard hat section DINrail, and has
terminal blocks for all electrical and data connections.
An easy to read onboard display and four button user interface allow selection
of Modes, DMX addresses, setting quantity of DMX channels, selecting 8 or 16
bit output resolution, setting PWM frequency (500Hz to 30KHz), setting output
dimming curve values for matching the dimming curves of other dimmers in use,
and setting the device’s operating profile. The QolorFLEX 4x5A DINrail Dimmer
is also RDM capable. Both DMX and Standalone Modes are available depending on
your application. The unit requires a separate power supply providing input
voltage of 12-24VDC. The maximum current load per channel is 5A with a maximum
device output of 20A.
The QolorFLEX 4x5A DINrail Dimmer operates perfectly with City Theatrical’s
QolorFLEX LED tape, the LED tape of professionals on Broadway, network
television, and architectural lighting installations.
Mode – Sets the Mode to either DMX (Run 1) or Standalone (Run 2).
Quick Start Instructions:
- Connect the QolorFLEX™ 4x5A DINrail Dimmer to your DMX controller using the D1+, D1-, and Ground terminals on the DMX input/output terminal block. As needed, DMX out connections can be made using the D2+, D2-, and Ground terminals.
- Connect your load to the output channel spring terminals. For single color LED tape with two connection wires, connect the V- (black) wire to any one of the four output channel terminals and the V+ (red) wire to its corresponding terminal. When using multi-color LED Tape, connect as follows: CH1-red, CH2 -green, CH3 -blue, and CH4 fourth color. Note*-The V+ (common) circuit for multicolor tape will be connected to either a black or white wire. To determine which is correct, look at one of the sets of contacts on the tape itself and note which color wire is connected to the one labeled (+). Do not exceed the maximum load capacity of 5A per channel.
- Connect the appropriate power supply providing 12-24VDC to the power input spring terminals. Note*-The size of the power supply must match the tape being used in both voltage and watts. QolorFLEX™ 4x5A DINrail Dimmer’s maximum output power rating is: 240W (12V), and 480W(24V).
Control Interface
Operation:
- Press “Up” to scroll thru menu choices
- Press “Select” to enable )programming
- Use “Up” or “Down” buttons to set values
- Press “Enter” to save value.
The six function menus are:
*Note- To restore factory defaults, press and hold both “Enter” and
“Select” for five seconds until display goes out.
DMX Start Address- (Factory default is 001) Sets the DMX address for the
dimmer.
DMX Channel Qty-** (Factory default is 05)
SETTINGS:
- CH01: DMX addresses 1,2,3,4 = 001
- CH02: DMX addresses, 1,3 =001, 2,4 =002
- CH03: DMX addresses, 1,2 =001, 3 =002, 4 =003
- CH04: DMX addresses, 1 =001, 2 =002, 3 =003,4 =004
To Set for Stand Alone
Set to Stand Alone Mode by pushing “Up” button until “run1” is shown. “run1”
denotes DMX mode. Hit “Enter” button, and “Up” button to select “run2”, which
denotes Stand Alone Mode. Cycle power to unit.
In Stand Alone Mode:
- Run2: = Stand Alone Mode
- Pxxx: = Programs 1 to 31
- b-xx: = Brightness levels 1 to 8
- SPxx: = Speed Levels 1 to 16
- x-xx: = Individual channels @ levels
To change back to DMX Mode, select “run1” and cycle power.
Output Resolution- (Factory default is 16)
Resolution determines the smoothness of the dimming. 8 bit uses 1 DMX channel,
while 16 bit uses 2.
AVAILABLE SETTINGS: 08 or 16
PWM Frequency (Factory default is 05)
PWM frequency is used to tune the dimmer for flicker free operation when used
with high speed cameras. A high PWM value produces the least amount of
flicker. A low PWM value produces better dimming quality. Always perform a
camera test to confirm optimal results
AVAILABLE SETTINGS: 00 thru 30
Values: 00 = 500Hz
01 to 30 = 1kHz to 30kHz
Dimming Curve
The Dimming Curve may be adjusted to affect the rate of rise and fall of the
dimmer. Values less than 1.0 increase the rate, while values greater than 1.0
decrease the rate. (1.0 is linear
AVAILABLE SETTINGS: 0.1 thru 9.9 Device DMX Profiles (Factory default
is 1.1)
DMX Address is 001,CH01
dp1.1
| dp2.1
---|---
Channel 1| For all output
dimming
| For all output
dimming
Channel 2| | For all output
Fine dimming
DMX Address is 001,CH02
dp1.1
|
dp2.1
|
dp3.2
---|---|---
Channel 1| For output 1,3
dimming
| For output 1,3
dimming
| For output 1,3
dimming
Channel 2| For output 2,4
dimming
| For output 1,3
Fine dimming
| For output 2,4
dimming
Channel 3| | For output 2,4
dimming
| For all output
dimming
Channel 4| | For output 2,4
Fine dimming
|
DMX Address is 001,CH03
dp1.1
|
dp2.1
|
dp4.3
|
dp5.3
---|---|---|---
Channel 1| For output 1
dimming
| For output 1
dimming
| For output 1
dimming
| For output 1
dimming
Channel 2| For output 2
dimming
| For output 1
Fine dimming
| For output 2
dimming
| For output 2
dimming
Channel 3| For output 3,4
dimming
| For output 2
dimming
| For output 3,4
dimming
| For output 3,4
dimming
Channel 4| | For output 2
Fine dimming
| For all output
dimming
| For all output
dimming
Channel 5| | For output 3,4
dimming
| For all output
dimming
| Strobe Effects
Channel 6| | For output 3,4
Fine dimming
| |
DMX Address is 001,CH04
dp1.1
|
dp2.1
|
dp5.4
|
dp6.4
---|---|---|---
Channel 1| For output 1
dimming
| For output 1
dimming
| For output 1
dimming
| For output 1
dimming
Channel 2| For output 2
dimming
| For output 1
Fine dimming
| For output 2
dimming
| For output 2
dimming
Channel 3| For output 3
dimming
| For output 2
dimming
| For output 3
dimming
| For output 3
dimming
Channel 4| For output 4
dimming
| For output 2
Fine dimming
| For output 4
dimming
| For output 4
dimming
Channel 5| | For output 3
dimming
| For all output
dimming
| For all output
dimming
Channel 6| | For output 3
Fine dimming
| | Strobe Effects
Channel 7| | For output 4
dimming
| |
Channel 8| | For output 4
Fine dimming
| |
Should the dimmer experience an input voltage issue or output overload the
display will flash repeatedly.
Once the issue is corrected, power cycle to reset the unit.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>