Hernik KIDSFLEX Kidsflex User Manual

: June 3, 2024
: HERNIK

Table of Contents

General information
Safety instructions
Handling and functions of the basic seat
Using the optional accessories
Guarantee
Labeling
Maintenance & product care
Technical characteristics
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

USER MANUAL
Kidsflex
version: 11-2020

General information

1.1 Introduction
You have chosen the car seat „KIDSFLEX“ and get hereby a high-quality product from our house. We would like to thank you for your trust in us. To make sure you find joy with this product and to ensure it helps you to make everyday life easier, we present you this manual. It shows you the correct and simple usage and the necessary care and maintenance. To avoid damage due to operator error and to ensure the best use, please read the following instructions carefully. If you have any questions or problems, please contact your dealer. We wish you a trouble-free use and hope that our product meets your expectations. We reserve the right to make technical changes to the version described in this manual.
Before installing in your car and using it for the first time, please read and follow the installation instructions on pages 4 – 7. Please ensure that the instructions for use remain with the product and are therefore available to everyone who uses the seat. Yours
HENRIK GmbH
1.2 Purpose and indication
The KIDSFLEX was developed for the transport of children with special needs in cars. Children with poor head or trunk control (eg infantile cerebral palsy, muscular dystrophy, hypotension) can be supported in their posture by means of individually positioned thorax pads and special upholstery which ensures safe transportation.
Important optional accessories can be used to address specific needs such as the seat angle or the installation of a stable abduction wedge or a footstool. More in chapter IV.
1.3 Relevant information
The KIDSFLEX car seat for disabled children is built for use on the back seat of a car and requires an existing, functioning 3-point seat belt. The seat can be attached behind the front passenger or behind the driver‘s seat. In addition to the 3-point seat belt of your car, the car seat is equipped with a 5point chest and shoulder belt that offers your child additional support.
1.4 Declaration of conformity
HENRIK GmbH declares in sole responsibility that the car seat “KIDSFLEX” complies with the Essential Requirements (Appendix 1 of Directive 93/42 EEC). The product
is marked with the CE mark according to the above-mentioned directive.
1.5 Warranty
A warranty can only be accepted if the product is used under the specified conditions and for the intended purposes. The manufacturer is not liable for damage caused by components and spare parts which were not approved by the manufacturer.
1.6 Service and repair
Service and repairs on the KIDSLFLEX may only be carried out by specialized dealers. If you have any problems, contact your local dealer. For repairs, you will only receive original spare parts.
1.7 Practical instructions
The car seat will be delivered fully assembled. Upon delivery, the dealer will instruct the user how to use the device by using the manual. The specialist dealer should install together with the user the car seat in the car and if available adjust the Isofix strap or the clamp.
In order to achieve an optimal sitting position, it is necessary to adjust the car seat individually to the circumstances of the child. This should always be done by the dealer.
‚After instruction, the user should carry out all functions as well as installation and removal of the car seat in the presence of the specialist dealer.
1.8 Installation in the car

Place the child seat on the vehicle seat. Make sure that the backrest lies flat against the backrest of the vehicle seat.
Tip! If the headrest of the vehicle seat disturbs, remove it.

1.9 Fixing the child in the car seat

Open the 5-point-belt and make sure that the straps are exposed.
If a swivel adapter is available, rotate the car seat. This makes it easier for you to put the child in the car seat.
Swivel the optional thorax pads out by
pressing the red dots.
Put the child in the car seat.
Close the 5-point belt.
Rotate (if a swivel adapter is available) the car seat back until the locking audibly snaps into place.
Now thread the 3-point seat belt into the belt guide and guide the belt through the open belt guide left/right.
Lay the belt over the child and the car seat and thread it on the other side left/right through the second open belt guide. Snap the seat belt
buckle tongue in the car‘s belt buckle. Make sure that the vehicle belt is not twisted. Otherwise, the full protective effect of the restraint system is not given.

ATTENTION! Instructions on how to correctly adjust the headrest, the belt guide and the ISOFIX can be found later in the user manual under points 3.1, 3.4 und 4.1.

Safety instructions

Before use, the components must be checked for perfect function and condition.
The instructions for use must always be carried in the child’s car seat.
The safety of your child is only guaranteed if the seat is installed correctly and if the child is fixed exactly.
The straps must be laid tight and without twisting.
The 3-point safety belt is to be guided through the provided belt guides and is supposed to surround the seat tightly. Please check:
A) whether the seat belt is securely placed in the belt guide
B) whether the belt buckles are locked correctly
C) that no textiles are impacted
Make sure that no solid objects like pins, belt buckles, etc. are placed between the child and the seat belt. This could lead to injuries in the event of accidents.
Explain to your child how important it is to be well-secured and that the course of the straps does not change. It shouldn’t pull on the straps nor open the belt buckles.
Do not make any changes to the car seat, otherwise, you risk your child’s safety.
The car seat must not be damaged by moving parts in the car or through doors.
Never leave your child alone in the child’s car seat.
Inform your passengers how your child can be taken out of the seat after an accident.
After an accident, the entire child’s car seat has to be renewed.

Handling and functions of the basic seat

3.1 Adjusting the headrest

Loosen the cap nut on the back plate.
Adjust the headrest to the desired height.
Fix the cap nuts again.

3.2 Adjusting the seat depth

Lose the seat cushion from the Velcro to get access to the cap nuts.
Open the two cap nuts on the sea plate.
The position of the seat depth plate can now be adjusted to the desired seat depth.
Screw the two cap nuts tight and attach the seat cushion again with the Velcro.

3.3 Adjusting the angle of the back

Open the two quick-release levers on the left and right of the child’s car seat.
Put the back plate to the desired angle and close the levers.

3.3 Adjusting the shoulder and lap belts

Press the red button and pull the lock arts out of the lock.
The individual parts of the belt must be exposed.
Put your child in the car seat.
Make sure that your child sits at the very back of the seat.
Now close the 5-point belt buckle.
Pull the lap belt and both shoulder belts tight.
Close and open the strap again to check that the straps are tight.
Correct the belt length if your child is wearing different clothes.

3.4 Adjusting the belt guide

Loosen the two cap nuts on the back plate at the front so that the screws can be opened.
Adjust the belt guide in the grid, so that you reach the desired position.
Now tighten the screws again and fix the nuts on the back plate at the front.

Using the optional accessories

4.1 ISOFIX adapter
Installation: Hernik KIDSFLEX Kidsflex - adapter

Let the installation of the seat and it‘s adjustment be demonstrated to you by the technician.
Open the setscrews on the left and right and pull the bracket out to the rear.
Adjust the backrest of the car seat to the required angle. Slide the ISOFIX adapter on both sides backward in the direction of the backrest until you hear the locking of the two ISOFIX tongues in the vehicle‘s ISOFIX mounting two klicks).
Push the car seat towards the backrest of the vehicle until both touches and are slightly under tension. This prevents vibrations while driving.
Close the two setscrews left and right. In addition, the two ISOFIX tongues must be protected against unattempt opening, which is why both screws must be tightened.
Ensure that both ISOFIX tongues are engaged by a double-sided pulling test.

Hernik KIDSFLEX Kidsflex - head rest 5 Removal Note:

Open the two screws
Move them forwards in the direction of the car seat, releasing the grid connection of the system. It may be necessary to compensate for the pressure of the padding of the seat so that the connection can be solved.
The car seat can now be removed from the vehicle.

4.2 Clamp bow
Installation:

Let the installation of the seat and adjustment of it be shown to you during the delivery.
Open the setscrews on the left and right and pull the bracket to the rear.
Adjust the backrest of the car‘s seat to the required angle. Now push the clamp on both sides backward in the direction of the backrest, until it sinks into the gap of the car seat and seat upholstery and remains firm.
Push the car seat against the backrest of the vehicle until it rests flat.
Now close the two setscrews left and right.

ATTENTION! Whether the crank of the bracket has to be directed upwards or downwards depends on the construction of the respective car seats.
Removal Note:

Pull the car seat including the clamp out of the gap of the car seat.
4.3 Security tray
Installation:
Let the installation of the security tray be shown to you during the delivery.
Put the security tray on the car seat after sitting your child in it and strapping it on.
Secure the padding using the supplied Velcro straps, which are fastened to the back of the car seat.
Your child’s arms should rest on the table, which leads to an upright seating position. This supports the upper body.
Make sure that no objects are placed on the upholstery which could be dangerous during a braking maneuver.

4.4 Lateral supports

Open the screws of the pads on the back of the back plate.
Position the pads in the desired slots.
Fix the screws again.

4.5 Abduction block

The abduction wedge helps your child to reach a predetermined distance between the knees. In order to loosen or tighten the 5point belt, the wedge must be removed. Open the clamp and remove the wedge upwards.
The wedge should always be used while driving (if chosen as an option), otherwise, your child could be injured by the bracket.
The lever can be changed in its position by gently pulling it forward without moving the screw connection. Make sure it is up and not out of the way, otherwise your child’s calves may come into contact with it.

4.6 Angular adjustment

If the seat angle provided by the vehicle seat is insufficient, the seat angle of the car seat can be increased by the (extended) child seat angle adjustment. For this purpose, the screw left and right has to be opened and another hole to be selected. Then tighten the screws back.
For safety reasons, no quick release is possible here!

4.7 Footrest/foot roll

The tabs are fixed below the seat in the base mount, using grub screws. This is also, how the depth can be adjusted.
The inclination of the handrails can be varied by opening the quick-release lever. Please make sure that the levers are then in a position that does not lead to injury.
To adjust the height of the footrest, open the grub screws on the left and right. Now the height can be changed seamlessly and the grub screws tightened again.

4.8 Swivel

To facilitate the daily transfer to the vehicle, we recommend our swivel adapter, which allows the car seat to swivel outwards by 90°. For technical reasons, only ONE direction of rotation is possible. For a later change in the other direction, the car seat must be converted by HENRIK or an authorized specialist.
The use of the ISOFIX adapter or clamp bow is strongly recommended!
To rotate the chair, pull the snapper up and move the chair at the same time. The optional footrest remains in place to avoid collisions with the front passenger seat and the B-pillar. Pay attention to your child‘s legs as you turn!
After the transfer, simply turn the KIDSFLEX back to the starting position and pay attention to the „click“-sound, when the stainless steel tongue locks in the snapper again.

4.9 Protection mat

Position the protection mat on the car seat without blocking the ISOFIX connectors.
Place the KIDSFLEX in the center of the protective mat and secure it as described in chapter 4.1.

4.10 Belts to connect the chest straps

Position the belt at the height of your child‘s chest. Keep a sufficient distance to the neck!
To prevent the belt from slipping, the inside is equipped with Velcro. To loosen it, loosen it with your fingers.
Now adjust the weight of the belt by threading the belt out of the slider and then widening the belt lock accordingly.
Now secure the loose end of the belt again using the slider to prevent the belt from loosening unintentionally.

Guarantee

Henrik products are designed and manufactured in accordance with strict quality standards. If in exceptional circumstances, you have cause for complaint, Henrik GmbH guarantees in accordance with the terms and conditions of delivery:

24 months warranty on all solid parts, from the date of delivery.
12 months warranty on all moving parts, from the date of delivery.

For parts that were not manufactured by Henrik GMBH, please refer to the warranty policy of the respective manufacturer (Römer-Britax Kindersicherheit GmbH). Claims under this guarantee are subject to the device is properly installed and used in accordance with the instructions provided. Warranty is void where modifications or improper repairs, without prior consultation with the manufacturers, are carried out. Warranty is void where a device is improperly fitted. Further claims, for whatever legal reason, in particular, claims for direct or indirect damages are excluded.

Labeling

On the back you‘ll find the following labeling:![Hernik KIDSFLEX Kidsflex

head rest 16](https://manuals.plus/wp-content/uploads/2022/10/Hernik- KIDSFLEX-Kidsflex-head-rest-16.png)

Maintenance & product care

7.1. Pull off the cover
The cover can be removed and washed with a mild detergent in the fine washing program of the washing machine (30 °C). Please refer to the instructions of the washing label of the cover.
The plastic parts can be cleaned with soap and water. Do not use harsh cleaning materials (such as solvents).
DANGER! The child safety seat must not be used without the seat cover.

Remove the headrest (if available) by loosening the screw.
Now loosen the shoulder straps from the Velcro strip on the inside of the back plate.
The back cushion can now be removed.
Open the zipper and pull off the covers.
For pulling of the seat cushion, first loosen the belt connection between the belt lock and the seat plate.
Remove the seat plate, open the zipper and pull off the covers.

Technical characteristics

total height crown height back height seat width seat depth (adjustable) lateral support height (small) lateral support height (large) distance of lateral supports weight capacity

Size 1	Size 2	Size 2Xl
74 cm	80 cm	90 cm
67 cm	73 cm	82 cm
43 – 51 cm	49 – 57 cm	58 – 69 cm
31 cm	35 cm	40 cm
28 – 33 cm	34- 39 cm	40 – 46 cm
26 – 36 cm	26 – 36 cm	34.44 cm
30 – 40 cm	30 – 40 cm	38.48cm
16 – 28 cm	19 – 32 cm	24 – 37 cm
8,2 kg	8,9 kg	12,3 kg
22 kg	36 kg	75 kg