Guangdong Yongding Technology Co Ltd DS10PRO Smart Lock User Guide

Guangdong Yongding Technology Co Ltd DS10PRO Smart Lock

Required tools (not included)

What’s in the box

Parts List

Remove existing deadbolt

1. Do not discard the old lock + hardware until the new Lock has been successfully installed.
2. Remove the lock from the door, including the old latch.

Prepare the door and check the dimensions

Install the latch and strike plate

• Check the backseat and adjust the latch

• Hold the latch in front of the door hole, with the latch facing flush against the door edge. Check if the slotted hole is centred?

• YES
  No adjustment is required Proceed to the next step.

• NO
  The slotted hole is NOT centred. Rotate and pull the latch as shown to extend the latch.

Dimensions

Install the latch

Install the exterior keypad and the interior assembly

Installation instructions

• Don’t insert the key to the cylinder when installing the deadbolt!!! 2 Battery:
• Use new and NON-rechargeable 4 AA batteries for the best use.
• Don’t load batteries until the lock is completely installed.
• Adjust the latch to insert horizontally. If you have any problems, don’t hesitate to contact us through customer service at the first time.

Simple flowchart of installation

Please refer to the next section if you need a more detailed installation process.

Install interior assembly

• Mounting plate installation tips

Door lock left/right direction

• Left-hand door: The hinge is on the LEFT
• Right hand door: The hinge is on the RIGHT

Insert IC port

Check installation status

Correct Installation tips: Drive 2 Interior Assembly Screws into half way first to ensure good alignment, after that, tighten all screws completely with proper pressure.

Install the batteries and cover

Detect the door’s opening direction

Completely & properly install the door lock

• Under unlocking state
• Put on 4 AA batteries
• Voice prompts programming successfully in 5s, and green light flashes as well
• The door lock itself can detect the door’s opening direction (L or R)
• enter passcode to check if the deadbolt can extend/ retract correctly. Please wait for 5s for it to finish automatically being oriented before proceeding with setup operation after installation and power on.

PROGRAMMING INSTRUCTION

How to use it?

• Unlock the door from outside
• Indicator light signals
  • Green: A correct code was entered.
  • Blue: Programming in progress.
  • Red:
  • An incorrect code was entered.
  • Programming error.
  • Low battery warning.
• Lock the door from outside Auto lock mode
  • Auto lock mode is disabled by default, please turn Auto-lock on.
  • In auto-lock mode, the bolt will extend out automatically in 5/10/20/30/60 seconds after unlocking.
  • Manual mode
  • Press the “ ” button on the keypad to lock.

Lock the door from inside

• Deadlock/Privacy Button
  • Privacy mode is disabled by default
  • All Entry Codes are disabled except the programming code
  • Manual mode
  • Rotate the turn piece to the lock position.

Fingerprint register steps

Tips :
Register (add) the complete fingerprint area including up, down, left and right edges. Move your finger slightly each time when programming to improve accuracy.

Privacy mode

Restore factory settings
Delete all user codes, including master code:

Features

• Four ways to access it: code, key, fingerprint and app.

• Low power consumption,4 AA batteries can work for 1 year or 5000 times.

• Backlit keypad for use in low-light environments.

• 1 Programming Code and 300 user codes (Including 50 Fingerprints).

• Built-in disguise feature to protect your codes from prying eyes.
  • I ow battery warning indication.

• Use a screwdriver to remove the interior assembly.

• Press and hold the reset button for 5 seconds until the voice prompt & green light flash, the master code will return to the manufacturer default code’123456

•  After restoring the factory, Change the master passcode as soon as possible! beacuse of the master passcode can unlock the door.

Setting definitions

Warranty

Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, We extend a lifetime limited mechanical and finish warranty and a one-year limited electronics warranty to the original consumer user (*Original User” ) of our brand product against defects in material and workmanship, as long as the original User occupies the residential premises upon which the product was originally installed.
Warning
This manufacturer advises that no lock can provide complete security by itself, this lock maybe defeated by forcible or technical means or evaded by entry elsewhere on the property, No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified technician or other security professional.

Troubleshooting

App Operation Guide

Ne recommend using app because it’s easier to set and more convenient for future use.

1. Create an Account

2. Smart Life App

3. Android:Search Smart Life on Google Play.

4. iOS:Search Smart Life on the App store.

5. OR:Scan the QR code on the right to download Smart Life App. Sign up and log into your account with an email address. Log k

6. Pair Your Phone with the Smart Lock

7. Step 1: Press any key to wake up the lock, you will hear a voice prompt “Please add Bluetooth Administrator” .If not ,please reset the lock. Tap Add Device.

8. Step 2 : Add the lock discovered.Cten 2. Name the lock and Tan Mone.

9. Change the Admin Passcode
   Once the lock and your phone are paired, the default admin passcode 123456 is invalid. Tap Member Management→Admin→Add Code-Enter a 6-9 digit password and set a code name.
   Note: The first code you set is the admin passcode, it can be changed or deleted.

10. Set Fingerprints (up to 50)
    Tap Member Management→Admin→ Add Fingerprint-Follow the on-screen instructions to add a fingerprint.

11. Auto Lock
    Settings→Auto Lock Delay (Change the interval time as needed) Settings-Remote Unlock

FCC statement

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  Consult the dealer or an experienced radio/TV technician for help.

RF warning for Mobile device

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• Thic enuinmont chaule ho inctallor one anorator with minimum dictance Shem hotween tho radiator & wour bars

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>