THEGALLEY DR 18 D GT WashStations with DryDock Installation Guide
- June 3, 2024
- THEGALLEY
Table of Contents
THEGALLEY DR 18 D GT WashStations with DryDock
Installation Guide
Ideal Workstations®, Work&WashStations™, Workstations/WashStations™ with
DryDock™, BarStations® and WashStations™
Workstations
Right Hand Drain Orientation & Left Hand Drain Orientation
IMPORTANT
- Please note: Unlike typical undermount kitchen sink installations, The Galley Workstation is installed in the cabinet prior to the counter being templated. A wood support frame will need to be constructed and mounted inside the base cabinet(s) and recessed down 1.5 mm from the top of the cabinet(s).
- Leave the installation instructions tray affixed to The Galley Basin until the countertop has been templated, and leave the basin braces affixed to the Basin’s tiers until the countertop has been installed and silicone has cured for a minimum of one hour.
- The Workstation and Tap require a minimum of 571.5 mm inside the cabinet. For 610 mm deep inset cabinets installed against a wall, the cabinet must be pulled 25 mm away from the wall.
- For countertops with a laminated or built-up decorative front edge, construct the wood support frame to finish 1.5 mm below the underside of the countertop cutout area.
Inspect The Galley Basin for any damage prior to installation. For any questions or concerns please contact us immediately at 800.375.4255 or customerservice@thegalley.com.
Please refer to all local plumbing and building codes prior to installation.
Tools
Before You Begin
If your cabinet(s) have been built to accommodate your Galley Workstation, proceed to Step One. If you are joining two or more cabinets together to house the Galley Workstation, you will need to trim the bulkheads to create an 279 mm clearance for the Basin.
CONSTRUCT SUPPORT STRUCTURE
- A wood support frame (cleat system) will need to be built and installed into the cabinet(s). This frame will support the weight of The Galley Workstation. NOTE: Clips are NOT to be used.
- Construct the support frame so that the inside dimensions of the frame are 13 mm larger than the Basin’s inside width and length dimensions. Please refer to pages 1-8 for your Galley dimensions.
NOTE: For a Galley Workstation + DryDock™, the support frame must be built with 25 mm x 51 mm boards so that there is no interference with any undercounter appliances
ATTACH THE SUPPORT FRAME TO THE INTERIOR WALLS OF THE CABINET
IMPORTANT
Place the support frame into the cabinet flush with the front of the cabinet.
This will ensure that there is the minimum 76 mm plumbing space from the back
of the frame to the cabinet wall needed. The support frame must be installed
1.5 mm lower than the top of the cabinet.
NOTE: Use a level to ensure that the support frame is installed level in
the cabinet. Once installed, the top of the Basin Flanges will be flush with
the top of the cabinet.
Attach the support frame to the interior walls of the cabine
INSTALL THE WORKSTATION BASIN
- Carefully place The Galley Basin into the cabinet by resting the flanges on the support frame. All four flanges should rest on the support frame.
- Use a level to ensure that the flanges are level. The top of the flanges should be flush with the top of the cabinet.
- Position the Basin so that it is perfectly square within the cabinet.
YOU ARE NOW READY FOR THE COUNTERTOP FABRICATOR
Countertop Installation
Use the white template tray affixed to The Galley Basin flanges as your guide for the front to back, and left to right cutout. Refer to pages 1-8 for your overall cutout dimensions or refer to the drawing on the template tray.
NOTE:
The suggested maximum corner radius is 9.5 mm. Please refer to countertop
manufacturer’s warranted minimums The front to back cutout dimension must
always be exactly 457 mm.The finished countertop will not completely cover the
Basin flanges. A 13 mm will be exposed on the front and back flanges and a 457
mm exposed on the left and right flanges. Creating this reveal allows for the
Tools to slide across the upper tier.
-
STEP 1
- On the front and back flanges, measure exactly 13 mm from the inside of the Basin and mark with a pencil.
- On the left and right flanges, measure exactly 6 mm from the inside of the Basin and mark with a pencil. Now you are ready to tape the flanges with painters tape.
- Apply tape to the marked area, covering exactly 6 mm closest to the inside of the Basin. Ensure that the tape covers the entire length of the flanges and that it extends exactly 13 mm onto the front and back flanges.
IMPORTANT: Be sure that it does not extend more than 13 mm onto the front and back flanges as shown.
d) Apply tape to the marked area, covering exactly 13 mm closest to the inside of the Basin. Ensure that the tape covers the entire length of the flanges and that it extends exactly 6 mm onto the left and right flanges.
IMPORTANT: Be sure that it does not extend more than 6 mm onto the left and right flanges as shown.
-
STEP 2
Apply a heavy bead of silicone to the untaped part of the flange. -
STEP 3
Before setting the countertop in place, make sure the Basin is perfectly square in the cabinet. Set the countertop and position it properly so there is exactly 13 mm exposed reveal on the front and back flanges and exactly a 6 mm exposed reveal on the left and right flanges. Press countertop down on the flange. The silicone should fill any gaps. -
STEP 4
Once the countertop has been set and the reveals measured, remove the excess silicone that is on the taped flanges, (do not remove the tape in this step). Using a spray bottle and a cloth, carefully clean all excess silicone off of the exposed taped flange. -
STEP 5
Wait approximately one hour and remove tape and Basin braces. This will ensure there is a clean flange, free from silicone, which will enable the Tools to slide freely.
The Galley Workstation® Limited Lifetime Warranty
-
GALLEY WORKSTATION LIMITED LIFETIME WARRANTY
Seller provides a Limited Lifetime Warranty. Seller warrants its stainless steel sink, installed in a residential application, to be free from manufacturing defects in materials and workmanship under normal residential usage. This Limited Lifetime Warranty is subject to the warranty conditions and limitations as set forth below. -
WARRANTY CONDITIONS AND LIMITATIONS
Sellers warranty is non-transferable and is strictly limited to products correctly installed using our installation instructions and used in a residential environment. This warranty is limited to defects or damages resulting from normal residential use and does not cover surface corrosion, (chemical or natural, including exposure to salt air, sea spray, acid rain, or environmental chemicals), scuffs or scratches, misuse, abnormal or abusive use, dents, deformations caused by the impact of any object, improper installation, care and/or maintenance, commercial use, environmental factors causing damage, shipping or freight damage, or commons signs of normal wear and tear, (scratching, staining and alkaline etching of the finish over time due to use, cleaning practices or water or atmospheric conditions, are not manufacturing defects but are indicative of normal wear and tear, however, these symptoms are easy to remedy). This limited warranty is null and void if the Product has been repaired, altered, or modified other than by Seller or under Seller’s supervision. The Seller is not responsible for labor charges, installation or other incidental or consequential costs. In no event shall the liability of Seller exceed the purchase price of the product. If the product is installed outside of North America, Seller warrants product to be free from defects in material and workmanship for one -
year from the date the product is installed, with all other terms of this warranty applying except duration. If the product has not been purchased from Seller or from an Authorized Dealer or Distributor of the Seller, this warranty is null and void.
-
CULINARY TOOLS
The Culinary Tools are not covered under warranty. If a defect is found in normal residential use, Seller will, at its election, repair, replace or make appropriate adjustment. Natural Golden Bamboo Culinary Tools should not have prolonged exposure to direct sunlight or be stored outdoors in a humid environment. -
CARE AND MAINTENANCE
For care and maintenance instructions of all Galley products, please refer to the Use and Care section on thegalley.com. -
WARRANTY CLAIMS
For warranty service and to purchase replacement parts, please contact the Customer Service team. To arrange for service under warranty, please prepare the following information: -
Product model
-
Installation date
-
A description of the problem
The Galley range of goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
CONTACT US
- Website: www.winningappliances.com.au/s/services
- Email; service@winning.com.au
- Phone: +61 2 9694 0300
- Mail: Winning Appliances Pty Limited ACN 002 193 688 20A Danks Street Redfern NSW 2016
You must retain your original proof of purchase. Failure to produce proof of purchase when requested may, at The Galley, LLC’s discretion, invalidate your claim.
The warrantor is: The Galley, LLC. Attn: Warranty Claims 12626 South Memorial Drive Bixby, OK 74008 USA
Australian Representative:
Winning Appliances Pty Limited ACN 002 193 688 20A Danks Street Redfern NSW
2016 +61 2 9694 0300 Winning.com.au
Please include the original receipt with a description of the problem, model number, store, date of purchase, your name, address and telephone number.
Corporate Headquarters
The Galley, LLC 12626 South Memorial Drive Bixby, OK 74008 800.375.4255
thegalley.com
References
- THE GALLEY® | REINVENT YOUR KITCHEN
- Winning Group | We deliver inspiration
- Winning Appliances | Kitchen & Laundry Appliances
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>