Cuisinart Woodcreek 4-in-1 Pellet Grill [SMK0036AS, SMK0036ASO] Instruction Manual

Woodcreek

4-in-1 Pellet Grill
ASSEMBLY INSTRUCTIONS
Model SMK0036AS / SMK0036ASO

**ASSEMBLY INSTRUCTIONS:**
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL.

WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Cuisinart Woodcreek 4-in-1 Pellet Grill:

•  Phillips Screwdriver
•  Pliers or Wrench

Note: Most hardware is per-attached to the grill. You may need to loosen some screws partially while others may need to be removed in order to assemble parts. The screws that you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.

Step 1

• Remove 2 screws
• Attach FRONT PANELS **1** and **2**
• Tighten 2 screws

Step 2

• Loosen 6 screws 3-4 turns on FRONT LEGS**3**and **4**
• Do not remove screws
• Attach FRONT PANELS 1 and 2 using keyholes
• Tighten 6 screws

Step 3

• Loosen 3 screws
• Attach RIGHT SIDE PANEL **5**
• Tighten 3 screws on RIGHT SIDE PANEL**5**

Step 4

• Loosen 2 screws
• Attach LEFT SIDE PANEL **6**
• Tighten 2 screws on LEFT SIDE PANEL **6**

Step 5

• Loosen 2 screws
• Attach CART BRACE**7**
• Tighten 2 screws on CART BRACE **7**
• Remove 4 screws

Step 6

• Attach CART BASE **8**
• Tighten 4 screws (Removed from Step 5)

Step 7

• Loosen 8 screws on REAR LEGS **9** and **11**
• Attach BACK PANEL **10** to REAR LEGS 9 and  **11**
• Tighten 4 screws
• Remove 4 screws

Step 8

• Attach CART BASE **8** to rear legs
• Tighten 4 screws (Removed from Step 7)

Step 9

• Attach LEFT SIDE PANEL **6** and CART BRACE **7**
• Tighten 4 screws

Step 10

• Lock CASTERS **37**
• Attach CASTERS **37** to legs

Step 11

• Attach ACCESSORY HOOKS **33** to LEFT SIDE PANEL **6** and CART BRACE **7** with wing nuts

Step 12

• Loosen 1 screw
• Remove 2 screws

Step 13

• Loosen 5 screws
• Remove 2 screws

Step 14

• Set GRILL BODY **12** on cart
• Make sure screw drops into rear cart brackets
• Push GRILL BODY **12** to  back of cart
• Install 2 screws in FRONT BRACKETS (Removed from Step 12 and Step 13)
• Tighten 4 screws on cart brackets (2 screws left over will be used in future steps)

Step 15

• Remove 4 screws from GREASE CUP BRACKETS **22**
• Install GREASE CUP BRACKETS **22** to the bottom of the GRILL BODY **12** using 4 screws

Step 16

• Remove 2 screws
• Attach GREASE CHANNEL **26**
• Tighten 2 screws

Step 17

• Loosen 2 screws
• Attach LEFT SIDE CONTROL PANEL **21** to LEFT SIDE TABLE **19** over keyholes
• Tighten 2 screws
• Remove 1 screw and washer

Step 18

• Attach LEFT SIDE TABLE **19** to GRILL BODY **12** using keyholes
• Do not tighten screws at this time
• Install and tighten screw (Removed from Step 13)

Step 19

• Install screw and washer (Removed from Step 17)
• Make sure control panels are aligned
• Tighten 5 screws from Step 18 and Step 19

Step 20

• Remove 1 screw
• Loosen 2 screws
• Attach RIGHT SIDE CONTROL PANEL **20** to PELLET HOPPER **18** over keyholes
• Tighten 2 screws

Step 21

• Attach PELLET HOPPER **18** to GRILL BODY  **12**
• Tighten 4 screws (Find M6x35 screws bag with owners manual)

Step 22

• Install 2 screws (1 screw removed in Step 12 and 1 screw removed in Step 20)

Step 23

• Install PELLET HOPPER LID HANDLE **17** (screws, washers and bezels are pre-installed in handle)

Step 24

• Install TEMPERATURE GAUGE **14** and BEZEL **15** using washer and wing nut

Step 25

• Install HOOD HANDLE **13** (Wing nuts, bezels and washers are pre- installed on handle)

Step 26

• Remove 4 screws and washers
• Loosen 1 screw

Step 27

• Install AUGER HOUSING **32** using keyhole in firebox and slots in pellet hopper bracket
• Tighten 5 screws and washers in firebox

Step 28

• Remove 2 screws
• Attach CORD WRAP **28**using 2 screws

Step 29a

• Connect wiring for Controller and Pellet Sensor
• These wires can only be connected one way
• Make sure the connectors are lined up properly before tightening

Step 29b

• Once connected, twist to tighten

Step 29c

• Secure wiring with cord clip.

Step 30

• Attach CONTROL KNOB  **16** to controller

Step 31

• Attach HEAT BAFFLE 29

Step 32

• Install LEFT HEAT PLATE **30** on welded brackets
Note: The 2 longer feet go on the left side of the firebox

Step 33

• Install RIGHT HEAT PLATE **31** on welded brackets
Note : The angled lip should face left

**Step 34**

• Install COOKING GRATES **27** and WARMING RACK **24**

Step 35

• Install ASH CATCHER **25** and GREASE CUP **23**

Step 36

• Store GRIDDLE **36** on ACCESSORY HOOKS **33**

Step 37

• Store CERAMIC INSERT**34** and CHARCOAL INSERT **35** on ACCESSORY HOOKS **33**

Model SMK0036AS / SMK0036AS0 Assembled

OM0036AS/ASO
1019

©2019 The Boltz Group LLC
Carrollton, Texas 75006 U.S.A.

Assembly Instructions for Models
SMK0036AS / SMK0036ASO

Cuisinart Woodcreek 4-in-1 Pellet Grill [SMK0036AS, SMK0036ASO] Instruction Manual – Optimized PDF
Cuisinart Woodcreek 4-in-1 Pellet Grill [SMK0036AS, SMK0036ASO] Instruction Manual – Original PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>