Limei G2 GPS Speed Meter User Guide

June 1, 2024
Limei

Limei G2 GPS Speed Meter

Limei-G2-GPS-Speed-Meter-product

Specifications

  • Product Model : GPS Speed meter G2
  • Working Voltage : 5V
  • Display Functions: Satellite icon, Atmosphere light, Multi-function display
  • Display Unit: TRIP mileage, TIM clock, MPH miles, KM/H kilometers
  • Wave Button Functions: Short press, Long press, Push left, Push right

Product Usage Instructions

Display Functions

  1. Satellite Icon: Indicates satellite connection status. N-North, S-South, W-West, E-East.
  2. Atmosphere Light: Toggle on/off by pressing the wave button.
  3. Multi-function Display: Shows vehicle speed, time, number of satellites, and more. Use the wave button to cycle through functions.

Wave Button Functions:

  1. Short Press: Change displayed functions.
  2. Long Press: Enter settings mode, and save adjustments by pressing vertically for 2 seconds.
  3. Push Left/Right: Switch between standard and concise modes.

Setting Mode

To enter setting mode, long press the wave button. Use the right to navigate menus and short press to confirm settings. Save and exit by long pressing in for 2 seconds.

Warning: This product’s working voltage is 5V, and it is forbidden to use a voltage higher than 5V for power supply.

Display functions

Limei-G2-GPS-Speed-Meterfig-fig-1

  1. Satellite icon: After the satellite is found, it stops flashing and goes out before it can be used normally. N-North S-South W-West E-East
  2. Atmosphere light: Right-press the wave button to turn it off, and again to turn it on
  3. Multi-function display: vehicle speed, time, vehicle speed + time, number of satellites, travel distance, travel time (Short press the wave button vertically to change the function)
  4. Atmosphere light: Right-press the wave button to turn it off, and again to turn it on
  5. Multi-function display unit: TRIP mileage, TIM clock, MPH miles, KM/H kilometers

Wave button function

Limei-G2-GPS-Speed-Meterfig-fig-2

  1. Short press in: Switch to vehicle speed, Time, Vehicle speed + time, Number of satellites, Travel distance, Travel time
  2. Long press in: Enter the setting, after adjusting, press vertically for 2 seconds to save and exit
  3. Push left: Switch to standard mode or concise mode
  4. Long push left: Push left for 2 seconds to turn off the buzzer alarm and do it again to turn on
  5. Push right: Switch to concise mode or standard mode (move option after entering setting)

Enter setting mode

Long press in to enter into the setting mode, press right to choose the menu, and short press in to confirm. Once finishing the setting, long press in 2 seconds to save and exit.

Limei-G2-GPS-Speed-Meterfig-fig-3 Limei-G2-GPS-
Speed-Meterfig-fig-4

Troubleshooting

  1. The screen is without any display, and no power
    Check whether the USB cable is damaged, replace the USB cable for testing, and prohibit the use of voltage higher than 5V for power supply

  2. Without Car Speed
    After HUD power-on, the satellite icon flashes will start to look for the satellite. Please drive the car to the open road. It will work after it stops flashing

  3. Time calibration
    When the satellite icon flashes and no satellite is received, enter item 6 of the setting item to adjust the local time zone. The default is East Zone 8.
    After the satellite icon flashes and the satellite is found, enter item 6 of the setting item to adjust and calibrate the local time.

  4. Inaccurate Speed

    • a. First check the speed unit is correct or not, the speed unit including KM/H and MPH,(please refer to the setting mode to switch the unit).
    • b. The car manufacturers usually make the dashboard speed 5-7% higher than the ECU. The international standard is based on satellite data. (if the dashboard shows 100, and the device shows 105, change the default value to 102)
  5. Driving direction display error
    Satellites cannot tell where you are driving when there is no speed. After the vehicle speed exceeds 5 km / H, the direction can be displayed normally.

  6. Speed is still displayed after the car stops
    Under the underground parking lot, tunnel, and overpass, there will be unstable satellite drift when there is obstruction.

  7. Turn off the buzzer
    Push left for 2 seconds to turn off the buzzer, and do it again to turn it on.

FCC Requirement

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FAQs

Troubleshooting

  1. No Display or Power: Check the USB cable for damage. Use a 5V power supply only.
  2. No Car Speed Display: Drive to an open road until the satellite icon stops flashing.
  3. Time Calibration: Adjust the local time zone in setting item 6 when no satellite is received.
  4. Inaccurate Speed: Check the speed unit and adjust the parameter value based on dashboard readings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals