Einhell BT-BG 175 Double Wheel Grinder or Sander Instruction Manual

June 3, 2024
Einhell

Einhell Logo Operating Instructions
Double-Wheel Grinder/Sander
Art.-Nr.: 44.126.04
I.-Nr.: 01017

BT-BG 175 Double Wheel Grinder or Sander

Einhell BT BG 175 Double Wheel Grinder or SanderEinhell BT BG 175 Double Wheel Grinder or Sander -
Fig

Important!
When using equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, give them these operating instructions as well. We accept no liability for damage or accidents which arise due to non-observance of these instructions and the safety information.

Safety regulations

The corresponding safety information can be found in the enclosed booklet.

Layout (Fig. 1)

  1. ON/OFF switch
  2. Safety window
  3. Spark deflector
  4. Safety hood
  5. Grinding wheel
  6. Workpiece support fastening screw
  7. Workpiece support
  8. Mounting holes
  9. Foot
  10. Spark deflector fastening screws
  11. Spark deflector adjusting screw
  12. Washer
  13. Lock washer
  14. Workpiece support locking knob
  15. Workpiece support holding

Proper use

A double grinder is a multi-function tool for the rough and precision grinding of metals, plastics, and other materials using a selection of grinding wheels. The machine must only be used for its intended purpose! Even if the machine is used as intended, certain residual risk factors cannot be completely eliminated. The following hazards may arise in connection with the machineʼs construction and layout:

  • Contact the grinding wheel where it is not covered.
  • Catapulting of parts from damaged grinding wheels.
  • Catapulting of workpieces and parts of workpieces from the machine.
  • Damage to hearing if ear-muffs are not used as necessary.

The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the the machine is used in commercial, trade, or industrial businesses or for equivalent purposes.

Technical data

Rated voltage: 230 V ~ 50 Hz
Power rating: 400 W  S2  30 min
Idle speed n 0: 2800 min-1
Grinding wheel diameter: 175 mm
Grinding wheel thickness: 25 mm
Grinding wheel hole diameter: 32 mm
Max. peripheral speed: 25.64 m/s
Weight: 10.2 kg

Load factor:
A load factor of S2 30 min (intermittent periodic duty) means that you may operate the motor continuously at its nominal power level (400 W) for no longer than the time stipulated on the specifications label (30 minutes ON period). If you fail to observe this time limit the motor will overheat. During the OFF period the motor will cool again to its starting temperature.
Noise emission levels
The noise emitted by this saw is measured in accordance with EN ISO 3744; EN ISO 11201 The noise at the workplace may exceed 85 db (A). The user will require noise protection measures if this is the case. (Wear ear-muffs!)
No-Load operation

Sound pressure level LpA 81,5 dB
Sound power level LWA 94,5 dB

Before starting the equipment

Pull the power plug before doing any maintenance or assembly work on the equipment.

  • The machine must be set up so that it stands firmly, i.e. it must be securely screwed to a workbench or similar.
  • All covers and safety devices have to be properly fitted before the machine is switched on.
  • It must be possible for the grinding wheel to run freely.
  • Check that the voltage on the rating plate is the same as your supply voltage before you connect the machine to the power supply.

5.1 Assembling the spark deflector (Figs. 1/3/4/5)

  • Slide the spark detector (3) under the safety hood (4). Screw the spark deflector (3) to the safety hood from above (4) using the screws (10) (Fig. 4).
  • Adjust the spark deflector (3) using the adjusting screw (11) so that the distance between the dry grinding wheel (5) and the spark deflector (3) is as small as possible and certainly does not exceed 2 mm.
  • Adjust the spark deflector (3) periodically to compensate for wear on the wheel.

5.2 Assembling the workpiece support (Fig. 2/6)
Fit the workpiece support (7) to the workpiece support holder (15) using the workpiece support fastening screw (6), washer (12), lock washer (13), and workpiece support locking knob (14), as shown in Fig. 6.
5.3. Changing the grinding wheel (Figs. 7-8)
Remove the 3 screws (A) holding the side section of the safety hood (B) and remove the safety hood. Undo the nut (D) (Important: The left grinding wheel is fastened with a left-handed thread and the right grinding wheel with a right-handed thread), by holding the nut of the grinding wheel mounted on the opposite side. Remove the flange (C). and replace the grinding wheel (5). To assemble, proceed in reverse order.

Operation

6.1 ON/OFF switch (1)
To switch on the equipment set the On/Off switch (1) to position 1.
Move the ON/OFF switch (1) to position 0 to switch off the equipment.
After switching on the equipment wait for the equipment to reach its maximum speed of rotation before commencing with the sanding/grinding work.
6.2 Grinding

  • We recommend that you use the fine-grained grinding wheel for fine sanding/grinding work and the coarse-grained grinding wheel for coarse sanding/grinding work.
  • Place the workpiece onto the workpiece support (7) and slowly guide the workpiece towards the grinding wheel (5) at the desired angle to the point where workpiece and grinding wheel make contact.
  • Move the workpiece slightly back and forth to produce an optimal grinding result. This way the grinding wheel (5) is evenly worn. Allow the workpiece cool every now and then.

Cleaning, maintenance, and ordering of spare parts

Always pull out the mains’ power plug before starting any cleaning work.
7.1 Cleaning

  • Keep all safety devices, air vents, and motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
  • We recommend that you clean the device immediately each time you have finished using it.
  • Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device.

7.2 Maintenance

  • There are no parts inside the equipment which require additional maintenance.

7.3 Ordering replacement parts:
Please quote the following data when ordering replacement parts:

  • Type of machine
  • Article number of the machine
  • Identification number of the machine
  • Replacement part number of the part required
    For our latest prices and information please go to www.isc- gmbh.info

Disposal and recycling

The unit is supplied in packaging to prevent its being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system.
The unit and its accessories are made of various types of material, such as metal and plastic.
Defective components must be disposed of as special waste. Ask your dealer or your local council.
** declares conformity with the EU Directive and standards marked below for the article
Doppelschleifer BT-BG 175**

X 2006/42/EG 87/404/EWG
X 2006/95/EG R&TTED 1999/5/EG
97/23/EG 2000/14/EG_2005/88/EG:
X 2004/108/EG 95/54/EG:
90/396/EWG 97/68/EG:
89/686/EWG

EN 61029-2-4; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 19.06.2007

Art.-Nr.: 44.126.04
I.-Nr.: 01017
Subject to change without notice
Archivierung: 4412600-36-4155050
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products, is permitted only with the express consent of ISC GmbH.
Technical changes subject to change
For EU countries only
Never place any electric tools in your household refuse.
To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment- friendly fashion, e.g. by taken to a recycling depot.
Recycling alternative to the demand to return electrical devices:
As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the device is properly recycled if ownership is relinquished. This can also be done by handing over the user device to a returns center, which will dispose of it in accordance with national commercial and industrial waste management legislation. This does not apply to the accessories and auxiliary equipment without any electrical components which are included with the user device.

GUARANTEE CERTIFICATE

Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which guarantee claims can be made:

  1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee.
  2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or the replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by the device being dropped) and normal wear resulting from the proper operation of the device. The guarantee is rendered null and void if any attempt is made to tamper with the device.
  3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies when on-site service is used.
  4. In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy to offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units that are no longer covered. To take advantage of this service, please send the device to our service address.

Service Hotline: 01805 120 509 · www.isc-gmbh.info
(0,14 € /min. Festnetz T-Com) – Mo-Fr. 8:00-20:00 Uhr
Name:———————
Retouren-Nr. iSC:———————
Straße / Nr.:—————————-
Telefon:—————————–
PLZ —————————-
Ort————————
Mobil:———————
Welcher Fehler ist aufgetreten (genaue Angabe):
Service Hotline
Einhell Logo

Documents / Resources

| Einhell BT-BG 175 Double Wheel Grinder or Sander [pdf] Instruction Manual
BT-BG 175, Double Wheel Grinder or Sander, BT-BG 175 Double Wheel Grinder or Sander, Grinder or Sander, Grinder, Sander
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals