ideal lux Cantina SP1 Suspension Lamp Instruction Manual

: June 1, 2024
: ideal lux

Table of Contents

ideal lux Cantina SP1 Suspension Lamp
Product Specifications
Product Usage Instructions
FAQ
FEATURES
DIMENSIONS
Installation Instructions
SAFETY INSTRUCTIONS
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ideal lux Cantina SP1 Suspension Lamp

Product Specifications

Model: Cantina SP1
Socket Type: E27
Max Wattage: 1 x 42W
Voltage: 220~240V, 50/60Hz
Color Options: BRUNITO (8021696112701), RAME (8021696112732)

Product Usage Instructions

Installation

Ensure installation is done by a qualified electrician.
Follow the assembly instructions provided in numerical order.

Safety Instructions

Always disconnect from power before installation or maintenance.
Use appropriate fixtures and accessories for mounting.
Do not disassemble the LED light source.
If the lamp does not turn on, replace the fuse.
Grounding is mandatory for electrical safety.

Electrical Safety Classes

Class I: Requires grounding for safety.
Class II: Double insulation, no grounding required.
Class III: Operates at very low voltage, no grounding required.

Protection Ratings

IPX0: Not protected
IPX5 – IPX8: Various levels of protection against solids and liquids

FAQ

Q: Can the LED light source be replaced?
A: No, the LED light source is not replaceable. Do not attempt to disassemble it.
Q: What should I do if the lamp does not turn on?
A: Check and replace the fuse if needed. If the issue persists, consult a qualified electrician.
Q: Is grounding mandatory for this product?
A: Yes, grounding is mandatory for electrical safety, especially for Class I electrical safety.

Cantina SP1

Suspension lamp
E27 max 1 x 42W / 220~240V 50/60Hz
- 8021696112701 BRUNITO
- 8021696112732 RAME

FEATURES

ideal-lux-Cantina-SP1-Suspension-Lamp-fig-4

DIMENSIONS

Installation Instructions

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

ideal-lux-Cantina-SP1-Suspension-Lamp-fig-5

SAFETY INSTRUCTIONS

This fitting is produced and tested by the strictest European safety standards (EN 60.598- 1).
This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
Always isolate power before commencing installation, maintenance or repair.
The luminaire contains certain parts which can be very hot.
Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
Always tighten the screws firmly to avoid contact problems.
This fitting should only be installed indoors.
Luminaires are not suitable for recessed on normally flammable surfaces.
Luminaire is not suitable for direct mounting on normal flammable surfaces.
This fitting is only suitable for fixing to the ceiling.
This fitting is only suitable for fixing to the wall.
The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
Only use lamps that do not exceed the maximum specified wattage.
Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
Light source with not-substitutable light emitting diode (LED). Do not disassemble the product
since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
Class || Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded
Not protected.
Protected against solid objects greater than 50 mm.
Protected against solid objects greater than 12 mm.
Protected against solid objects greater than 2,5 mm.
Protected against solid objects greater than 1mm.
Dust protected.
Totally protected against dust infiltration.
Not protected.
Protected against vertically falling water drops.
Protected against water drops falling with a maximum angle of 15° to the vertical axis.
Protected against rain.
Protected against splashing water.
Protected against water jets.
Protected against strong water jets.
Protected against temporary immersion.
Protected against prolonged immersion.
Luminaire not suitable for covering with thermally insulating material.
Caution, risk of electric shock.
Do not stare at the operating light source.