scheppach 1906302901 Woova 3.0 Dust Extractor Instruction Manual

: June 3, 2024
: Scheppach

Table of Contents

Technical data
General notes
Safety notes
Use only as authorized
- The machine meets valid EC machine guidelines
Remaining hazards
Assembly
Initial operation
Electrical connection
Maintenance
Special accessoires
EC declaration of confirmity
Documents / Resources

scheppach 1906302901 Woova 3.0 Dust Extractor

Technical data

Length/ width/ height mm ………………………………………….650x415x1850
Overal height wit filter cartridge mm ………………………………………… 1850
Extrcacto duct connections, diameter mm …………………………………. 100
Hose diameter mm …………………………………………………………………….. 100
Hose length mm ………………………………………………………………………. 2500
Wheel diameter mm ……………………………………………………………………. 75
Steering roller diameter mm ……………………………………………………….. 75
Approx weight ca. kg …………………………………………………………………31,5
Rate of air flowm³/h………………………………………………………………… 1000
Pressure differential Pa ……………………………………………………………. 1200
Filter area (filter bag) m² …………………………………………………………… 1,00
Filter area (filter cartridge) m² …………………………………………………… 5,00
Sawdust bag capacity litres ………………………………………………………….. 80

Motor

|

230 V / 50 Hz

|

400 V / 50 Hz

---|---|---
Nominal input P1 (kW)|

0,60

|

0,55

Output power P2 (kW|

0,37

|

0,37

Noise parameters

The noise emission values determined according to EN 3746 for the sound level and according to EN 1807 (coefficient of correction k3 calculated according to Appendix A.2 of EN 1807-1) for the sound level at the workplace are as follows, based on the working conditions listed in ISO 7960 Appendix J.
The values stated are emission values and are therefore not necessarily safe operating values. Although there is a correlation between emission and immission levels, you cannot reliably deduce from this whether additional safety measures are required or not. Factors which can influence the immission level currently at the workstation comprise the duration of the effects, the characteristics of the work room, other sources of noise etc., for example, the number of machines and adjacent operations. The permissible values per workstation can also vary from country to country. This information should nevertheless enable the user to make a better estimation of dangers and risks.
Sound level at the workplace in dB
Idle running LpAeq = 75 dB(A)
Operation LpAeq = 75 dB(A)
A measurement uncertainty allowance K = 4 dB applies to the mentioned emission values.

General notes

After unpacking, check all parts for any transport damage. Inform the supplier immediately of any faults.
Later complaints cannot be considered.
Make sure the delivery is complete.
Before putting into operation, familiarize yourself with the machine by carefully reading these instructions.
Use only original scheppach accessories, wearing or replacement parts. You can find replacement parts at your scheppach dealer.
When ordering, include our item number and the type and year of construction of the machine.

NOTE:

In accordance with valid product liability laws, the manufacturer of this device shall not be responsible for damage to and from this device which results from:

Improper care.
Noncompliance with the Operating Instructions.
Repairs made by unauthorized persons.
The installation and use of any parts which are not original scheppach replacement parts.
Improper use and application.
Failure the electrical system as a result of noncom pliance with the legal and applicable electrical directives and VDE regulations 0100, DIN 57113 / VDE 0113.

We recommend that you read through the entire operating instructions before putting into operation

These operating instructions are to assist you ingetting to know your machine and utilize its proper applications.
The operating instructions contain important notes on how you work with the machine safely, expertly, and economically, and how you can avoid hazards, save repair costs, reduce downtime and increase the reliability and service life of the machine. In addition to the safety requirements contained in these operating instructions, you must be careful to observe your country’s applicable regulations.
The operating instructions must always be near the machine. Put them in a plastic folder to protect them from dirt and humidity. They must be read by every operator before beginning work and observed conscientiously. Only persons who have been trained in the use of the machine and have been informed of the various dangers may work with the machine. The required minimum age must be observed.
In addition to the safety requirements contained in these operating instructions and your country’s applicable re gulations, you should observe the generally recognized technical rules concerning the operation of woodworking machines

Warning! This electric tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under certain conditions. In order to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the manufacturer of the medical implant prior to operating the electric tool.

Safety notes

Please pass on safety notes and instruction
See to it that safety instructions and wamings attached to the machine are always complete and perfectly legible.
Check all power supply lines. Do not use defective lines.
Insure that the planing machine is set up in a sta ble position on firm ground.
Protect the machine from moisture and dampness.
Keep children away from the machine when it is connected to the power supply.
Operating personal must be at least 18 years of age. Trainees must be at least 16 years ofage,but may only operate the machine under adultsupervision.
Connection and repair work on the electrical installation may be camed out by a qualified electrician only.
Note the motor rotationat direction – see electrical connection.
Switch the machine off and pull power supply plug when rectifying any malfunctions.
Persons unfamiliar with the machine may not operate it.
Perform maintenance tasks, change bag, filter, orhose only with mains plug unplugged.
In hazardous locations, only special explosion proof devices may be operated. Use only original accessories.
Verify proper functioning of the machine before each use.
Do not use the machine at temperatures below 0 °C, at risk of damaging the housing.
When leaving the work place, switch the motoroff. Pull the power supply plug.
Cut off the external power supply of the machine or plant even if inly minor changes of place are envisaged. Properly reconnect the machine to the supply mains before recommissioning.

Use only as authorized

The machine meets valid EC machine guidelines

The machine has been built in accordance with state-of-the-art standards and the recognized safety rules. Nevertheless, its use may constitue a risk to life and limb of the user or of third parties,or cause damage to the machine and to othermaterial proper-ty.
The machine must only be used in technically perfect condition in accordance with its designated use and the instructions set out in the operating manual, and only by safety-conscious persons who are fully aware of the risks involved in operating the machine. Any functional disorders, especially those affecting the safety of the machine, should therefore be rectified immediately. The vacuum exhaust unit is designed only for removing saw dust (nor for normal dust).
Regularly inspect the filter for damage.
Replace damaged filters!
Regularly check that the housing is well sealed and regularly inspect the filter and saw dust sackseals.
Do not allow foreign objects such as screws, nails, plastic or wood chips to enter the cleaning nozzle.
The machine must only be used with original parts and orginal accessories supplies by the manufacturer.
The Exhaust System woova 3.0 is constructed exclusively for exhaust-vacuuming wood chips and saw dust and may only be used in connection with wood processing machines.
When vacuuming shop floors, wood or metal pieces may not be vacuumed.
Any other use exceeds authorization. The manufacturer is not responsible for any damages resulting from unauthorized use; risk is the sole responsibility of the operator.
The safety, work and maintenance instructions of the manufacturer as well as the technical data given in the calibrations and dimensions must be adhered to.
Relevant accident prevention regulations and other, generally recognized safety technical rules must also be adhered to.
The machine may only be used, maintained, and operated by persons familiar with and instructed in its operating and procedures. Arbitrary alterations to the machine release the manufacturer from all responsibiliy for any resulting damages.
The machine may only be used with original accessories made by the manufacturer.

Remaining hazards

The machine has been built using modem technology in accordance with recognized safety rules. Some remaining hazards, however, may still exist.

Wood chips and sawdust can be health hazards. Be sure to wear personal protective gear such as safety goggles and a dust mask.
Dust inhalation may occur when closing and replacing the dust bag. Please note the instructions concerning proper disposal in the operating manual (e.g. the use of P2 dust masks) to prevent dust inhalation.
Noise can be a health hazard. The permitted noise level is exceeded when working. Be sure to wear personal protective gear such as ear protection.
The use of incorrect or damaged mains cables can lead to injuries caused by electricity.
Even when all safety measures are taken, some remaining hazards which are not yet …. evident may still be present.
Remaining hazards can be minimized by following the instructions in “Safety Precautions”, “Proper Use“ and in the entire operating manual.

Assembly

For packaging reasons your Woova 3.0 is delivered in semi-assembled state.

Tools required for assembly not included in shipment

1 Open-end wrench SW 10
1 Open-end wrench SW 17
2 Open-end wrenches SW 13
1 Nut driver SW 8
1 Screwdriver

Assembly frame Fig. A Axle and wheels

2 lock washers

Place the wheels onto the wheel axle. Use the assembly tool and a hammer, and force the fastening cap on to the wheel axle

Steering Rollers

2 pan-head screws M10x20
2 serrated lockwashers A10,5
2 acorn nuts M10

Frame feet and plate

8 hex screws M8x12
8 serrated lockwashers A8,2
8 acorn nuts M8

Fig. B Screw housing onto frame

4 hex screws M8 x 12
4 serrated lockwashers Insert filter bag hanger. A8,2

Extractor hose

Put hose clamps over hose ends,Insert hose couplings and tighten the hose clamp. Clamp the extractor hose tightly onto the housing bracket with hose clamp.

Filter bag, Fig. C

Lay locking band (280 mm diameter) on housing.
Fit filter bag over housing collar and fasten with locking band.

Sawdust bag, Fig. D

Open clamping lug.
Fit sawdust bag over ejection opening, fold at clamp recess and close clamping lug.
Lay locking band (337 mm diameter) over sawdust bag and fasten.

Initial operation

Note safety instructions before operation. The data on the motor type plate (voltage and frequency) must conform to the mains supply voltage and frequency. After connection to themains, the Dust Extractor Woova 3.0 is ready for operation

Electrical connection

Connection and repair work on the electrical equipment must be carried out by a qualified technician only.

The installed electric motor is factory connected ready for operation.

The connection made by the customer as well as any extension cables used must comply with all relevant regulations.

Important note
Defective electrical connection cables
Electrical connection cables often suffer isolation damage.

Possible causes are:

Pinch points when connection cables are run throught window or door gabs.
Kinks resulting from incorrect attachment of laying of the connection cable.
Cuts resulting from running over the connection cable.
Isolation damage resulting from forcefully pulling out of the wall socket.

Such defective electrical connection cables must not be used as the isolation damage makes them extremly h a z a r d o u s.

Check electrical connection cables regularly for damage. Make sure the cable is disconnected from the mains when checking. Electrical connection cables must comply with the regulations applicable in your country.

One phase motor

The mains voltage must comply with the specification on the motor name plate.
Extension cables must have a cross section of at least 1.0 sqmm.
The mains is protected by a 16 A slow blow fuse.

Three phase motor

The mains voltage must comply with the specification on the motor nameplate
Mains connection cable and any extensions must be 5-lead cables = 3P + N + PE
Extension cables must have a cross section of at leas 1,5 sqmm
The mains is protected by max. 16 A
When connecting to the mains or relocating the machine, check the direction of rotation and change polarity if neccessary (wall socket)

When making inquiries please specify the following

Motor manufacturer
Motor current type
Motor nameplate specifications
Switch nameplate specifications

When sending the motor in, always send the complete drive unit including the switch.

Maintenance

For all maintenance and cleaning tasks, tum off motor and unplug mains.

Connection and repair work on the electrical installation may be carried out by a qualified electrician only.
For constant performance, periodically shake out filter bag vigorously. Between cleanings, beating the bag with the hand several times is sufficient
The sawdust bag must be replaced a1 the latest when the sawdust is within 10 cm. of the housing collar

Service information

Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumablesWear parts*: Carbon brushes, filter bag, suction hose, nozzle inserts, V-belts

Not necessarily included in the scope of delivery!

Special accessoires

Filter bag
Part. no. 7500 1019
Filter cartridge
Part. no. 7500 6000
Reusable sawdust bag
Part.no. 7500 1500 20 pc.
Extension coupling
Part. no. 7500 3300

EC declaration of confirmity

scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
89335 Ichenhausen
Deutschland

Bevollmächtigter: Reinhold Bauer

We, scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH declare, that the machine described below
Dust extractor Woova 3.0, from serial number 1001 , Articlenumber 1906302901, Articlenumber 1906302902
complies with all relevant requirements EG-Maschinenrichtlinie 2006/42/EG

Other directives:
EG-EMV Richtlinie 2014/30/EU

Applied harmonized standards, especially:
EN 12100-1, 12100-2, EN 349, EN 60 204-1

Representative for the compilation of technical documents:
Reinhold Bauer

i.V Reinhold Bauer (Konstruktionsleiter) Dokumentationsbeauftragter

Documents / Resources

| scheppach 1906302901 Woova 3.0 Dust Extractor [pdf] Instruction Manual
1906302852, 1906302901 Woova 3.0 Dust Extractor, 1906302901, Woova 3.0 Dust Extractor, Dust Extractor, Extractor
---|---