IKEA UPPÅTVIND Floor Lamp with LED Bulb User Manual

IKEA UPPÅTVIND Floor Lamp with LED Bulb User Manual

READ AND SAVE THESE INSTRUCTIONS

Read all instructions before using the product.

DANGER
To reduce the risk of electric shock: Always unplug this product from the electrical outlet before cleaning.

WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons, do not use this fan with any Solid-State speed control device.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved by a person responsible for their safety. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

Electricity safety

• Do not use a damaged power plug or loose electrical outlet.
• Do not move the product by pulling the power cord.
• To prevent the power cord from being damaged or deformed, do not forcibly bend it or run it under a heavy object.
• If the electrical outlet is wet, carefully unplug the product and allow the electrical outlet to completely dry before subsequent use.
• Do not handle the power plug with a wet hand.
• Do not plug in and unplug the power plug repeatedly.
• Unplug the product before inspection or parts replacement.
• Remove any dust or water from the power plug.
• Unplug the product if it is not to be used for a long time.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Do not attempt to repair or modify the power cord.
• This product shall only be used together with the included power supply unit.
• If any part is damaged, the product should not be used.

Installation safety

• The product is only intended for household use under normal operating conditions.
• Do not install the air purifier near a heating device.
• Do not use the product in wet environments or in environments with high humidity, such as the bathroom or in a room with great variations in temperature.
• Leave at least 30 cm of free space around the product.
• Do not use the product in areas where flammable gases or combustible materials are used or stored.
• Do not exert excessive force or subject the product to bumps and bangs.
• Install the product so that no obstacles around the product block the circulation of air.

Operation safety

• Never place the product in water.
• Do not disassemble, repair or modify the product.
• Unplug the product before you clean it.
• If the air purifier produces a strange noise, burning smell or smoke, immediately remove the power plug from the electrical outlet and call our Customer support.
• Do not spray any flammable materials into the air inlet.
• Do not stick fingers or foreign objects into the air inlet or outlet.
• Replace the filter with a new one according to filter replacement cycles. Product performance may otherwise deteriorate.
• Do not push or lean against this product since it may tip over and cause physical injury or product malfunction.

Care Instructions

Unplug the product before cleaning.
To clean the product, wipe with a soft moistened cloth. Use another soft, dry cloth to wipe dry.
Vacuum-clean the pre-filter regularly.

Note!
Never use abrasive cleaners or chemical solvents as this can damage the product.

Fan speed control

The fan can be set to 3 different speeds by pressing the power button multiple times.
A long press will turn the air purifier OFF regardless of current speed level. The LED lamp’s brightness indicates the chosen speed level.

Filter replacement

When replacing the filter, it is essential that the user proceeds as follows:

A LED light on the control panel indicates when you should check your filters.

Warning!
The power supply cord must be disconnected during filter replacement!

1. Disconnect the power and wait until the fan has stopped.

2. Remove the pre-filter by the finger indent. Clean the pre-filter with a vacuum cleaner or with water depending on how dirty it is.

3. Remove the particle filter and handle the used filter carefully, dispose of the filter in accordance with local environmental regulations in your country.

4. Clean inside, removing all dust and dirt.

5. Reconnect the power supply cord.

6. Press and hold the RESET button for 3 seconds. The reset initialises the filter replacement cycle counter.
   

7. Insert the new particle filter.

8. Fix the pre-filter in place.

• Wash your hands thoroughly after replacing the filter.

Technical specifications

• Model: UPPÅTVIND air purifier

• Type: E2111

• Input: 24.0V DC, 0.8 A, 19.0W

• Dimensions:
  280 x 225 x 125 mm (HxWxD)

• Weight: 1.6 kg

• Filter: Filter for particle removal.

• Operational temperature:
  10 °C to 40 °C (50 °F to 104 °F).

• Humidity when operational:
  10-60% RH

(Recommended operational humidity: 40-60% RH)

Technical data PSU

• Type: ICPSW24-19-1 ICPSW24-19-1A
• Input: 100-240 VAC, 50/60 Hz, 0.4A
• Output: 24.0V DC, 0.8 A, Max 19.0W
• Indoor use only
• Manufacturer: IKEA of Sweden AB
• Address:
• Box 702, SE-343 81 Älmhult, SWEDEN

Filter cleaning and replacement cycles

The recommended filter replacement cycles may differ depending on the operating environment.

Run modes with filter for particle removal.

FCC Statements

This device complies with Part 15 of the FCC Rules.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation Science and Economic
Development Canada’s licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including  interference that may cause undesired operation of the device.

WARNING:
Any changes or modifications to this unit not expressly approved by the  party responsible for compliance could avoid the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the quipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Disposal

 The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>