Advanced Microwave Engineering LPSUWB-BT Amesphere Tablet User Manual

Advanced Microwave Engineering LPSUWB-BT Amesphere Tablet

Product Information

Specifications

• Product Name: AMESPHERE KEY AMESPHERE TABLET AMESPHERE TAG
• Model Number: V01
• Manufacturer: Advanced Microwave Engineering S.r.l.
• Head Office: Via Lucca 44, 50142 Florence, Italy C.F/P.IVA/n. iscr. Reg. Impr. di Firenze 05016620485
• Capitale sociale: 99.000 i.v.
• Contact: T. +39 055 73921, M. info@ameol.it
• Website: www.ameol.it

Product Usage Instructions

Smaltimento (Disposal)
Follow the local regulations for proper disposal of the product.

Destination and Limitations of Use

Use the product only for the intended purposes specified in the user manual. Do not use the product in environments with extreme temperatures or high humidity.

Follow the installation instructions provided in the user manual to properly install the product. Make sure to provide the drivers with the necessary instructions for using the product.

• Disposal
  Dispose of the product by local regulations.

• Destination and Limitations of Use
  Use the product only for its intended purposes as described in the user manual. Avoid exposing the product to extreme temperatures or high levels of humidity.

• Product Installation and Driver Instructions
  Refer to the user manual for detailed instructions on how to install the product. Provide the drivers with the necessary instructions for operating the product.

• A.M.E. Producer’s Disclaimer
  The manufacturer, A.M.E., disclaims any liability for damages or malfunctions caused by improper use or installation of the product.

• Additional Directions for Use: USA and Canada
  For users in the USA and Canada, please follow the additional directions provided in the user manual specific to your region.

FAQ (Frequently Asked Questions)

• Q: Can I use the product in extreme temperatures?
  A: No, it is not recommended to use the product in environments with extreme temperatures.

• Q: How do I dispose of the product?
  A: Follow the local regulations for proper disposal of the product.

• Q: Where can I find additional directions for use?
  A: Additional directions for use can be found in the user manual specific to your region.

REVISION TABLE

Data| Rev|

Note

---|---|---
14/12/2022| 01| Prima Stesura

SCOPE

This manual contains the basic instructions for safe installation and use. It must be read carefully in its entirety. For further information on the configuration visit: support.ameol.it.

SYSTEM COMPONENTS

ACCESSORIES

SAFETY INSTRUCTIONS

Disposal
Treatment of End-of-Life Electrical or Electronic Equipment (applicable in all European Union countries and other European countries with separate waste collection systems) This symbol indicates that the product must be handed over to an appropriate collection point for the recycling of electrical and electronic equipment.

The AMESPHERE (cod. LPSUWB001, LPSUWB002, vt-7 PRO, TAGSAFETYUWB2, TAGUWBCHARGER) is an assembly of electrical and electronic equipment. By ensuring that this product is disposed of properly, you will help prevent potential negative environmental and health consequences that could otherwise result from its improper disposal. Recycling materials helps to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service. Penalties may be applicable for improper disposal of electrical and/or electronic equipment, by local regulations.

DESTINATION AND LIMITATIONS OF USE
The AMESPHERE (cod. LPSUWB001, LPSUWB002, vt-7 PRO, TAGSAFETYUWB2, TAGUWBCHARGER) (hereinafter also referred to as ‘System’ or ‘Product’) is intended for installation on industrial trucks. The Product is an assistance system for human-vehicle and vehicle-vehicle proximity detection. It does not constitute a personal safety system and is not a safety device. It is not covered by Annex IV of Directive 2006/42/EC and as such cannot be used for residual risk reduction. Unless otherwise expressly stated in writing by A.M.E. on a case-by-case basis, the System is not intended for use in special environments such as flammable gas atmospheres, explosive atmospheres, or corrosive atmospheres. The purpose of the System is to provide an additional aid to the driving of industrial trucks. While driving, however, the driver’s full attention is required at all times and the driver must be ready to intervene and operate the controls to avoid possible collisions or other hazardous situations, regardless of and apart from the System.

The System is not a substitute for the driver’s attention and judgment and in no way obviates the need for the driver to slow down or brake in a hazardous situation, nor does it relieve the Buyer and the operator of the need to adopt normal safety procedures as required or appropriate. The control of the vehicle remains in any case in the total responsibility and availability of the driver, who must always evaluate the conditions in which the vehicle moves, paying attention to the presence of operators, other vehicles, obstacles, and dangers in general.

PRODUCT INSTALLATION AND DRIVER INSTRUCTIONS
When installing the Product, it is necessary to comply with the instructions and indications provided by the vehicle manufacturer in the relative user manual (electrical and mechanical connections, etc.). The installation must be carried out by personnel suitably trained for this purpose and must not make or involve changes to the vehicle that affect the characteristics and/or requirements relevant to the declaration of conformity of the vehicle itself.

The System shall be installed in such a way that, under any circumstances, the driver of the vehicle is not prevented from bringing the vehicle to a safe state. The installation shall also not compromise the ergonomics and visibility of the driving position. The operator must be warned against developing dependence on assistance systems. Under no circumstances should the driver abandon normal cautionary behaviours. The operator must be properly instructed that even in the event of a sudden failure of the system, all safety procedures at the operating site, such as maximum speed in each area, must still be observed and caution must be always maintained when driving the vehicle. The operator should be made aware that he/she is, and will remain, responsible for driving the vehicle.

A.M.E. PRODUCER’S DISCLAIMER
A.M.E. is not responsible for the installation of the System and any consequent modifications to the vehicle and the installer is solely responsible for such modifications. In case of installation of the System not in accordance with the instructions and indications provided in the vehicle manufacturer’s manual, A.M.E. will not be responsible for any damage to the vehicle or loss of functionality of the same. In no event shall A.M.E. be liable for any direct or indirect damage of any kind
(including personal injury or property damage) suffered by the Buyer or any third party because of the use of the Product.

ADDITIONAL DIRECTIONS FOR USE: USA AND CANADA
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device contains

TAGSAFETYUWB2

• FCCID 2AQ33-DWM1001
• ICID 23749-DWM1001

LPSUWB001 LPSUWB002

• FCCID UKOLPSUWBBT
• FCCID A8TBM78ABCDEFGH
• ICID 12246A-BM78SPPS5M2

CONNECTIONS

LPSUWB001/LPSUWB002

| Power supply| V=12/24 Vdc Pmax=10W| Protect power supply with 2A ATO fuse
---|---|---|---
| Relay normally open| Max 28V Max 1A| Resistive load
| Isolated input| Max 28V|

TABLET

| | Power supply| V=12-24 Vdc

Pmax=10W

---|---|---|---
| | Ignition command. Positive terminal| ****

V=12-24 Vdc

POSITIONING

Respect right orientation

---|---|---
| ATTACH THE SENSOR TO THE BASE
| CONNECT THE CABLE

VT-7 PRO (AMESPHERE TABLET)
When installing the TABLET and running the connecting cable, care must be taken to ensure that it does not interfere with the movements of the driver and that visibility from the driver’s seat remains unimpaired.

Hereby, Advanced Microwave Engineering s.r.l.declares that the radio equipment type [designation of the type of radio equipment] complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.ameol.it/conformity/amesphere.

www.ameol.it/conformity/amesphere.

Advanced Microwave Engineering S.r.l.

• Head Office: Via Lucca 50-54, 50142 Florence, Italy
• C.F/P.IVA/n. iscr. Reg. Impr. di Firenze 05016620485
• Capitale sociale: € 99.000 i.v.
• T. +39 055 73921
• M. info@ameol.it
• W. www.ameol.it.

References

• SICUREZZA- AME il tuo partner per un posto di lavoro sicuro
• SICUREZZA- AME il tuo partner per un posto di lavoro sicuro
• Amesphere Declaration of Conformity - AME _ REINVENTING PROTECTION

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>