Onysurui M28 M46 Remote Control Drone User Manual
- June 3, 2024
- Onysurui
Table of Contents
Onysurui M28 M46 Remote Control Drone
SAFETY PRECAUTIONS
This product is not a toy and is suitable for experienced RC drone operators aged 1 years and older. It contains small parts and should be kept out of reach of small children.
- The flying zone must be legally approved by your local government.
- Keep your drone away from heat and prolonged exposure to direct sunlight to avoid damage.
- Avoid moisture. Humidity and water can damage your drone, which in turn may cause accidents.
- Please be sure that all the propellers are undamaged and are installed in the correct orientation.
- Please operate your drone as your skill level allows. User fatigue, impairment and improper operation can cause accidents.
- Do not touch propellers, motors or other moving parts while your drone is on.
- Please don’t use this product to follow any moving vehicles.
- Please flight the drone back to you as soon as possible when the battery is running low.
SAFETY PRECAUTIONS
- Please clean this product with a clean dry soft cloth
- Keep your drone away from heat and direct sunlight to avoid damage.
- Keep your drone away from water and damp place to avoid damage.
- Check your drone and battery connections at regular.
BOX CONTENTS
DRONE OVERVIEW
PROPELLERS REPLACEMENT
- Please pull out the propeller that needs to be replaced with the included spanner.
- Please pay attention to the position of the arm corresponding to the A/B propellers. (Refer to the drone overview above)
BATTERY CHARGING
BATTERY INSTALL:
- Please connect the battery to the power port of the drone
- Make sure the power “OFF”, press and hold the button after disconnecting and move the battery to the right to take out.
CHARGING:
****Connect the USB to the battery charging port, and then connect the other port of the USB to the power port($2A). When fully charged, the USB indicator lights up (Charging time is about 120 minutes)
- Do not put the battery in a high temperature and heat place, otherwise, it will be damaged or exploded.
- Never put the battery in water, store it in a dry place.
- Do not disassemble the battery to avoid danger.
- Do not leave it unattended while charging
TRANSMITTER OVERVIEW
- When installing the battery, must make sure the positive and negative poles and the positive and negative poles of the battery box, and do not install them in reverse
- Do not mix old and new batteries.
- Do not mix different kinds of batteries.
FUNCTION
KEY LIFTILAND
1. Place the drone on a flat surface,Press “1-KEY LIFTILAND” (pictured) The
propeller of the drone starts to spin, Push the left stick up and the drone
will fly up
2. With the same button, the drone will land slowly when flying.
ALTITUDE HOLD
Push the left stick up or down to the desired height, then release the left
stick to the center position. The drone will continue to fly at the current
aititude, if you want to change the altitude, please repeat the above steps,
SPEED MODE
- The drone has three speed modes
- Press “speed switch” (pictured)
- The transmitter will “di” three times to indicate in high-speed mode, two “di” are medium speed mode, one “di” is low speed mode.
- Speed mode can also be switched during flight,
LIGHTS MODE
Press’Lights Mode” (pictured) to change different lights.
LOW BATTERY WARNING
When the battery power is low, the lights of the drone will flash during
flight, and the transmitter will issue “didi” reminder, At this point you only
have 30 secondsor so to land the drone.
LOW BATTERY WARNING
Caution: Please flips in a spacious airspace above 2 meters.When the
battery is fully charged, the flips effect is the best, and it is not suitable
to flips in a low power state.
- Long press the “ROLL/FLIP” button (pictured) and the transmitter will make two beeps, indicating that the drone is in the ROLL/FLIP mode.
- Move the directional stick up or down an d the drone will flip up or down.
- Move the directional stick left or right and the drone will flip left or right,
Press the “AUTO ROTATION” (Ppictured) button to activate the auto-rotate
function. To end automatic rotation. iust push anv iovstick
HEADLESS MODE
Headless mode can fly without knowing the direction of the drone. Before
entering headless mode, please set the flying direction of the drone first:
- Turn on the transmitter and drone Press the “Headless Mode” button (pictured) The transmitter will continue to make a “di” sound, The drone lights started flashing.
- Make sure the drone and the transmitter are facing9 forward.
- Press the “Headless Mode” button again, the drone light will remain on, and the transmitter will stop the “di” sound. Now means that the headless mo de has been successfully entered.
( Caution: Do not change the orientation of transmitter after entering Headless Mode. Otherwise, you will lose the set orientation)
READY TO FLY
- Insert the drone battery. Turn on the drone and place it on a flat surface, drone lights will flash quickly.
- Turn on the transmitter, it will “di” once and the light flashes quickly.
- Automatic linking. After the drone and the transmitter match the frequency, the light of the transmitter will normally on.
Now the drone is ready to fly.
Caution: Make sure the drone and transmitter batteries are fully charged
before flight.
FLIGHT CONTROLS
DIRECTION
-
HOVER UP/DOWN
Push the THROTTLE STICK up/down to fly the drone up/down. -
FORWARD/BACKWORD
Push the DIRECTION STICK up/down to fly the drone forward/backward
FLY LEFT-RIGHT
- Move the DIRECTION STICK to the lefuright to fly the drone left/right.
- ROTATE LEFT/RIGHT
Move the THROTTLE STICK to the leftright to rotate the drone left/right.
TRIM ADJUSTMENTS
FORWARD/BACKWARD TRIM
When the drone drifts forward while flying, press and hold the “DIRECTION TIRM” button and push the direction stick down. When the drone drifts forward while flying, press and hold the “DIRECTION TIRM” button and push the direction stick down.
LEFT/RIGHT TRIM
When the drone drifts left while flying, press and hold the “DIRECTION TIRM” button and push the direction stick to the right. When the drone drifts right while flying, press and hold the “DIRECTION TIRM” button and push the direction stick to the left.
TROUBLESHOOTING GUIDE
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>