XunDong XDBB5Z15790A Fits Glass Panel and Sunshade Motors Instruction Manual
- June 1, 2024
- XunDong
Table of Contents
XunDong XDBB5Z15790A Fits Glass Panel and Sunshade Motors
Product Information
Specifications:
- Model: XDBB5Z15790A
- Fits Glass Panel and Sunshade Motors
- Fits Part Numbers: BB5Z-15790-A, BB5Z-15790-D
- Fits 2011-2017 Ford Explorer
Product Usage Instructions
Troubleshooting Guide:
The XunDong Sunroof Motors are located at the front opening of the sunroof. Water exposure due to clogged drain tubes can cause the motor control module to fail. Glass panel motors are more prone to water damage than sunshade motors.
Initialization:
When initializing both sunroof opening panel motors, start with the sliding glass panel motor first. The new motor can only be moved towards the closed position and must be initialized. Initialization of the sunroof motor is necessary when servicing any part of the sunroof opening panel system.
Motor Recalibration Procedure:
- Open the driver or front passenger door.
- Turn the ignition to the ON position.
- Trigger the sunshade control switch until the sun visor is fully closed.
- Within 5 seconds, do the following:
- Cycle ignition OFF and back ON.
- Briefly press the TILT switch for less than 1 second and release.
- Press and hold the TILT switch until the glass panel opens and closes completely (up to 20 seconds).
- Release the switch and verify successful recalibration by testing one-touch open, close, and vent operations.
Please follow these steps to recalibrate the sunroof motor.
Contact our team for further assistance if needed.
FAQ
Q: What should I do if water exposure causes the motor control module to fail?
A: If water exposure leads to motor failure, it is recommended to replace the affected motor promptly to prevent further damage.
Q: Can I use the same recalibration procedure for both glass panel and sunshade motors?
A: Yes, the motor recalibration procedure provided is suitable for both glass panel and sunshade motors.
Troubleshooting Guide for XunDong Sunroof Motors
Model: XDBB5Z15790A
- Fits Glass Panel and Sunshade Motors
- Fits Part Number: BB5Z-15790-A, BB52-15790-D
- Fits 2011-2017 Ford Explorer
The motors are located at the front opening of the sunroof. They can easily get wet when the front drain tubes are clogged, preventing proper drainage. Water exposure causes the motor control module to fail. We see a higher failure rate in the glass panel motors versus the sunshade motors. Both motors are identical, but the location of the glass motor makes it more prone to water damage when drain tubes are blocked.
! NOTE: If both sunroof opening panel motors are initialized simultaneously, the sliding glass panel motor should be initialized first, followed by the other motor.
! NOTE: The new motor can only be moved toward the closed position and must be initialized.
! NOTE: The sunroof motor must be initialized when servicing any part of the sunroof opening panel system.
Motor Recalibration Procedure:
This procedure works for both glass and sunshade motors.
- Open the driver or front passenger door.
- Turn the ignition to the ON position.
- Trigger the sunshade control switch until the sun visor reaches the fully closed position.
- Within 5 seconds, complete the following:
- a) Cycle ignition OFF and back ON.
- b) Briefly press the TILT switch for less than 1 second and release.
- c) Press and hold the TILT switch until the glass panel opens and closes completely. (This can take up to 20 seconds to initiate)
- Release the switch and verify successful recalibration by performing one-touch open, one-touch close, and one-touch vent operations.
Please try recalibrating the sunroof motor according to these prompts. Our team is always available if you need any further assistance.
Documents / Resources
|
XunDong XDBB5Z15790A Fits Glass Panel and Sunshade
Motors
[pdf] Instruction Manual
XDBB5Z15790A Fits Glass Panel and Sunshade Motors, XDBB5Z15790A, Fits Glass
Panel and Sunshade Motors, Panel and Sunshade Motors, Sunshade Motors
---|---