HOUWA SYSTEM DESIGN BLEAD-MOD33QDNA BT Module User Manual
- June 1, 2024
- HOUWA SYSTEM DESIGN
Table of Contents
HOUWA SYSTEM DESIGN BLEAD-MOD33QDNA BT Module
Specifications
- Model: BLEAD-MOD33QDNA
- FCC ID: 2BBG3BLEADMOD33
- Bluetooth Version: Bluetooth Technology
- Data Rate: Not specified
- Operation Frequencies: Not specified
Product Overview:
The BLEAD-MOD33QDNA is a Bluetooth module designed by Houwa System Design
Corp. It features a UART interface, Class 1 Bluetooth power level support,
high-sensitivity Bluetooth receiver, and a Miniature Terminal Mount Monopole
antenna.
Federal Communication Commission Interface Statement:
This device complies with Part 15 of the FCC Rules. It must not cause harmful
interference and must accept any interference received.
Radiation Exposure Statement:
The module complies with FCC mobile radiation exposure limits and should be
installed and operated with a minimum distance of 20cm between the radiator
and the user’s body.
BT Module User Manual
(Model: BLEAD-MOD33QDNA)
FCC ID：2BBG3BLEADMOD33
Notice
- Houwa System Design Corp. reserves the right to change specifications detailed in this document at any time without notice, and assumes no responsibility for any errors within this document.
- This document contains proprietary information in which is the property of the Houwa System Design Corp. and shall not be disclosed to others in whole or in part, reproduced, copied, or used as the basis for design, manufacturing, or sale of apparatus without written permission of Houwa System Design Corp.
Contact in the US ;
- Company Name: Americas Compliance Consulting LLC dba iCertifi
- Address: 1001 SW Disk Drive, Ste 250 Bend, Oregon 97702
- USA e-mail: FCC_sDoC@icertifi.com
BLEAD-MOD33QDA User Manual /Houwa System Desing Corp.
Product Overview
Size
Features
- UART interface
- Class 1 Bluetooth power level supported.
- High-sensitivity Bluetooth receiver
- Miniature Terminal Mount Monopole
| Bluetooth Version | Bluetooth 4.1 |
|---|---|
| Bluetooth Technology | Bluetooth Low Energy |
| Data Rate | 1Mbps/2Mbps |
| Operation Frequencies | 2.402 – 2.480GHz |
Federal Communication Commission Interface Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement:
This equipment complies with radio frequency exposure limits set forth by the
FCC and Industry Canada for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20 cm between the device
and the user or bystanders. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM
Manual v01 guidance, the following conditions must be strictly followed when
using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
List of applicable FCC rules
This module has been tested for compliance to FCC Part 15C
Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any
other usage conditions such as co-location with other transmitter(s) or being
used in a portable condition will need a separate reassessment through a class
II permissive change application or new certification.
Limited module procedures Not applicable.
RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body. If
the module is installed in a portable host, a separate SAR evaluation is
required to confirm compliance with relevant FCC portable RF exposure rules.
Antennas
The following antennas have been certified for use with this module; antennas
of the same type with equal or lower gain may also be used with this module.
The antenna must be installed such that 20cm can be maintained between the
antenna and users.
| Antenna Type | Miniature Terminal Mount Monopole |
|---|---|
| Antenna Connector | RP-SMA(M) |
| Antenna Gain Max | 2.24dBi |
Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2BBG3BLEADMOD33”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition an any
co-located or simultaneous transmission with other transmitter(s) or portable
use will require a separate class II permissive change re-evaluation or new
certification.
Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does
not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement
applicable to the final host. The final host will still need to be reassessed
for compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
IMPORTANT NOTE : in the event that these conditions can not be met (for example co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end ser regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/waning as show in this manual.
OEM/Host manufacture responsibilities
OEM/Host manufactures are ultimately responsible for the compliance of the
Host and Module. He final product must be reassessed against all requirements
of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the
US market. This includes reassessing the transmitter module for compliance
with the Radio and EMF essential requirements of the FCC rules. This module
must not be incorporated into any other device or system without retesting for
compliance as multi-radio and combined equipment.
BLEAD-MOD33QDA User Manual /Houwa System Desing Corp.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>