mumbi m-TG102 Wireless Doorbell User Guide
- June 1, 2024
- mumbi
Table of Contents
mumbi m-TG102 Wireless Doorbell
Product Information
Specifications:
- Product Name: m-TG102 Wireless Doorbell
- Model: Type 23A
- Brand: MUMBI
- Includes: Transmitter, Receiver, Type 23A Battery
Description:
The m-TG102 Wireless Doorbell is a reliable and easy-to-install doorbell
system that includes a transmitter and receiver for seamless communication. It
operates using a Type 23A battery for long-lasting performance.
Features:
- Speaker for audible alerts
- Signal light for visual alerts
- Compact and durable design
- Complies with safety and regulatory standards
Product Usage Instructions
Battery Replacement:
- Open the sender unit by following the manufacturer’s instructions.
- Locate and open the battery compartment on the sender unit.
- Remove the old battery (Type 23A) and replace it with a new one.
- Close the battery compartment securely.
- Close the sender unit properly.
Safety Instructions:
- Avoid direct contact with water. For indoor use only.
- Suitable for outdoor installation.
- Do not immerse the units in water or expose them to high temperatures.
- Use only alkaline batteries to prevent leakage and ensure longer service life.
- Dispose of old batteries in an environmentally friendly manner.
Placement Recommendations:
Avoid placing the units near heat sources, open flames, or liquid-filled
objects. Ensure proper ventilation and suitable mounting locations for optimal
performance.
FAQs (Frequently Asked Questions)
-
Q: Can I use rechargeable batteries with the m-TG102 Wireless Doorbell?
A: It is recommended to use alkaline batteries for better performance and to prevent leakage. Rechargeable batteries may not provide the same longevity. -
Q: How do I test if the doorbell is functioning correctly?
A: Press the doorbell button to check if both the speaker and signal light are activated. Ensure that the battery is properly installed and functional.
Battery Replacement Wireless Doorbell
Product Description
Sliding switch on the backside of the receiver
Safety Instructions
- Avoid direct contact with water. For indoor use only.
- Suitable for outdoor installation.
- The fitting operates using a safety transformer. In case of fault, replace it with a model with the same specifications.
- The fitting is equipped with a fuse.
- Protection class 1: the fitting must be earthed.
- Protection class 2: the fitting is double insulated and does not require earthing.
- Protection class 3: the fitting is suitable only for low voltage, e.g. 12V.
- The detection area has the indicated dimensions.
- There are no serviceable parts in the unit, do not attempt to repair it.
- Do not mount the transmitter onto any metal surfaces or UPVC doorframe, as this will reduce the operation range seriously.
- Do not immerse either unit in water.
- Do not mount either unit close to a fireplace or expose it to high temperatures.
- Do not use different types of batteries in either unit. If leaving the unit for a long period, remove the battery from the compartment to prevent leakage.
- Do not leave exhausted batteries in either unit. If leaving the unit for a long period, remove the battery from the compartment to prevent leakage.
- Always use alkaline batteries as these will give longer service and are less likely to leak.
- Please dispose of old, defective batteries in an environmentally friendly manner by the relevant legislation.
- Make sure that no naked flame sources, such as lighted candles should be placed on the unit.
- The unit should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the unit.
- CAUTION: Replace only with the same or equivalent type of battery that is recommended by the manufacturer.
- CAUTION: Danger of explosion if the battery is incorrectly installed or replaced.
- Ensuring the battery polarity matches the internal markings.
- Operating Temperature
- The operating range is up to…
- Default (factory preset)
- Isolate the wire to the indicated length.
- Where provided, the heat protection sleeve must be used over the full stripped length of the cable.
- The fitting is drip-proof.
- The fitting is rainwater-proof.
- The fitting is splash-proof.
- The fitting is dust-proof and splash-proof.
- The fitting is dust-proof and spray-proof.
- The fitting is dust-tight and splash-proof.
- Warranty Condition
The warranty period can be found on the pictogram on the front of the packaging. If any damage was caused through incompetent use or modifications/repairs carried out by third parties, then the warranty is no longer applicable. Normal wear and tear and consequential loss are not included in the warranty.
DECLARATION OF CONFORMITY
EC DECLARATION OF CONFORMITY
- Company ROOS ELECTRONICS
- Address, City Broekakkerweg 15, 5126 BD PO Box115, 5126 ZJ GILZE
- Country The Netherlands
- Declares that the product:
- Description Wireless doorbell (transmitter + receiver)
- Product number m-TG102
- Trade mark MUMBI
Is herewith confirmed to comply with the requirements set in the Council Directive on the Approximation of the Member States relating to:
- Electro Magnetic Compatibility Directive (2004/108/EC)
- LVD Directive (2006/95/EC)
- R&TTE Directive (1999/5/EC)
- RoHS Directive (2002/95/EC)
Assessment of compliance of the product with the requirements relating to EMC was based on the following standards:
EN 301 489-01 V1.6.1 & EN 301 489-03 V1.4.1
The requirements relating to Electrical Safety were based on the following
standards:
- EN 60065: 2002 +A1: 2006
The requirements relating to RF were based on the following standards:
- EN 300 220-2 V2.1.1
Contact Information
- mumbi · Claus GmbH · Sigsfeldstraße 4 · D-45141 Essen
- Fax: +49 (0)201-21969-428
- Internet: http://www.mumbi.de.