SelectBlinds E-Series 2.5 inch Premier Room Darkening Sheer Shades Instruction Manual

SelectBlinds E-Series 2.5-inch Premier Room Darkening Sheer Shades

Getting Started
NOTE: Your product will come ready to be installed and used without any programming needed. Use the instructions in this guide if there are any issues with your product.

Operating the Remote

• Motorized Wand Instruction Guide
• Single Channel Instruction Guide
• Multi-Channel Instruction Guide

Questions?
Contact your Retail Dealer regarding any questions you may have about your E-SERIES product.
WELCOME TO YOUR E-SERIES PRODUCT WE HOPE YOU ENJOY THE EASE AND FUNCTIONALITY OF YOUR PRODUCT

E-SERIES MOTOR NOTE
The E-SERIES Motor can be found on the headrail of your E-Series Product. If your product will not charge or function properly, remove the product from the window and make sure that all connections to the battery, motor and wand are connected. (Horizontal Fabric E-Series only. Sheerview E-Series is an all-in- one motor/battery)

HORIZONTAL BLIND

SHADE

NOTE
The picture depicts an underside of the shade headrail.

WAKE YOUR E-SERIES PRODUCT
Press, UP DOWN or STOP to wake your product in preparation for setting changes.

SETTING KEYNOTE

The Setting Key can be found on the Motor of the headrail of your E-Series Product (green circular button) and the back of the Motorized Wand (white pinhead button). A paper clip can be used to troubleshoot the function of the product.

• (pg. 3 Wand Instructions)
• (pg. 4 Single Channel Remote Instructions)
• (pg. 6 Multi-Channel Remote Instructions)

If your Motorized Wand is attached, there is a small pinhole Setting Key on the back just above the Micro USB port. Use this in place of the Setting Key in the headrail, as this may be difficult to reach.

COMPLETE RESET OF THE E-SERIES PRODUCT

• Press & Hold the SETTING KEY until the product jolts 4 times a 3-second pause will happen in between jolts, then release.
• You will hear 4 beeps after you release the Setting Key.

TECHNICAL SPECIFICATIONS

• Rated Voltage: 12v
• Micro USB
• Charge port on the back of the wand
• SETTING Key

PROGRAMMING BUTTONS

1. SETTING THE TOP & BOTTOM POSITION
   • SET-TOP POSITION
   • Lower the bottom rail 5” from the top, then Press & Hold UP+STOP (2 jolts & 1 beep) to release the buttons.
   • The motor will be in jog mode, press UP or DOWN to select your preferred top position of your product.
   • Press the STOP Button to set this position. You have successfully set the top position.
   • SET BOTTOM POSITION
   • Go to the desired bottom position, then Press & Hold DOWN+STOP (2 jolts & 1 beep) to release the buttons.
   • The motor will be in jog mode, press DOWN or UP to select the preferred bottom position of your product.
   • Press the STOP button to set this position. You have successfully set the bottom position.
2. CORRECT THE TOP & BOTTOM POSITION
   • Press & Hold UP+STOP (1 jolt & 1 beep) then press the UP and DOWN button to the new desired top position.
   • Press & Hold UP+STOP (1 jolt & 1 beep)to set this position. You have successfully set the corrected top position.
   • CORRECT BOTTOM POSITION
   • Press & Hold DOWN+STOP (1 jolt & 1 beep) then press the DOWN and UP button to the new desired bottom position.
   • Press & Hold DOWN+STOP (1 jolt & 1 beep) to set this position. You have successfully set the corrected bottom position.
3. SWITCH BETWEEN CONTINUOUS MODE & JOG MODE
   • Press & Hold UP+DOWN (1 jolt & 3 beeps), the motor has switched to Jog Mode from Continuous Mode (comes pre-programmed on all E-Seres Products)
   • Repeat the previous step if you want to switch back to Continuous Mode.
4. REVERSE CONTROL DIRECTION
   • Press & Hold the Setting Key on the Wand/Motor (3 jolts) 3-second pause in between each jolt, then release the button. you will hear 3 beeps
   • You have reversed the directions of the UP and DOWN buttons.

TECHNICAL SPECIFICATIONS

• Transmitting Frequency: 433.925MHZ
• Operating Temperature 5˚C – 50˚C / 41˚F – 122˚F

Transmission Distance

• Outside: 200 meters / 656 feet
• Inside: (between 2 walls) 35 meters / 114 feet
• Remote Model Number: DD2700H

PROGRAMMING BUTTONS

1. PAIR A REMOTE

   • Press & Hold the SETTING KEY (pg. 1 Setting Key Note) on the back of the Wand/ Motor (2 jolts & 1 long beep), release the Setting Key, then press UP on the remote to pair.
   • You will have successfully paired the remote when you receive feedback on (2 jolts & 3 beeps).
   • NOTE: The Single Channel Remote can control up to 20 E-SERIES products at one time. See “Pair A Remote” for instructions.

2. DELETE A REMOTE

   • Press & Hold the SETTING KEY (pg. 1 Setting Key Note) on the back of the Wand/ Motor (2 jolts & 1 long beep), release the Setting Key, then press DOWN on the remote to delete.
   • You will have successfully deleted the remote when you receive feedback on (2 jolts & 5 beeps).

3. ADJUST THE SPEED OF YOUR PRODUCT

   • There are three speed levels (3-high, 2-medium, 1-slow) your product comes set at speed level 3-high.
   • Slow down the product speed, Press P2 then DOWN 2 times (you will hear the drop in motor speed at each level 2-medium, 1-low).
   • Speed up the product speed, Press P2 then UP 2 times (you will hear the rise in the motor speed at each level 2-medium, 3-low).
   • You will have successfully slowed down or speed up your product when you receive (2 jolts and 1 beep).

4. SETTING THE TOP & BOTTOM POSITION

   • SET-TOP POSITION

   • Go to the desired top position, then Press & Hold UP+STOP (4 jolts & one beep) and release the buttons.

   • The motor will be in jog mode, press UP or DOWN to select your preferred top position of your product.

   • Press the STOP Button to set this position. You have successfully set the top position.
     SET BOTTOM POSITION

   • Go to the desired bottom position, then Press & Hold DOWN+STOP (4 jolts & one beep) and release the buttons.

   • Inside the Back of the Remote Next Page –

   • Correct the Top & Bottom Position

   • Switch between Continuous Mode & Jog mode

   • Reverse control direction

   • Complete a reset of the E-SERIES Product

   • The motor will be in jog mode, press DOWN or UP to select your preferred bottom position of your product.

   • Press the STOP Button to set this position. You have successfully set the bottom position.

5. CORRECT THE TOP & BOTTOM POSITION

   • Press & Hold UP+STOP (2 jolts & 1 beep) then press the UP and DOWN button to the new desired top position.
   • Press & Hold UP+STOP (2 jolts & 1 beep to set this position. You have successfully set the corrected top position.
   • CORRECT BOTTOM POSITION
   • Press & Hold DOWN+STOP (2 jolts & 1 beep) press the DOWN and UP buttons to the new desired bottom position.
   • Press & Hold DOWN+STOP (2 jolts & 1 beep to set this position. You have successfully set the corrected bottom position.

6. SWITCH BETWEEN CONTINUOUS MODE & JOG MODE

   • Press & Hold UP+DOWN (2 jolts & 1 beep) the motor has switched to Jog Mode from Continuous Mode (comes pre-programmed on all E-Seres Products)
   • Repeat the previous step, if you want to switch back to Continuous Mode.

7. REVERSE CONTROL DIRECTION

   • Press & Hold the SETTING KEY on the Wand/Motor (4 jolts) then release the button.
   • You will have reversed the directions of the UP and DOWN buttons.

TECHNICAL SPECIFICATIONS

• Transmitting Frequency: 433.925MHZ
• Operating Temperature  5˚C – 50˚C / 41˚F – 122˚F
• Outside: 200 meters / 656 feet
• Inside: (between 2 walls) 35 meters / 114 feet
• Remote Model Number: DD2702H

PROGRAMMING BUTTONS

1. PAIR A REMOTE
   • Select the channel you want to pair by pressing LEFT < or > RIGHT.
   • Press & Hold the Setting Key (pg. 1 Setting Key Note) on the back/top of the Wand/Motor (1 jolt, release the Setting Key, and you will hear 1 long beep), then press P2 once, you will hear a beep, then press UP on the remote to pair.You will have successfully paired your Multi-Channel Remote when you receive 1 jolt and 3 beeps.
2. ADD ANOTHER CHANNEL FOR A NEW E-SERIES PRODUCT
   • Press the LEFT < and > RIGHT buttons at the same time, the LCD will show a C, and then turn into 15. DO NOT let go of the buttons until you see the 15.
   • Change the channel by pressing < or > Press STOP at the desired number of channels you need.
   • NOTE: Channel “0” controls all Products on the Multi-Channel Remote.
   • NOTE: The Multi-Channel Remote can support up to 20 products per channel and up to 15 channels per remote.
3. DELETE A REMOTE
   • Press & Hold the Setting Key (pg. 1 Setting Key Note) on the back of the Wand/Motor (2 jolts & 1 long beep), release the Setting Key, then press DOWN on the remote to delete.
   • You will have successfully deleted the remote when you receive feedback of (1 jolt & 5 short beeps)
4. ADJUST THE SPEED OF YOUR PRODUCT
   • There are three speed levels (3-high, 2-medium, 1-slow) your product comes set at speed level 3-high.
   • Slow down the product speed, Press P2 then DOWN 2 times pause for 1 second in between DOWN presses (you will hear the drop in motor speed at each level 2-medium, 1-low).
   • Speed up the product speed, Press P2 then UP 2 times pause for 1 second in between UP presses (you will hear the rise in motor speed at each level 2-medium, 3-low).
   • You will have successfully slowed down or sped up your product when you receive (2 jolts and 1 beep)
   • Inside the back of the remote

DOWN CHANNEL CYCLE

SEE Motorized Wand (pg.3) /Single Channel Remote (pg.4-5)

• Set the Top & Bottom Position (pg.3 / pg.4)
• Correct the Top & Bottom Positions (pg.3 / pg.4)
• Switch between Continuous Mode & Jog mode (pg.3 / pg.5)
• Reverse control direction (pg.3 / pg.5)
• Complete reset of the E-SERIES Product (pg.3)

WARNING
THE E-SERIES PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING CARBON BLACK (CAS NO. 1333-86-4) WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER. FOR MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV

References

• P65WARNINGS.CA.GOV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>