SelectBlinds 78236-00 Aluminum Blind Installation Guide

SelectBlinds 78236-00 Aluminum Blind

Product Specifications

• 1 Blind
• 2 Wand
• 3 Brackets/Screws
• 4 Cordless Handle(s)
• 5 Optional Hold-down Brackets
• 6 Optional Extension Brackets
• 7 Optional Side-mount Brackets

Product Usage Instructions

Installation Steps

1. Determine the desired location and height for the blind.
2. Optional: For blinds 60 inches or less, assemble optional side-mount brackets.
3. Ensure the installation surface is flat and level.
4. Measure 3 inches from the blind edge on both ends and mark the locations.
5. Mark screw locations and center additional brackets across the width if needed.
6. Pre-drill pilot holes using a 1/16 drill bit for wood surfaces or 3/32 drill bit for metal surfaces.
7. Mount the blind into the brackets by hooking the back lip on the headrail to the bottom of the bracket and rolling the headrail back into place until it snaps.
8. Screw the brackets securely into place.
9. Attach headrail brackets to extension brackets using provided screws and nuts.
10. Clip the handle(s) to the center of the bottom rail. For wider blinds, attach two handles spaced apart at the center.
11. Optional: Install hold-down brackets for added stability.

Blind Operation
To open or close the slats

• Rotate the wand right or left for desired light control and privacy.
• Pull out the wand at an angle for smooth operation. Avoid rotating with the wand straight down.
• To open or close the slats, simply rotate the wand accordingly.

Frequently Asked Questions (FAQ)

• Q: How do I clean the blind?
  A: To clean the blind, use a feather duster or a microfiber cloth to gently wipe off dust and debris. For deeper cleaning, lightly dampen a cloth with a mild detergent solution and wipe down the slats. Avoid using harsh chemicals or abrasive cleaners.

• Q: Can I trim the blind to fit my window?
  A: It is not recommended to trim the blind. Altering the size of the blind may affect its functionality and structural integrity. It’s best to choose a blind that fits your window dimensions appropriately.

HOW TO INSTALL

Inside-, ceiling-, or outside-mount cordless aluminum blinds

1. Everything needed to install your blind
2. Blind
3. Wand
4. Brackets/Screws
5. Cordless Handle(s)
6. Optional Hold-down Brackets
7. Optional Extension Brackets
8. Optional Side-mount Brackets Bracket chart
   Ordered width Bracket quantity.

  * Less than or equal to 42″ • Hasta 106.7 cm 2
  * Less than or equal to 72″ • Hasta 182.9 cm 3
  * Less than or equal to  102″ • Hasta 259.1 cm 4
  * Less than or equal to  132″ • Hasta 335.3 cm 5
  * Less than or equal to144″ • Hasta 365.9 cm  6  

Tools needed

2. Determine inside/ceiling, Determine inside/ceiling, outside or side mountoutside, or side mount

3. Place blind in desired location, mark corners Brackets and blinds must be installed on a flat and level surface.

4. Measure 3″ in from blind edge on both ends and mark
   

5. Mark screw locations; center additional brackets across width of the blind, if applicable

6. Drill pilot holes
   Use 11⁄1616″ drill bit for wood mounting surface. 33⁄3232″ drill bit for metal. For other mounting surfaces, use appropriate wall anchors and drill the correct size hole per the anchor instructions.
   

7. Screw brackets into place Optional extension brackets: assemble brackets
   Attach headrail brackets to extension brackets using screws and nuts.

8. Mount blind into brackets
   Hook the back lip on the headrail to the bottom of the bracket and then roll the headrail back into the bracket until you hear it snap into place.

9. Attach cordless handle(s)
   Clip handle to center of bottomrail. For blinds over 48″ wide, attach two handles, shoulder width apart at center.

   • Optional: mount hold-down brackets

10. Blind operatio n: Opening and closing the slats
    Close or open the slats by rotating the wand right or left for desired light control and privacy. Wand must be pulled out at an angle when rotating for smooth operation. If operating with the wand straight down, it will be difficult to rotate and you may hear clicking noises.

11. Blind operation : Raising and lowering
    Always raise and lower with slats tilted open. To lower blind, simply pull down using the bottomrail handle. To raise the blind, simply guide the blind to the desired position by gently lifting the bottomrail. On inside mount blinds, the blind may need to be pulled away from the window slightly in order to fully lower the blind.

    • Blind removal
      For blind removal insert a flat head screwdriver between the back of the headrail and the metal tab on the bottom of the mounting bracket. Rotate the screwdriver until the bracket disengages from the lip on the back of the headrail.

Cleaning instructions

• Use warm water and mild non-abrasive liquid soap to clean slats.
• Use a feather duster to remove dust from slats.
• Or, use the brush attachment of a vacuum to remove dust from slats.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>