Delipu AZ-1121L Fan Lamp Instruction Manual

Delipu AZ-1121L Fan Lamp

Product Information

Specifications:

• Power: AC 110-120V, 60Hz
• Remote Control Range: 30 feet (10 meters)
• Batteries: Requires two 1.5V AAA batteries (not included)

Product Usage Instructions

Installation:

Wiring and Hanging:

1. Ensure the power is cut before working with the wiring.
2. Use the wire nuts provided with your fan to connect wires securely.
3. Hook the safety rope latch on the mounting plate to the fan engine to prevent falls.
4. Connect wires following these steps:
   • a. Connect the 2 colored wires of the main power plug to the identically colored wires from the junction box.
   • b. Connect the green or bare copper ground wire from the junction box to the fan’s green ground wire.
5. Align the fan host with the four screws on the hanging plate and tighten the screws.

Remote Control Operation:

The remote control operates within a range of 30 feet using two 1.5V AAA batteries (not included). If not in use for a prolonged period, it is recommended to remove the batteries for better service life. If needed, install the remote control holder onto a wall or any suitable flat surface using appropriate fasteners. Use steel screws and plastic anchors for wood or weaker surfaces, and anchor bolts for reinforced concrete or similar surfaces.

Key:

• 1-6: Fan Speed Levels
• R: Reverse Fan Direction
• O: Turn Off Fan
• F: Turn On Fan
• + / -: Adjust Fan Speed

Frequently Asked Questions

• Q: How do I change the batteries in the remote control?
  • A: To change the batteries, locate the battery compartment on the back of the remote control, remove the cover, and replace the old batteries with two new 1.5V AAA batteries. Ensure correct polarity when inserting the batteries.
• Q: Can I use LED bulbs with this fan?
  • A: Yes, you can use LED bulbs compatible with standard E26 sockets. Ensure the wattage of the LED bulbs does not exceed the maximum wattage recommended for the fan.
• Q: How do I clean the fan blades?
  • A: Use a soft, damp cloth to wipe the fan blades. Avoid using abrasive cleaners or solvents as they may damage the finish. Ensure the fan is turned off before cleaning.

SAFETY INFORMATION

Warning

• To reduce the risk of electric shock, ensure electricity has been turned off at the circu仆 breaker o「fuse box before beginning.
• All wiring MUST be in acco「dance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician
• This fan is suitable for use with solid-state speed controls.
• To reduce the risk of personal injury, ONLY use the fasteners provided with the junction box for mounting to the Junction box. Most Junction boxes commonly used for the support of lighting fixtures are NOT acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
• TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, & PERSONAL INJURY, MOUNT
• THE FAN TO A JUNCTION BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”
• The junction box and support structure MUST be securely mounted to create a level surface worth 1 O” of horizontal and MUST be capable of reliably supporting a minimum of 50 pounds (23 kg). ONLY use UL-listed junction boxes marked” FOR FAN SUPPORT”
• After electrical connections are completed, spliced conductors should be turned upward and pushed ca「efully up into the junction box. The wires should be spread apart with lhe grounded conductor and the equipment-grounding conductor on one side of the junction box
• The fan MUST be mounted with a minimum clea「ance of 7 feet (2.5 m) from the tra由ng edge of the blades to the floor
• DO NOT use the reverse switch while the fan blades are in motion. To prevent damage and ensure long use, lhe fan MUST be turned off and the blades stopped befo「e reversing direction
• DO NOT place objecls in the palh of the blades
• Exercise caution when working around or cleaning the fan
• Use a soft dry cloth to clean the fan body and blades. DO NOT use water o「detergent
• The electrical diagrams provided herein are for reference only. Light kits that are not packaged with the fan MUST be UL-listed and suitable for use with this fan. Switches MUST be UL general-use switches. Refer to their separate instructions for proper assembly

INTRODUCTION

Before beginning the installation of this product,  refer to the Parts Diagram on Page 2 and ensu「e all parts are present and display no defects If any part 1s missing or damaged, contact customer service and do not attempt to install the product Read all of the safety information on before installation or use Estimated assembly time 120 minutes Additional tools required for assembly: Electrical tape, flathead &  screwdriver, power screwdriver, adjustable wrench, pliers, wire strippers, safety glasses, and ladder

Additional helpful tools: AC tester light, tape measure, wiring handbook, and wire cutters

PARTS DIAGRAM

PREPARATION

Turn off Your Power

Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed.

Warning

Failure to disconnect the power supply prior to installation may result in serious injury or death.

Choose Your Mounting Position

If you need to install a new UL listed junction box, secure it directly to your building’s structure using appropriate fasteners and materials.

Caution

DO NOT use plastic boxes. The junction box and its supports MUST be able to support the MOVING weight of the fan (at least 50 lb. or 23 kg) and be rated for fan support. The junction box should create a level surface for the fan that is NOT sloped greater than 10 degrees from horizontal in any direction.

Choose a Suitable Location

Ensure the blades will be at least 30 inches (76 cm) from any obstruction and at least 7 feet (2.5 m) above the floor. In locations without a ceiling joist, a hanger support bar may be required.

Caution

DO NOT install in damp locations.

INSTALLATION

Mounting Bracket

1. Take out the fan body from the package
2. Loosen the four screws on the plate, then turn the plate counterclockwise and remove it

Mounting Bracket

1. Pass your building’s supply wires through the central hole of the mounting bracket.
2. Secure the mounting bracket to your junction box with appropriate fasteners.
   • For wood or other thinner and weaker ceilings:
   • a. Partially fasten the bracket with the mounting bolts and M4 spring & flat metal washers.
   • b. Use the mounting screws and M5 spring & flat metal washers to secure the bracket into place.
   • c. If necessary, drill holes and insert matching plastic anchors (not included) to hold the mounting screws beforehand.
   • For reinforced concrete or similar ceilings, use anchor bolts (not included).

Wiring and Hanging

Warning

Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan. Ensure there are no loose wires or connections and secure connectors with electrical tape.

1. Hook the safety rope latch on the mounting plate to the fan engine to ensure that the fan engine will not fall
2. Connect the wires and secure each set with the provided wire nuts, ensuring they are securelyfastened by gently tugging on each connection.
   • a. Connect the 2 colored wires of the main power plug to the 2 identically colored wires from the junction box.
   • b. Connect the green or bare copper ground wire from the junction box to the fan’s green ground wires.
3. After aligning the fan host with the four screws on the hanging plate along the four holes in the Canopy, turn the fan host clockwise and tighten the four screws

REMOTE CONTROL OPERATION

This remote operates within a range of 30 feet (10 m) using two 1.5V AAA batteries (not included). If the remote will not be used for a prolonged period, it is recommended to remove the batteries for better service life. If needed, install the remote control holder onto a wall or any other suitable flat surface using appropriate fasteners. For wood or other thinner and weaker surfaces, use the provided steel screws and plastic anchors. For reinforced concrete or similar surfaces, use anchor bolts for best results.

Caution

• DO NOT press F/R to reverse the fan’s direction while the fan is  turning.
• Wait for the fan to stop completely before changing the direction of its rotation.

USE DEDICATED APP CONTROL

Downloads and connections

1. Use the APP store, search for “Fan lamp Pro” app to download and install
2.  Scan the QR code here, go to the website and select the download method you want to install

Fan Lamp Pro connection and use

1. Open the Fan Lamp Pro APP and go to the home page
2. Click the cross button below to enter the naming page, enter the name you want to create and select the corresponding room, then click “Confirm”
3. Go to the created page, power on the fan, and press the ” ” button at the same time within five seconds. If the indicator blinks continuously, the connection is successful

Feature

TROUBLESHOOTING

Caution

DO NOT bend the blade during ANY of the following procedures

Maintenance And Cleaning

1. Periodically cleaning your ceiling fan is the only required maintenance. Use a soft brush or lint free cloth to avoid scratching the paint. Please turn off the electricity power before you clean your fan.
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades or even evoke an electrical shock.
3. The motor has permanently lubricated ball bearing. No need to oil

NOTE: MAKE SURE THE POWER IS OFF IN THE ELECTRICAL PANEL BOX BEFORE YOU DO ANY CLEANING OR REPAIRS

Electrical products should not be disposed of with household products. In the EU and UK, according to the European Directive 2012/19/EU for the disposal of electrical and electronic equipment and its implementation in national laws, used electrical products must be collected separately and disposed of at the collection points provided for this purpose. Locations in Australia, Canada, and the United States may have similar regulations. Contact your local authorities or dealer for disposal and recycling advice.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions,maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures or relocate the receiving antenna-Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator and your body.

• If you have any question about the products and installation,
• Pis feel free to contact us this
• Email: iceilfan@outlook.com
• We will solve for you within 24H, Thanks for your support!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>