HILTI W2V2-MQJT-Q21X-RT73 Plus Rotary Instruction Manual
- June 1, 2024
- HILTI
Table of Contents
HILTI W2V2-MQJT-Q21X-RT73 Plus Rotary
WARNING
- Contains: Methacrylates (A), 4-tert-butylpyrocatechol (A), dibenzoyl peroxide (B) May cause an allergic skin reaction. (A,B) Causes serious eye irritation (A) Harmful to aquatic life with long-lasting effects. (A) Very toxic to aquatic life with long-lasting effects. (B)
- W2V2-MQJT-Q21X-RT73 (A)8N43-7QKH-C21E-WXGJ (B)
Adhesive anchoring system for anchor fastenings in hollow and solid masonry. Read the safety precautions, safety data sheet, and product information before use. Read the safety precautions and the product information of the accessories before use.
WHAT IN THE BOX
OVERVIEW
- Hollow brick
- Solid brick
- Render/ stucco or other non-load-bearing layers on hollow brick or block
- Render/ stucco or other non-load-bearing layers on solid brick or block
- Load-bearing layer (e.g., strong plaster) on solid brick
- Temperature of base material
- Push-through installation
- Dry base material
- Water-saturated base material
- Technical data
- Trigger pulls
- Rotary drilling
- Hammer drilling
- Working time
- Curing time
USING INSTRUCTION
INSTALLATION INSTRUCTION
Adhesive anchoring system for anchor fastenings.
Adhesive anchoring system for anchor fastenings in hollow and solid clay
brick, sand-lime block, concrete, concrete block, aerated concrete and natural
stone.
Hilti HIT-HY 270
Contains: methacrylates (A), 4-tert-butyl pyrocatechol (A), dibenzoyl
peroxide (B)
Warning
W2V2-MQJT-Q21X-RT73 (A) / 8N43-7QKH-C21E-WXGJ (B)
- H317 May cause an allergic skin reaction. (A,B)
- H319 Causes serious eye irritation. (A)
- H410 Very toxic to aquatic life with long lasting effects. (B)
- H412 Harmful to aquatic life with long lasting effects. (A)
- P262 Do not get in eyes, on skin, or on clothing.
- P280 Wear protective gloves/protective clothing/eye protection.
- P302+P352 IF ON SKIN: Wash with plenty of soap and water.
- P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
- P337+P313 If eye irritation persists: Get medical advice/attention.
Disposal considerations
Empty packs
- EAK waste material code: 150102 plastic packaging
Full or partially emptied packs:
- Must be disposed of as special waste by official regulations. EAK waste material code: 08 04 09 waste adhesives and sealants containing organic solvents or other dangerous substances. or EAK waste material code: 20 01 27 paint, inks, adhesives and resins containing dangerous substances.
- Content: 330 ml / 11.1 fl.oz. 500 ml / 16.9 fl. oz
- Weight: 540 g/19.0 oz 820 g/28.9 oz
Hilti accepts no liability for damage or failure caused by:
- Storage and transport not by the specified conditions.
- Failure to observe the instructions for use and setting data, incorrect use
- Inadequate design of the anchor points, inadequate load-bearing capacity of the base material
- Other influences of which Hilti is not aware or on which Hilti has no influence, e.g. use with products from a third party.
Product Information
- Always keep these instructions together with the product even when given to other persons.
- Check expiration date: See imprint on foil pack manifold (month/year). Do not use expired products.
- Foil pack temperature during usage: between +5 °C and 40 °C / 41 °F and 104 °F.
- Base material temperature at the time of installation: between –5 °C and 40 °C / 23 °F and 104 °F. Exception in solid clay brick: between +5 °C and 40 °C / 41 °F and 104 °F.
- Conditions for transport and storage: Keep in a cool, dry and dark place between 5 °C and 25 °C / 41 °F and 77 °F.
- For any application not covered by this document / beyond the values specified, please contact Hilti.
- Partly used foil packs must remain in the cassette and have to be used within 4 weeks. Leave the mixer attached on the foil pack manifold and store within the cassette under the recommended storage conditions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive.
NOTICE
Improper handling may cause mortar splashes.
- Always wear safety glasses, gloves and protective clothes during installation.
- Never start dispensing without a mixer properly screwed on.
- Attach a new mixer prior to dispensing a new foil pack (ensure snug fit).
- Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not modify the mixer in any way.
- Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes).
Poor load values / potential failure of fastening points due to inadequate borehole cleaning and setting.
- The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants before adhesive injection.
- For blowing out the borehole – blow out with oil-free air until the return air stream is free of noticeable dust.
- For brushing the borehole – only use a specified steel wire brush. The brush must resist insertion into the borehole – if not the brush is too small and must be replaced.
- If no significant resistance is felt over the entire depth of the hole when drilling (e.g. in unfilled butt joints), the anchor should not be set at this position
- For applications under seismic actions, non-bearing layers have to be removed.
Borehole filling in solid masonry and concrete: Ensure that boreholes are
filled from the back of the borehole without forming air voids. If necessary
use the accessories/extensions to reach the back of the borehole. In the event
of drilling into a cavity, either use HIT-SC or check loads with on-site
testing according to TR 053. For overhead applications use the overhead
accessories HIT-SZ and take special care when inserting the fastening element.
The excess adhesive may be forced out of the borehole. Make sure that no
mortar drips onto the installer.
Borehole filling in hollow masonry: Use HIT-SC mesh sleeve. Fill the mesh
sleeve with mortar from the centring cap until mortar escapes at the centring
cap (filling control).
Note: Hilti HIT-HY 270 is not tested for use with climbing anchors. Applications of this kind are carried out at the user’s own risk.
Not adhering to these setting instructions can fail fastening points!
- 21 Hilti Corporation,LI-9494 SchaanHilti Werke2873-CPR-201-7ETA-13/1036Notified Body 2873ETAG 029 www.hilti.group
- 21 Hilti Corporation, LI-9494 Schaan Hilti Werke 2873-CPR-201-49 ETA-19/1060 Notified Body 2873 EAD 330076-00-0604 www.hilti.group
- 22 Hilti Corporation,LI-9494 SchaanHilti Werke2873-CPR-201-79ETA-22/0395Notified Body 2873EAD 330076-01-0604-01Mental injection anchor for use in masonry www.hilti.group
- 24 Hilti Corporation, LI-9494 Schaan Hilti Plants UK 0836-CPR-23/P6983 UKTA-23/6693 Approved Body 0836 UKAD 330076-00-0604 Bonded injection anchor for use in concrete www.hilti.group
Made in Germany Hilti = registered trademark of Hilti Corporation, Schaan, Liechtenstein www.hilti.group 2023 Right of technical changes reserved S.E. & O
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>