HILTI HIT-HY 270 Chemical Anchors Instruction Manual
- June 1, 2024
- HILTI
Table of Contents
HILTI HIT-HY 270 Chemical Anchors
WARNING
- Contains : methacrylates (A), 4-test-butyl pyro-catechol (A), dibenzoyl peroxide (B)
- May cause an allergic skin reaction. (A, B) Causes serious eye irritation. (A) Very toxic to aquatic life with long-lasting effects. (B)
- Harmful to aquatic life with long-lasting effects. (A)
Specifications
- Product Name: Hilti HIT-HY 270
- Contains: methacrylates, 4-tert-butyl pyro-catechol, dibenzoyl peroxide
- Warnings: May cause allergic skin reaction, serious eye irritation, toxic to aquatic life with long-lasting effects
Product Usage Instructions
Preparation
- Ensure the surface is clean and free of debris.
- Check compatibility with the base material.
Application
- Use the appropriate drilling method based on the base material.
- Insert the Hilti HIT-HY 270 cartridge into the dispensing tool.
- Dispense the product into the drilled hole while ensuring full coverage.
Curing
- Allow the product to cure for the recommended time before subjecting it to load.
- Follow the curing time guidelines provided in the manual.
WARNING
- Contains: methacrylates (A), 4-tert-butyl pyro-catechol (A), dibenzoyl peroxide (B)
- May cause an allergic skin reaction. (A,B) Causes serious eye irritation. (A) Very toxic to aquatic life with long-lasting effects. (B) Harmful to aquatic life with long-lasting effects. (A)\
INFORMATION
- Hollow brick;
- Solid brick;
- Render/ stucco or other non-load-bearing layers on hollow brick or block;
- Render/ stucco or other non-load-bearing layers on solid brick or block;
- Temperature of base material;
- Dry base material;
- Water-saturated base material;
- Hammer drilling;
- Rotary drilling;
- Hammer drilling;
- Working time;
- Curing time
INSTALLATION
Adhesive anchoring system for anchor fastenings
Adhesive anchoring system for anchor fastenings in hollow and solid clay
brick, sand-lime block, concrete, concrete block, aerated concrete and natural
stone.
Hilti HIT-HY 270
Contains: methacrylates (A), 4-tert-butyl pyrocatechol (A), dibenzoyl
peroxide(B)
WARNING : May cause an allergic skin reaction. (A,B) | Causes serious eye irritation.
- (A) | Very toxic to aquatic life with long-lasting effects.
- (B) | Harmful to aquatic life with long-lasting effects.
- (A) | Do not get in the eyes, on the skin, or clothing.
- Wear protective gloves/protective clothing/eye protection
- IF ON SKIN: Wash with plenty of soap and water.
- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- If skin irritation or rash occurs: Get medical advice/attention.
- If eye irritation persists: Get medical advice/attention.
Disposal considerations: Empty packs: EAK waste material code: 150102 plastic packaging
- Full or partially emptied packs: Must be disposed of as special waste under official regulations.
- EAK waste material code: 08 04 09 waste adhesives and sealants containing organic solvents or other Warningous substances. or EAK waste material code: 20 01 27 paint, inks, adhesives and resins containing Warningous substances.
- Content: 330 ml / 11.1 fl.oz; 500 ml / 16.9 fl.oz
- Weight: 540 g / 19.0 oz; 820 g / 28.9 oz
- Hilti accepts no liability for damage or failure caused by: Storage and transport not under the specified conditions.
- Failure to observe the instructions for use and setting data, incorrect use
- Inadequate design of the anchor points, inadequate load-bearing capacity of the base material
- Other influences of which Hilti is not aware or on which Hilti has no influence, e.g. use with products from a third party.
- Product Information: Always keep these instructions together with the product even when given to other persons.
- Check expiration date: See imprint on foil pack manifold (month/year). Do not use expired products.
- Foil pack temperature during usage: +5 °C to 40 °C / 41 °F to 104 °F.
- The base material temperature at time of installation: -5 °C to 40 °C / 23 °F to 104 °F.
- Exception in solid clay brick: +5 °C to 40 °C / 41 °F to 104 °F.
- Conditions for transport and storage: Keep in a cool, dry and dark place between +5 °C to 25 °C / 41 °F to 77 °F. |For any application not covered by this document / beyond the values specified, please contact Hilti.
- Partly used foil packs must remain in the cassette and have to be used within 4 weeks. Leave the mixer attached to the foil pack manifold and store it within the cassette under the recommended storage conditions.
- If reused, attach a new mixer and discard the initial quantity of anchor adhesive.
NOTICE
Improper handling may cause mortar splashes. Always wear safety glasses, gloves and protective clothes during installation.
- Never start dispensing without a mixer properly screwed on.
- Attach a new mixer before dispensing a new foil pack (ensure a snug fit).
- Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not modify the mixer in any way.
- Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes).
Poor load values / potential failure of fastening points due to inadequate borehole cleaning and setting. The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants before adhesive injection.
- For blowing out the borehole – blow out with oil-free air until the return air stream is free of noticeable dust.
- For brushing the borehole – only use a specified steel wire brush.
- The brush must resist insertion into the borehole – if not the brush is too small and must be replaced.
If no significant resistance is felt over the entire depth of the hole when drilling (e.g. in unfilled butt joints), the anchor should not be set at this position
Borehole filling in solid masonry and concrete: Ensure that boreholes are filled from the back of the borehole without forming air voids. If necessary use the accessories/extensions to reach the back of the borehole. HIT-SC is used in the event of drilling into a cavity
- For overhead applications use the overhead accessories HIT-SZ and take special care when inserting the fastening element.
- The excess adhesive may be forced out of the borehole. Make sure that no mortar drips onto the installer.
- Borehole filling in hollow masonry: Use HIT-SC mesh sleeve. Fill the mesh sleeve with mortar from the centring cap until mortar escapes at the centring cap (filling control).
Note: Hilti HIT-HY 270 is not tested for use with climbing anchors. Applications of this kind are carried out at the user’s own risk.
Not adhering to these setting instructions can fail fastening points!
Hilti HIT-HY 270 is subject to approvals from building authorities. This IFU
might contain specific application conditions/situations going beyond the
scope of respective approval. For approval compliant installation of the
product prescription in the approval document takes precedence.
Hilti Corporation,
- LI-9494 Schaan
- Hilti Werke
- 2873-CPR-201-7
- ETA-13/1036
- Notified Body 2873
- ETAG 029
- www.hilti.group
Hilti Corporation,
- LI-9494 Schaan
- Hilti Werke
- 2873-CPR-201-49
- ETA-19/0160
- Notified Body 2873
- EAD 330076-00-0604
- www.hilti.group
Made in Germany
- Hilti = registered trademark of
- Hilti Corporation, Schaan, Liechtenstein
www.hilti.group
© 2024 Right of technical changes reserved S.E. & O
FAQs
- Q: Is Hilti HIT-HY 270 safe for aquatic environments?
- A: No, Hilti HIT-HY 270 is harmful to aquatic life with long-lasting effects. Avoid direct contact with water bodies.
- Q: How should I store unused Hilti HIT-HY 270 cartridges?
- A: Store the cartridges in a cool, dry place away from direct sunlight and sources of heat to maintain product integrity.
- Q: Can I use Hilti HIT-HY 270 for overhead installations?
- A: Yes, Hilti HIT-HY 270 can be used for overhead installations following proper safety precautions and guidelines.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>