PRO1 TECHNOLOGIES R250W Wireless Outdoor Sensor Installation Guide
- June 1, 2024
- Pro1 Technologies
Table of Contents
PRO1 TECHNOLOGIES R250W Wireless Outdoor Sensor
Specifications
- Model: R250W
- Manufacturer: Pro1 Technologies
- Batteries: 2 AA batteries required
- Wireless System Compatibility: PROsyncTM T755WHO thermostat
Installing Batteries
To install 2 AA batteries, remove the cover of the front housing and insert
batteries as shown. Mounting the Outdoor Remote Sensor
To mount the outdoor remote sensor, remove the front cover and place a screw
in the left and right screw holes. For optimal performance, install on a
north-facing wall sheltered by a roof overhang.
Outdoor Sensor and User Guide
Pro1 Technologies
- P.O. Box 3377 Springfield, MO 65804
- Toll Free : 888-776-1427
- Web: www.pro1iaq.com
- Hours of Operation: M-F 9AM – 6PM Eastern
The R250W requires the PROsync™ Wireless System T755WHO thermostat.
Caution: Equipment Damage Hazard
Do not operate the cooling system if the outdoor temperature is below 50˚F
(10˚ C) to prevent possible compressor damage.
Una version en espanol de este manual se puede descargar en la pagina web de
la compania.
Specifications
- Operating Temperature …………………. -40˚F to 140˚F (-40˚C to 60˚ C)
- Operating humidity…………………………. 90% non-condensing maximum
- Dimensions of sensor …………………….. 3.875”W x 3.875”H x 1.125”D
Installing Batteries
To install 2 AA batteries remove the cover of the front housing and insert batteries as show below.
NOTE About Low Batteries
When the outdoor battery needs to be changed the Main Thermostat will flash
OUTDOOR LO BAT as seen above. When OUTDOOR LO BAT appears, user has ~3 months
to change the batteries.
Battery types
- Alkaline AA batteries will perform well in most applications.
- Lithium AA primary cell batteries are recommended for cold climates. See the battery manufacturer product specifications for details.
- Rechargeable batteries are not recommended.
Mounting the Outdoor Remote Sensor
To install remove the front cover and place a screw in the left and right screw holes.
IMPORTANT
For best results, install on a north-facing wall, sheltered by a roof overhang
or something similar. Do not install in direct sunlight.
Installation Tips
Before putting the inside cover back on, proceed to the next page to establish a connection between the Equipment Module and the Outdoor Sensor.
Connecting to the Main Thermostat
The Outdoor Sensor must be paired to a PROsync Equipment Module (sold seperately)
On the Equipment Module
-
Press the PAIR button below the LED.
- The equipment module will begin double blinking pink for 2 minutes while it waits for a remote to join.
-
Press the button on the inside of the outdoor remote sensor. The LED on the outdoor remote sensor will begin to flash pink.
-
When the equipment module receives the pairing message , it will blink blue repeatedly, then return to blinking green.
-
The outdoor remote sensor will blink green 10 times when it is paired, then the LED on the outdoor sensor will turn off.
Checking outdoor remote sensor temperature:
After the outdoor remote sensor is paired, on the indoor remote sensor press
the light button and WAIT 30 seconds.
The antenna icon will flash 3 times, and the outdoor temperature will appear
at the top of the LCD screen.
To check the connection of the outdoor remote sensor to the equipment module at the installation site, press the button on the outdoor sensor and wait 15 seconds. The LED will blink white while the outdoor sensor is checking the connection and then show the following status indicators: BLUE – Good Connection – YELLOW – Weak Connection – RED – No Connection / out of range.
Technician Setup
These steps must be done from the MAIN Thermostat in your PROsync System. This thermostat has a technician setup menu for easy installer configuration. To set up the thermostat for your particular application:
- Press the MENU button.
- Press and hold the technician setup button for 3 seconds. This 3 second delay is designed so that homeowners do not accidentally access the installer settings.
- Configure the installer options as desired using the table below. Use the keys to change settings and the next step or previous step key to move from one step to another. Note: Only press the DONE key when you want to exit the technician setup options.
- Press the DONE key to exit.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
The device shall be used in such a manner that the potential for human contact normal operation is minimized. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>