Annaijia CT5-62 Car Mounted Magnetic Suction Wireless Charging Bracket User Guide
- June 1, 2024
- Annaijia
Table of Contents
Annaijia CT5-62 Car Mounted Magnetic Suction Wireless Charging Bracket
USER MANUAL
Car mounted magnetic suction wireless charging bracket
Product Specification
Product Name：Car mounted magnetic suction wireless charging bracket
Product Model：CT5-62
Product Size: 66x 66 x 100mm
Product Material：TPU/Aluminum Alloy/PC+ABS
Product Weight: 92.7g
Input: 5V/3A; 9V/3A
Output: 15W/10W/7.5W/5W
Magnetic Pull: 15N (without protection case) / 18N (with metal ring plate)
Compatible for dashboard, car monitor
Accessories: 1pc x Metal Ring, 1pc x Protective film,
1set x Wet and Dry-Cleaning Wipes,1pc x Positioning Tool,
1pc x 1m USB-A to Type-C cable
Package Content
How to Install
1. Place the Cradle Knob on the Ball Joint
2. Connect the Mount Cradle with the Ball Joint
3.Insert the Mount Hook into the A/C Blade.
How to install the Air Vent Mount
How to Use
For iPhone 15/14/13/12 series with MagSafe
1. Connect the USB plug to car charger port and Type-C plug to your holder.
2. Connect the mobile phone with the wireless charger to charge.
Note that you can know the charging status by the battery display on the phone screen.
Charging Status Display:
P.S. Please kindly note the branding light is not indicator light.
For Use With Non-MagSafe Phones:
1. Clean the back of your phone or case with the provided wet and dry wipes. Then determine the center with the positioning tool.
2. Clean the back of your phone or case with the provided wet and dry wipes. Then determine the center with the positioning tool.
3. Stick the protective film on the center before installing the metal ring.
Attach the metal ring to the center, on top of the protective film.
NECESSARY : Stick the protective film on the center before installing the metal ring.
4. Attach the metal ring to the center, on top of the protective film.
Product Specifications:
- Product Name: Car mounted magnetic suction wireless charging bracket
- Product Model: CT5-62
- Product Size: 66 x 66 x 100mm
- Product Material: TPU/Aluminum Alloy/PC+ABS
- Product Weight: 92.7g
- Input: 5V/3A; 9V/3A
- Output: 15W/10W/7.5W/5W
- Magnetic Pull: 15N (without protection case) / 18N (with metal ring plate)
- Compatible for dashboard, car monitor
- Accessories: Metal Ring, Protective film, Wet and Dry-Cleaning
Wipes, Positioning Tool, 1m USB-A to Type-C cable
Attention:
1. Use with the phone case will affect the magnetic attraction, you can stick the metal ring plate to the phone cases.
2. The Metal Ring needs to sit for 12-24 hours before use.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This symbol indicates that this product shall not be treated as household waste.Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Frequently Asked Questions (FAQ):
Q: Can I use this product with non-MagSafe phones?
A: Yes, you can use this product with non-MagSafe phones by following the provided instructions for installation and usage.
Q: How do I clean the product?
A: You can clean the product using the provided Wet and Dry-cleaning wipes included in the accessories.
Q: What should I do if the magnetic attraction is affected when using a
phone case?
A: If the magnetic attraction is affected when using a phone case, you can stick the metal ring plate to the phone case to enhance the magnetic connection.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>