SMART CAREGIVER CORPORATION 433-EC with FMT-07C 24×48 Inch Gray CordLess Floor Mat Instructions
- June 1, 2024
- SMART CAREGIVER CORPORATION
Table of Contents
SMART CAREGIVER CORPORATION 433-EC with FMT-07C 24×48 Inch Gray Cordless
Floor Mat
Product Information
Specifications
- Product Name: Caregiver Alert Monitor with CordLess Sensor Pads/Mats
- Model: 433-EC
- Maximum Range: Up to 300 feet
Product Usage Instructions
Entering Programming Mode
- Use a paperclip or pointed tool to press and hold the Program button on the back of the monitor.
- When the outer two LED lights on the front of the monitor are solid, release pressure on the button.
- The lights will stay on to indicate that the monitor is in programming mode.
Programming Desired Components
- Ensure the transmitter is connected to a sensor pad and turned on.
- Place pressure on the sensor pad/mat and then release.
- If programming multiple components, repeat the process until all components are programmed.
Exiting Programming Mode
- Once programming is complete, press and release the program button on the back of the monitor.
- The outer two LED lights will blink to confirm programming and then turn off.
Transmitter Instructions (TM-12)
- Open the neck of the pad and pull out the transmitter.
- Turn on the transmitter by moving the switch to the on position.
- Check for the red light to turn on and stay lit briefly on the transmitter.
- The red light should blink every 45 seconds to indicate power.
- Place the transmitter back inside the pad’s neck and seal it closed with the provided sticker.
Please activate your pad following the provided steps before first use. Pads are shipped in Sleep Mode to preserve battery life.
FAQ
Q: What should I do if I encounter a low battery alert?
A: When you receive a low battery alert, please replace the batteries promptly to ensure continuous monitoring functionality.
Q: How do I program a replacement pad/mat to 433-EC?
A: Follow the programming instructions outlined in the user manual. Ensure the transmitter is turned on and connected for successful programming.
Quick Start Instructions
- ENTER PROGRAMMING MODE: Use a paperclip or a pointed tool to press and hold the “Program” button within the hole on the back of the monitor, located under “Program”. When the outer two LED Lights on the front of the monitor are solid, release pressure on the button. The lights will remain on to indicate that the monitor is in programming mode.
- REPLACING OR ADDING TO 433-CMU-40/60?
- Scan for 433-CMU programming instructions
- PROGRAM DESIRED COMPONENTS:
- Have components ready before starting
- Cordless Sensor Pads/Mats: The transmitter must already be connected to a sensor pad and turned on.
- Place pressure on the sensor pad/mat and then release.
- Maximum Range: Up to 300 feet.
- If programming multiple components, repeat step 1 until all components have been programmed & continue to step 3 to exit programming.
- EXIT PROGRAMMING MODE: Once the programming is complete, press and release the program button on the back of the monitor.
- The outer two LED lights will blink to confirm programming and turn off.
- Call Customer Service at 800-650-3637 for assistance.
Replacement Pads/Mats
Please make sure the transmitter inside the neck of your sensor pad/mat is turned on before trying to program the monitor
- Open the neck of the pad and pull out the transmitter.
- Turn on the transmitter by moving the switch to the on position.
- Once you have the switch in the on position, you should see the red light turn on and stay lit for a short time on the top side of the transmitter.
- Once the red light turns off, it should blink every 45 seconds to show that it has power.
- Now that you have the transmitter turned on, you can place it back inside the neck of the pad and seal closed with a provided sticker. Please activate your pad by following the steps below.
Once Transmitter is turned on, it is intended to stay on for the life of the pad. DO NOT use it as an ON/OFF switch.
Press and hold for 30 seconds
- Pads must be activated before first use.
- Pads are shipped in “Sleep Mode” to preserve battery life.
To activate:
- Press and hold the pad for 30 seconds then release.
- This pad is now activated and “ON”. This is only necessary for the first time use.
- See monitor instructions for programming
- FCCID: 2AUNUTM-12
FCC Notice
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, according to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used under
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced RF technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>