Aukivon Blanket Portable Infrared Sauna User Guide
- June 1, 2024
- Aukivon
Table of Contents
Aukivon Blanket Portable Infrared Sauna
PRINCIPLE AND EFFECT
THE SWEAT STEAMING BLANKET GENERATES HEAT AND ACHIEVES THE EFFECTS OF REMOVING COLD, DAMPNESS, AND ACID BY PERSPIRATION WITH INFRARED RAYS.
PRODUCT HOST PANEL, PORTS AND ACCESSORIES.
PANEL DIAGRAM
PORT DIAGRAM (BACK)
NOTE: TERMINALS 1, 2 ARE IN CORRESPONDENCE WITH PANEL OUTPUT1-2.
- WORK TIME DISPLAY
- PORT 1 TEMPERATURE DISPLAY
- PORT 2 TEMPERATURE DISPLAY
- PORT 2 STATUS DISPLAY
- PORT 1 STATUS DISPLAY
- START/PAUSE
- TIME+ / TEMPERATURE +
- TIME- / TEMPERATURE –
- TIME / TEMPERATURE ADJUSTMENT AND SWITCH
ACCESSORY DIAGRAM
THE PLUG OF EACH SIDE IS IN CORRESPONDENCE WITH THE SIDE HEATING
OPERATION STEPS
STEP1: LAY THE SWEAT STEAMING BLANKET FLAT, AND KEEP THE TWO CONNECTION
LINES OF THE SWEAT STEAMING BLANKET CONNECTED TO THE PORT OF THE HOST.
STEP 2: ADJUST THE TIME AND TEMPERATURE, LIE FLAT IN THE STEAMING
BLANKET, AND PULL THE ZIPPER ON THE UPPER AND LOWER BLANKET.
STEP 3: CONNECT THE POWER AND TURN ON THE POWER SWITCH (THE DEFAULT
DISPLAY TIME OF THE INSTRUMENT IS 30 MINUTES, AND THE TEMPERATURE DISPLAYED IS
60°C).
STEP 4: BUTTON (7, 8), SET THE WORKING TIME (1-60 MINUTES,OPTIONAL)
STEP 5: BUTTON (9), DIGITAL TUBE (2) FLASHES, SET PORT(1)OUTPUT
TEMPERATURE (30-80°C, OPTIONAL) WITH BUTTON ( 7. 8), INPUT VALUE IS
AUTOMATICALLY SAVED BY THE INSTRUMENT.
STEP 6: PRESS THE BUTTON (9) AGAIN, THE DIGITAL TUBE (3) FLASHES, USE THE
BUTTONS (7, 8) TO SET THE PORT(2) OUTPUT TEMPERATURE (30-80C, OPTIONAL), ENTER
THE NUMBER WHICH WILL BE AUTOMATICALLY SAVED BY THE INSTRUMENT.
STEP 7: PRESS (9) AGAIN, AND THE DIGITAL TUBE (1) FLASHES, THE INSTRUMENT
STATE WILL RETURN TO THAT OF THE WORKING TIME, AND THE STEPS OF 5 AND 6 CAN BE
OPERATED ON REPEAT.
bAFTER SETTING THE WORKING TIME AND OUTPUT TEMPERATURE, PRESS THE BUTTON (6)
TO START THE INSTRUMENT (THE DIGITAL DISPLAY STOPS FLASHING WHEN NOT IN USE),
A SMALL FLASHING DOT IN THE LOWER RIGHT CORNER OF THE DIGITAL TUBE 1 APPEARS.
①IF THE INSTRUMENT IS NOT PLUGGED IN ACCESSORIES, AFTER PRESSING (6), THE
TEMPERATURE DISPLAYS “ONE”. BUT IF ALL THE OUTPUT PORTS HAVE BEEN ACTIVATED,
CONNECT THE ACCESSORIES AND PRESS THE DEFAULT OR SET TEMPERATURE TO
AUTOMATICALLY START HEATING;
②DIRECTLY PRESS THE BUTTON (6) WHEN YOU HAVE TURNED ON THE MACHINE ( CAN SET
THE TIME FIRST), ALL PORT OUTPUTS WILL BE STARTED AT THE DEFAULT 60℃;
③PUSH THE BUTTON (6) DURING OPERATION AND ALL THE TERMINAL OUTPUT WILL BE
PAUSED (IF YOU DON’T WANT TO USE A PORT OUTPUT, YOU CAN DIRECTLY UNPLUG THE
CORRESPONDING PIN)
STEP 9: AFTER START, THE TEMPERATURE DISPLAY VALUE IS THE CURRENT
TEMPERATURE OF THE ACCESSORIES.
ALSO, THE INDICATOR LIGHT BELOW THE TEMPERATURE DISPLAY IS ALWAYS ON; WHEN THE
SETTING TEMPERATURE IS REACHED,THE CORRESPONDING INDICATOR LIGHT WILL GO OUT
AND THE INSTRUMENT WILL STOP HEATING; WHEN THE
TEMPERATURE OF THE ACCESSORIES DROPS SLIGHTLY, THE INDICATOR LIGHT WILL LIGHT
UP AND HEAT UP AGAIN TO MAINTAIN TEMPERATURE CONSTANT STATE.(THE TEMPERATURE
WILL FLOW BETWEEN PLUS OR MINUS 2°C AT A CONSTANT TEMPERATURE)
STEP 10: AFTER USE, TURN IT OFF AND CUT OFF THE POWER; WHEN THE
TEMPERATURE DROPS TO A SUITABLE RANGE, OPEN THE ZIPPER OF THE SWEAT STEAMING
BLANKET, WHICH CAN HELP THE CUSTOMER TO GET UP FROM THE BLANKET SLOWLY.
HOST PARAMETERS
POWER SUPPLY VOLTAGE: AC110V 220V
WORKING FREQUENCY: 50HZO 60HZ
WORKING POWER: 650W
CARTON SIZE: 80X36X17CM
PRECAUTIONS
- WHEN THE INSTRUMENT IS IN WORKING CONDITION, IF YOU NEED TO ADJUST THE TEMPERATURE, YOU CAN DIRECTLY SET IT BY PRESSING THE CORRESPONDING TEMPERATURE SETTING KEY WITHOUT PAUSE OR SHUTDOWN TO AVOID AFFECTING THE SERVICE LIFE OF THE ACCESSORIES.
- WHEN USED, THE HEATING PARTS INSIDE THE ACCESSORIES CAN’T BE CLOSE TO EACH OTHER OR STACKED TOGETHER; AFTER USE, PLEASE REMOVE THE ACCESSORIES AND PLACE THE UPPER AND LOWER BLANKETS SEPARATELY. AFTER THE RESIDUAL HEAT IS EXHAUSTED, THEY CAN BE CLEANED AND DISINFECTED. AFTER DRYING, THEY SHALL BE FOLDED AND PLACED IN A DRY AND VENTILATED PLACE.
- THE TEMPERATURE ABOVE 75 DEGREES IS HIGH TEMPERATURE, PLEASE USE IT CAREFULLY.
- IT IS NOT SUITABLE FOR PREGNANT WOMEN, UNHEALED WOUNDS, PATIENTS WITH SEVERE HYPERTENSION, WOMEN DURING MENSTRUAL PERIOD, AND AFTER DRINKING! THE ELDERLY AND CHILDREN SHOULD BE USED UNDER THE SUPERVISION OF ADULTS.
NOTE: BEFORE USE, SPREAD THE TWO BLANKETS AND HEAT THEM TO PREVENT STICKINESS. AFTER USE, IT SHALL TO BE COMPLETELY COOLED BEFORE BEING FOLDED AND STORED!!!
ACCESSORY LIST
THE HOST: 1| POWER LINE: 1| TWO-STAGE SWEAT BLANKET: 1| SET
MANUAL: 1
---|---|---|---
- PLEASE REFER TO THE ACTUAL PRODUCT; IF YOU HAVE SPECIAL NEEDS, PLEASE DIRECTLY CONTACT THE DEALER.
- PLEASE DO NOT CONNECT THE ACCESSORIES NOT MATCHED WITH THIS MACHINE TO AVOID INJURY.
TROUBLESHOOTING METHODS
| FAULT CONDITIONS | TROUBLESHOOTING METHODS |
|---|---|
| TURN ON THE HOST, THE HOST DOES NOT RESPOND | CHECK WHETHER THE POWER SUPPLY IS |
PROPERLY CONNECTED.
CHECK WHETHER THE POWER SWITCH IS TURNED ON.
NO OUTPUT.| CHECK WHETHER THE ACCESSORIES ARE PROPERLY CONNECTED TO THE HOST
OVERLY LONG USE, SHUT DOWN AND COOL NATURALLY.
CHECK WHETHER THE POWER SUPPLY VOLTAGE IS NORMAL. (PROFESSIONALS ARE REQUIRED)
THE COMPLETE MACHINE IS NOT POWERED ON| CHECK WHETHER THE FUSE IS BURNED OUT.
IF IT IS BURNED OUT, PLEASE REPLACE THE DEVICE.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>