HALO HOME HIWAC1BLE40A In Wall Accessory Dimmer Instruction Manual

June 1, 2024
HALO Home

HALO HOME HIWAC1BLE40A In Wall Accessory Dimmer

Wall Accessory Dimmer

INSTRUCTION MANUAL

ONLY USE WITH NON-SMART LIGHTS

WARNING

  • Turn OFF circuit breaker or remove fuse(s) and test that power is off before wiring or servicing.
  • Never wire any electrical device with power turned on. Wiring device with power on may cause permanent damage to product and void warranty.
  • If you are not sure about any part of these instructions, please contact a licensed electrician.
  • Minimum 75°C supply conductors

CAUTION

  • Edges may be Sharp – Wear gloves while handling.
  • Connect dimmer to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
  • Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.

PACKAGING CONTENTS

A. Accessory Dimmer B. (4) Wire Nuts C. (2) Screws

Wall Accessory Dimmer

ITEMS REQUIRED (Purchase separately)

  • Philips Screwdriver
  • Labels or electrical tape for tagging wiring
  • Voltage tester
  • Tape or labels (3- or 4-way wiring)
  • Gloves

SINGLE LOCATION OVERVIEW

The HALO Home Accessory dimmer easily replaces a single location standard switch/dimmer once the connected lighting has been retrofitted with HALO Home Smart Lighting or is connected to a HALO Home Smart Device.
This Dimmer will only control HALO Home Smart Lights and Devices wirelessly – it does not control non-smart loads.*

The Accessory Dimmer sends wireless signals to the HALO Home Smart Light(s)/Device(s) it’s commissioned to control and the lighting/controlled load turns ON/OFF.

MULTI-LOCATION CONTROL OVERVIEW

Multiple Accessory Dimmers can control the same smart lights/devices for easy 3- or 4-way control.

MAX Load: 300W HALO Home Smart LED Lighting

*For control of non-smart loads, use the HALO Home Smart Dimmer or HALO Home Smart Switch.

Wall Accessory Dimmer

TIPS: When retrofitting existing dimmer locations:

  • Verify that there is a neutral wire available at EACH dimmer location.(White wires connected to dimmer terminals and marked with electrical tape are typically NOT neutral wires.)

  • HALO Home Accessory Dimmers cannot wire downline of a Smart Switch, Smart Dimmer, or other dimming/switching device.
    They require a constant hot feed  (unswitched and undimmed).

  • Because it does not directly control the Smart Light/Device, the HALO Home Accessory Dimmer does not need to be powered from the same circuit and can be connected for power to any convenient constant power circuit (undimmed and unswitched).

3-way and 4-way wiring can be confusing. If wiring does not match diagrams shown, stop and consult with an electrician.

SINGLE-POLE INSTALLATION (1 Dimmer)

1. Turn OFF power at the circuit breaker and remove the wall plate

2. Leaving wiring attached, pull the dimmer away from the wall.

3. Verify that there is a neutral wire available. If not, stop and consult a licensed electrician.

4. Turn the wall dimmer to the OFF position but leave the wires connected.

5. Ensure wiring is safely separated and terminals are not touching anything, and then turn ON power at the circuit breaker.

6. DO NOT TOUCH EXPOSED WIRE OR TERMINALS. Using a voltage tester, determine and note which wire still has power (‘Hot’).

7. Turn OFF power at the circuit breaker

8. Use a label or electrical tape to tag the identified ‘Hot’/power wire.

9. Disconnect the wires and remove the dimmer.

10. Connect the HALO Home Accessory Dimmer (A) using provided wire nuts (B).

i. Connect the tagged ‘Hot’ wire to the Accessory Dimmer’s black wire.
ii. Connect the bare copper or green ground wire from the wall-box to the Accessory Dimmer’s green wire.
iii. Connect the other dimmer wire (load) to the Accessory Dimmer’s red wire.
iv. Connect the neutral wire in the wall-box to the Accessory Dimmer’s white wire. (NEUTRAL IS REQUIRED).

Wall Accessory Dimmer

11. Using the screws provided (C), mount the Accessory Dimmer in the wall-box and attach a wall plate (not included).

12. Turn ON power at the circuit breaker. (An LED indicator will start flashing when power is turned ON).

Wall Accessory Dimmer

13. Using your smart phone/tablet, follow the online Quick Start Guide to pair this product to your HALO Home account. support.BringHaloHome.com

3-WAY INSTALLATION (2 Dimmers)

1. Turn OFF the light using one of the dimmers. Turn OFF power at the circuit breaker.

Wall Accessory Dimmer

2. Remove the wall plates from the existing light dimmers.

3. Leaving wiring attached, remove screws and pull the dimmers away from the wall. Verify that BOTH dimmer locations have a neutral wire available. If not, stop and consult a licensed electrician.

Wall Accessory Dimmer

4. At each dimmer location, place electrical tape or a label on the wire connected to the different colored screw terminal (common).

5. Ensure wiring is safely separated and terminals are not touching anything, and then turn ON power at the circuit breaker.

Wall Accessory Dimmer

6. DO NOT TOUCH EXPOSED WIRE OR TERMINALS. Using a voltage tester, determine which dimmer location has power on the tagged wire. (The powered location is connected to the breaker while the unpowered location is connected to the lighting load.)

Wall Accessory Dimmer

7. Use a tape or label to tag the powered dimmer location “POWER”. Label the other dimmer location “LOAD”.

Wall Accessory Dimmer

8. Turn OFF power at the circuit breaker.

9. Disconnect the wiring and remove both dimmers.

Wall Accessory Dimmer  Wall Accessory
Dimmer

10. At the location labeled “POWER”, connect the HALO Home Accessory Dimmer (A) using provided wire nuts (B).

i. Connect the tagged wire (Power) to the Accessory Dimmer’s black wire.
ii. Connect the bare copper or green ground wire from the wall-box to the Accessory Dimmer’s green wire.
iii. Connect the other 2 dimmer wires to the Accessory Dimmer’s red wire.
iv. Connect the neutral wire in the wall-box to the Accessory Dimmer’s white wire. (NEUTRAL IS REQUIRED).

Wall Accessory Dimmer

11. At the location labeled “LOAD” connect the HALO Home Accessory Dimmer using provided wire nuts.

v. Connect the tagged wire (lighting load) to the Accessory Dimmer’s red wire.
vi. Connect the bare copper or green ground wire from the wall-box to the Accessory Dimmer’s green wire.
vii. Connect the other 2 dimmer wires (incoming power) to the Accessory Dimmer’s black wire.
viii. Connect the neutral wire in
the wall-box to the Accessory Dimmer’s white wire. (NEUTRAL IS REQUIRED).

Wall Accessory Dimmer

12. Using the screws provided (C), mount the Accessory Dimmer in the wall-box and attach a wall plate (not included).

13. Turn ON power at the circuit breaker. (An LED indicator will start flashing when power is turned ON).

Wall Accessory Dimmer

14. Using your smart phone/tablet, follow the online Quick Start Guide to pair this product to your HALO Home account.support.BringHaloHome.com

3-WAY WIRING DIAGRAM

Wall Accessory Dimmer

4-WAY INSTALLATION (3+ Dimmers)

In locations with 3 or more dimmers, the following rules will be true:

  • 2 locations will have 3-way dimmers: 3 wiring terminals plus a ground terminal.
  • All remaining locations will have 4-way dimmers: 4 wiring terminals plus a ground terminal.

1. Follow steps 1 – 3 in the “3-WAY INSTALLATION (2 Dimmers)” section, removing 3- and 4-way dimmers from the wall in step 3. All dimmer locations must have a neutral.

2. At the two 3-way dimmer locations, follow steps 4 – 11 in the “3-WAY INSTALLATION (2 Dimmers)” section and then return to this section for further instruction.

3. Make sure circuit breaker is still OFF from previous steps.) At each 4-way dimmer location, identify the 2 separate pairs of wires

Wall Accessory Dimmer

4. Disconnect the wiring, keeping the 2 pairs separated.

Wall Accessory Dimmer

5. Connect HALO Home Accessory Dimmers at each 4-way dimmer location using provided wire nuts.

i. Connect 1 pair of wires to the Accessory Dimmer’s black wire.
ii. Connect the bare copper or green ground wire from the wall-box to the Accessory Dimmer’s green wire.
iii. Connect the other pair of wires to the Accessory Dimmer’s red wire.
iv. Connect the neutral wire in the wall-box to the Accessory Dimmer’s white wire. (NEUTRAL IS REQUIRED).

Wall Accessory Dimmer

6. Using the screws provided (C), mount all dimmers in the wall-boxes and attach wall plates (not included).

7. Turn ON power at the circuit breaker. (An LED indicator will start flashing on all dimmers when power is turned ON).

8. Using your smart phone/tablet, follow the online Quick Start Guide to pair this product to your HALO Home account.support.BringHaloHome.com

4-WAY WIRING DIAGRAM

Wall Accessory Dimmer

FACTORY RESET

ONLY DO THIS STEP IF YOU ARE UNABLE TO REMOVE THE DEVICE USING THE APP.

If removal does not work, delete it in the app by clicking “my device is broken” and then follow the factory reset steps:

1. Press and hold the ON button for 12 seconds to reset.
2. The load may turn OFF or ON and the LED will start flashing indicating the reset is processing. The LED will continue flashing to indicate that the dimmer is ready to be paired with the HALO Home App.

CIRCUIT DISCONNECT (AIR-GAP)

Disconnect power to this dimmer and any connected loads by using a flathead screwdriver to pull the air-gap dimmer out until you hear a click.

Specifications:

  • Model: HIWAC1BLE40A
  • Usage: In-Wall Accessory Dimmer
  • Compatibility: Only for use with non-smart lights
  • Max Load: 300W HALO Home Smart LED Lighting

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: 2AKCY-HIWAC1BLE40
Responsible Party – U.S. Contact Information
Cooper Lighting Solutions
1121 Highway 74 S
Peachtree City, GA 30269
www.cooperlighting.com

IC Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

5-YEAR WARRANTY

For warranty information, please visit
www.cooperlighting.com/legal

SUPPLEMENTAL INFORMATION

Construction of control: Independently Mounted for Flush Mounting
Type of Action: Type 1.B Action
Pollution Degree: 2
Rated Impulse Voltage: 2500 V
Software Class: Class A

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com

© 2021 Cooper Lighting Solutions
All Rights Reserved.

Specifications and dimensions subject to change without notice.

FAQ (Frequently Asked Questions)

Q: What should I do if my wiring does not match the diagrams?

A: Stop and consult with an electrician to ensure correct installation.

Q: Can the Accessory Dimmer control non-smart loads?

A: No, for non-smart loads, use HALO Home Smart Dimmer or HALO Home Smart Switch.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals