Electronic Silk Road Shenzhen Tech Co Ltd 2C562A HaloLock Mini Wireless Charger User Guide

Electronic Silk Road Shenzhen Tech Co Ltd 2C562A HaloLock Mini Wireless

Charger

Thanks for choosing ESR!
To mere you get he most out of your new charger, read this manual before use. When you’re done, keep it.

Using Your Charger

1. This is a magnetic wireless charger that automatically aligns with the wireless charging coil in your iPhone (requires an iPhone with MagSafe or magnetic phone case).
2. Plug the USB-C cable into a power adapter and magnetically attach the charger to begin charging.

Important Reminders

1. The charger only supports magnetic attachment with a caseless iPhone with MagSafe, an official MagSafe case, an ESR HaloLock™ case, or a standard case with a HaloLock™ Universal Ring. It may not attach to other magnetic cases. It will not attach to any other non-magnetic phones or cases. (Over time, the charger may leave a faint circular mark on the back of your phone that can be easily cleaned with an alcohol wipe.)
2. This charger supports an input of 9V2.22A and outputs a maximum of 15W.
3. For maximum charging speed, use a charging adapter compatible with QC (Quick Charge) 2.0/3.0 or PD (Power Delivery) fast charging.
4. The charger must be connected to a power source to begin wireless charging.

Safety Warnings

1. Do not expose the device to temperatures below 0°C (32°F) or above 60°C (140°F).
2. Do not expose the device to an open flame or submerge it in water as this will damage the device.
3. Always check for damage to the device, cables, or other accessories before using the device. If damaged, do not use the device.
4. Do not attempt to disassemble or modify the device in any way, as it may cause serious damage and void the warranty
5. Do not expose the device to corrosive liquids, or high humidity as they will seriously damage the device and void the warranty.

FCC ID:2APEW-2C562A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
• These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC:24790-2C562A
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.”

• This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with a minimum distance of 10 centimeters between the radiator and your body.

Declaration of Conformity

This product is intended for use within Europe. Electronic Silk Road Corp, hereby declares that this product 20562 is in compliance with the Essensa requirements and other relevant provisions of Directive 4014/23/20.2014/35/20.2014/30760. The Declarator of Conformity. for the 2C562 is available from www.esrgear.com

Scan to watch a quick setup video

Documents / Resources

| Electronic Silk Road Shenzhen Tech Co Ltd 2C562A HaloLock Mini Wireless Charger [pdf] User Guide
2C562A HaloLock Mini Wireless Charger, 2C562A, HaloLock Mini Wireless Charger, Mini Wireless Charger, Wireless Charger, Charger
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>