DEMEX GROUT TK3 Cordless Tool Kit User Manual
- June 1, 2024
- DEMEX GROUT
Table of Contents
DEMEX GROUT TK3 Cordless Tool Kit
Specifications
- Charger Input: 100-240V, 50/60Hz
- Battery Pack: 18V, 4Ah
- Propulsion Force: 500N
- Net Weight: 5.2 lbs (2.35 KG) with battery
Safety Instructions
Battery Pack
- Do not charge a damaged battery pack.
- Do not try to disassemble the battery pack. When maintenance or repair is required, it should be handed over to professional maintenance personnel. Incorrect assembly may create product failure or personal injury.
- Do not drop, vibrate or hit the battery pack.
- The battery pack must be kept away from high temperature or flame. Do not place the battery pack on fire or heater, nor expose it to strong sunlight for a long time.
- Do not expose the battery pack to water or rain.
- The storage ambient temperature range of the battery pack is 30-110℉(0-45℃).
Charger
- Use the original charger for charging.
- The charger can not be placed in water or a humid place.
Important:
Under no circumstances will compliance with the information in this manual
relieve the user of his/her responsibility to comply with all applicable codes
or safety standards.
Specification
| Charger | Input: 100-240V, 50/60Hz |
|---|---|
| Battery Pack | 18V, 4Ah |
| Speed Set | 1 |
| Propulsion Force (unit:N) | 500 |
| Net Weight | 5.2 lbs (2.35 KG) with battery |
Parts and Functions
1. Piston
| Thrust the bottom of the grout cartridge and squeeze the grout material out.
---|---
2. Cartridge holder| Contain and lock the cartridge.
3. Rod handle| N/A
4. Clutch plate| Press to pull or push the rod.
5. Trigger
| Press and hold to forward the rod. Loose it and the rod will retreat a bit to stop squeezing the grout out of the cartridge.
| Power On/Off| Hold the button to power on/off the device.
Speed set
| Press the button to change the speed. Five feed speed shifts to select.
Default speed set is at 5.
7. Battery pack| N/A
Operation
- a. P ress the clutch plate and pull backward the rod.
- b. Insert the cartridge. Make sure the neck of the cartridge is fixed on the rail of the holder.
- c. Install the battery pack.
- d. Power on the device and set the propulsion speed. For new users, it is advised to start from speed shift 1. After you are used to the feed speed and operation, then turn up the shift.
Troubleshooting
| Problem | Cause | Solution |
|---|---|---|
| During feeding, the rod is stuck and can not be pulled back. | The speed shift |
set is too high. Two factors may cause this stuck. When the nozzle outlet is small, the high propulsion speed would lead high pressure inside the cartridge. In such case, the software stops the feeding to prevent the possible cartridge crack due to high pressure from inside. Low flowability because of cold
weather may also cause this stuck.
| Re-power on the device. Press the trigger to retreat the rod. Turn down the speed shit. Then continue
the operation.
The cartridge is burst during
feeding.
| The cartridge body is cracked or scratched before operation. Or the nozzle outlet is not
good to flow out.
| Find the cause and settle.
Product Disposal
Commercially reasonable efforts were made to ensure that the specifications and other instructions in this manual are accurate and complete at the time of its publication. The information in this manual is subject to change at any time without prior notice. Dispose of the battery pack according to the local, state and federal regulations.
Warranty
This device has a year warranty from the date of purchase.
Demexgrout LLC
- ADDRESS: 1942 Broadway St, Ste 314C Boulder, CO 80302
- Tel:201-367-8945
- info@demexgrout.com
FAQ
Q: How to dispose of the product?
A: Dispose of the battery pack according to local, state, and federal regulations.
Q: What is the warranty period for this product?
A: This device has a one-year warranty from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>