Unication G-Series Charger Amplifier Instruction Manual
- June 1, 2024
- Unication
Table of Contents
Unication G-Series Charger Amplifier Instruction Manual
Charger Amplifier
For Unication G-Series P25 Voice Pagers
Rugged. Reliable. Built to LAST.
Email: Info@Unication.com
Website: www.Unication.com
Note: Please read the following sections before using the Charger Amplifier
for G-Series Voice Pagers.
IMPORTANT SAFETY INFORMATION
To ensure the safe use of thisproduct:
- Use your charger amplifier only with the supplied power adaptor.
- Use the batteries provided by Unication for your G-Series product.
- Keep your charger amplifier away from high temperature, high humidity, dust, chemicals and corrosive materials.
- Do not disassemble your charger amplifier or power adaptor.
- This device complies with part 15 of the FCC Rules.
- Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
OVERVIEW
A-1 Standard Package:
Standard package contains:
A-2 Specification:
B-1Front View:
B-2 Top View:
B-3 LED Indicators:
B-4 Rear View:
-
Power Source:
Connect the Charger Amplifier to power outlet (110/60 Hz) with the supplied Adaptor. -
Charging G-Series Pager:
Insert the G-Series Voice Pager into Charger Amplifier’s Pager Socket tightly. The charging process starts with the Charging LED indicator turning orange. When the battery is fully charged, the LED turns green. -
Charging USB Device:
Connect the USB device to the Charger Amplifier’s USB Charging Port with USB Cable. -
Voice Message Amplification:
Turn on G-Series Voice Pager and insert into the Charger Amplifier’s pager socket.
When the pager receives voice messages, it will be amplified based on the volume knob setting.
5 External Antenna Port:
Unication provides the antenna below with the G2-G5 Charger Amplifier:
Multi-Band (VHF, UHF, 700-800 MHz)
9 Alarm Device 6 Pin Din Port:
*This Connection provides line level audio not controlled by the volume knob. Using this connection will not mute the onboard speaker.
Relay Dry Contact Closure Specs:
(Pins 2 and 3) When the accessory relay is energized, its contacts close and
present a short across pins 2 and 3 of the connector. The relay contacts are
rated for 10 watts maximum at 28VDC/ACRMS. Within the limits of the 10-watt
rating the closed contacts can handle up to 750mA continuously and switch up
to 400mA of current.
Relay Control:
Relay Control is set up from inside the G-Series Voice Pager PPS (Pager
Programming Software). Navigate to the “Group ID Setting” tab of PPS and in
the Group ID list, select the option for “Relay Control” to enable and program
Amp Charger relay control.
10 USB Charging Port :
This port is for charging USB device and Bluetooth earpiece(5V/300mA).
11 Power Input:
The Charger Amplifier for G-Series Pagers uses a 12V/1.5A DC ADAPTOR, power input is 100~240VAC with maximum power 18W. Please connect to the power outlet with supplied power adaptor.
12 External Equipment Control:
The Charger Amplifier provides a variety of I/0 for external device control.
12-1. Horn Speaker (Loudspeaker)
Step 1. Insert a powered-on G-Series Pager into the Charger Amplifier.
Step 2. Select RCA connector and connect the external equipment.
Step 3. When any message is received, the relay closure is asserted and audio
is active.
Step 4. Audio can be terminated by either shutting the G-Series Voice Pager
off or depressing the Reset button on the pager.
12-2. Fire Alert Indicator
Step 1. Insert a powered-on G-Series Voice Pager into the Charger Amplifier.
Step 2. Using the DIN Connector, connect the external equipment to the
appropriate signaling pins.
• Pins 1 and 6 are outputs and are used to control a remote speaker.
• Pins 2 and 3 are normally open dry contacts and close when a page is
received.
• Pins 4 and 5 are not utilized on the G-Series Amplified Charger, all timing
of the dry contacts is controlled via the PPS (Pager Programing Software).
Step 3. Upon receiving a page, the relay and audio output are activated.
13 Amp Charger Connectors:
G-Series Charger Amp Terminal Connector Block
Part Number: 2811923-AMP
G-Series Charger Amp Din Connector
Part Number: CP-1050-ND
info@Unication.com
www.Unication.com
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>