lo bgo RH-338 Wearable Breast Pump User Manual
- June 1, 2024
- lo bgo
Table of Contents
lo bgo RH-338 Wearable Breast Pump
Congratulations on becoming a mother! If this is your first experience using a breast pump, it may take you some time to familiarise with its usage It is important for you to relax during the process even if you may not be able to squeeze out as much milk as you would like to at the start. Your body will adapt accordingly so that after several attempts, you will be able to extract more milk.
READ BEFORE USE
- Please limit each use to less than 15 minutes It is perfectly normal when not much milk is squeezed out within this period at first but with regular usage. your body will eventually adapt to produce more milk.
- Research have shown that to achieve optimum breast milk production, you should be in a totally relaxed state.It helps you release the hormone oxytocin that stimulates your let-down reflex for milk ejection. So, sit back on your favourite couch while listening to your favourite Songs, try deep breathing exercises or get your partner to give you a massage!
- The device comes with a massage feature that you may use (1- 3 mins) before pumping. This alows you to release the hormone oxytocin and increase milk production.
- Clean regularly. Clean any pump parts that have been in contact with your breast milk and wash your hands before and after use.
- Choose the appropriate optimum suction level. Gradually increase the breast pump suction until it becomes slightly uncomfortable, and then turn it down a notch. The pump will resume from the last used suction level when restarted.
- Since this is a wearable breast pump. please ensure that you use a proper breast shield.
PRODUCT DESCRIPTION
Accessories include
- Pump motor x2
- Milk collector x2
- Linker x2
- Type-C cable x2
- Silicone massage petal (24mm) x2
- Valve x4
- Sealing ring x4
- Silicone gas cup x4
- Bra adjustment buckle x2
- Silicone massage petal (27 mm) X2
CONTROL PANEL
Modes
-
Massage function: 9 levels
( Massage first to stimulate milk production.) -
Suction function: 9 levels
( Please choose the appropriate optimum level, the pumping mode is designed for slow suction, deep suction.) -
Stimulation function: 3 levels
(Massage and suction used simultaneously which is excellent for sunken nipples or first-time new users. turn on milk adopts 3+1 mode. 3 short-frequency massages and 1 deep suction.)- Turn on/off: Press and hold the power button for 3 seconds.
- Mode Change: Press the mode key .
- Level change: Press the and to increase or decrease level.
Battery Indicator and Milk Alarm
- Flash Red: Low battery (require charging.)
- Solid Green: Battery is fully charged (Flash green while charging.)
- Milk Warning: The alarm will flash red every 10 mins. It’s time to take out the milk collector, The pump will automatically turn off every 30 mins.
CLEANING INSTRUCTIONS
Before Use
- Remove the pump motor.
- Rinse in cold, clear water (approx+20°C/+68°F).
- Wash in warm water (approx+30°C / +86°F) using mild dish washing soap and wipe afterwards with a clean cloth.
- Rinse with cold, clear water (approx +20°C / +68°F) for 10 to 15 seconds.
- Boil in water for five minutes.
- Wipe down the parts with cloth or air dry before use.
After Use
- Rinse the milk collector, valve and linker immediately after use.
- Place all the silicone parts in boiling water for 3 to 5 minutes.
- Wipe down the parts with cloth or air dry before storage.
- Do not submerge pump motor in water.
ASSEMBLY
-
STEP 1
put the silicone gas cup into the linker, and press it with your hands to make the edges fasten tightly to ensure a perfect seal.
-
STEP 2
Install the valve into the bottom of the linker, make sure it is installed in the correct direction.
-
STEP 3
Put the assembled linker into the milk collector.
-
STEP 4
Place the silicone massage petal into the milk collector and ensure it is sealed properly to prevent leakages.
-
STEP 5
Install the pump motor.
DIRECTION FOR USE
MEASURED SIZE
Labigo comes with Breast Shields in two sizes, so you can find a Breast Shield
fit that is comfortable for you.
- To determine the correct size, put the Breast Shield on with the sizingmbol facing upwards and place your nipple in the center of the fit lines. The fit lines shouldwith the outside ofyour nipple.
- Try different Breast Shields to find the best fit for you.
- To comfortably pump on both sides, repeat this process for both niples to ensure you have the correct Breast Shield for each nipple.
ALIGN THE BREAST SHIELD TO THE DIRECTION OF YOUR NIPPLES WHEN YOU AREPUTTING IT ON:
- Bend forwards and hold your breast from underneath
- Bring the Breast Shield to your breast, paying attention to the direction our nipple
- You can use the markings on the Breast Shield to help align your nipple
In the bra placement
Press the silicone massage petal firmly against the breast, leave no gaps
and make sure your nipples are centered. Keep it upright. Be careful not to
move around the position of the product in your chest, otherwise the breast
pump wil not have suction.
Turn off and remove the pump carefully
Note: Do not lie down when using a breast pump. If you feel
uncomfortable while pumping or notice blisters or abrasions on your nipples or
breasts, try reducing the suction level of the breast pump.
SITTING POSITION FOR SUCTION
Relax the body, sit in a comfortable chair and lean slightly forward (use
cushion to support your back ).Make sure to keep the breast pump remains
upright.
POUR MLK
Please keep breast pump upright, and remove the pump motor from pump body
careful, to pour the milk into the botte, make sure the gap of milk collector
fit tightly against the bottle mouth.
INSTRUCTIONS FOR BRA ADJUSTING BUCKLE
Adjust the length of bra straps, make suction more comfortable. One end of the
bra adjustment buckle hung on the inside buckle of nursing bra. The length of
the bra straps can be adjusted by hooking the nursing bra buckle to the other
end of the bra adjuster buckle.
TROUBLESHOOTING
REMOTE CONTROLLER INSTRUCTIONS
Make sure the aspiration pump is properly placed in the care, and then press
And hold down the power button of the pump motor in 3 seconds to open it (or
short press the remote control “ “), Then point the remote control to the pump
motor, and then the switch mode is added or Reduce the inhalation level
according to the button on the remote control (as shown in the figure In the
picture). After use, press the remote control ( ) or press the pump motor The
power button is closed in 3 seconds to turn off the breast pump.
PRODUCT INFORMATION
FAQ
What should I do to ensure our breast pump with normal suction?
- Make sure that the breast pump is fully charged. (Approx. 2~3.5 hours, a full charge can be used for 2~2.5 hours. The motor cannot be turned on when charging.)
- Keep the main body of the breast pump and the accessories installed correctly and in a sealed state.
- Warm and massage your breasts before use to help suck millk.
- Center the nipples in the flanges. Lean forward slightly and turn the pump on.
- Keep the pump at a slow speed and low suction first. Then adjust the motor to the best suitable mode and level for yourself.
FCC STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>