SelectBlinds 2 Inch Sleek Cordless Faux Wood Blinds Installation Guide

2 Inch Sleek Cordless Faux Wood Blinds
Installation Guide

HOW TO INSTALL

2″ Cordless Lift Faux Wood Blinds with PVC Headrail

Finished looks

WITH VALANCE

WITHOUT VALANCE

Everything needed to install your blind

1. Installation brackets with mouting screws
2. Valance
3. Valance clips
4. Valance retum
5. L-bracket
6. Hold down through set screws (optional)
7. Its wand

Tools Needed

INSIDE MOUNT

1. Datennias brackel location
   Set install brackets info avakable open spaces on the headrad, awolding the crake and titer. Pace a plece of tape on the headrail at the canter of each bracket location. Mark the center of the tape with a pencil line. Remove brackats from headrall.

2. Mark location of blind
   Piece the headrail into the window opening and transfer the pencil mask. Remember to keep the headrest level even if your window is not. Remove tape after pencil marks have been transferred.
   WARNING
   Please acquire suitable anchor based upon wall construction

3. Instell mounting brackets
   Place bracket on canter tne. Make sure fhere is at least a ¼” gap behind ech bracket. Mark bracket holes.

4. Attach valance clips Install valance clips onto headrail by pushing the clips down over the headrail until you hear a clicking noise. One clip should be placed about 5½” from each end of the headrail. Addition clips, if any, should be evenly spaced between the first two clips. Clips must not interfere with blind ladders or other working parts.

5. Install headrail
   Hook headrail into brackets by rotating the headrail back into the Orachets unél lt stops. Push straight back until you hear a clicking noise.

6. Install valance Attach valance to the headrail by hooking valance clips into the valance. Push straight back unit valance snaps into clips.

7. Attach Wand Attach wand by pushing base of wand up info iter socket.

Optional: Install hold down brackets

OUTSIDE MOUNT

A. Determine bracket location

Set install brackets into available open spaces on the headrail avoiding the crade and iter. Place a piece of tape on the handrail at the center of each bracket location. Mark the center of the tape with a pencil line. Resnove brackets from the headrail.

B. Mark location of blind

Place headrail above window opening and transfer the pencil mark. Use a level to keep handrail level even if your window is not. Remove tape after pencil marks have been transferred.

WARNING
Please acquire suitable anchor based upon wall construction

C. Install mounting brackets

Place bracket on canter line. Mask bracket holes. Lise a level to keep brackets level when marking bracket holes.

D. Install headrail

Hook handrail into brackets by rotating the handrail back into the brackets until stops. Push straight back until you hear a clicking noise.

E. Assemble valance with returns

State L-bracket into groove on back side of valance and valance return, connecting the two pieces together.

F. Attach valance clips

Install valance clips onto valance by inserting clip into valance groove sideways and testing 90 degrees. One clip should be placed about 5½” from each end of the valance. Additional clips, if any, should be evenly spaced between the first two clips. Clips must not interfere with blind ladders or other working parts once attached.

G. Install valance

Attach valance to headrail by hanging valance cles on headrail, rotating the valance down, and snapping the chips into place.

H. Attach wand

Attach wand by pushing base of wand up into titer socket.

Optional: Install hold down brackets

How to operate

Push up or pull down on bottom rail to achieve blind height. Tum wand for light control.

Cleaning and care

Gaan with damp cloth and mild soap or lightly vacuum with a soft brush attachment.
A thin film of mad soap left on the stats helps keep static elactncity from budding up.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>