SelectBlinds B07PP1HQWD Classic Faux Wood Shutters Instruction Manual

**

**

SelectBlinds B07PP1HQWD Classic Faux Wood Shutters

Specifications :

• Frame: Top, Left, Right, Bottom
• Top Rail
• Stile
• Louver
• Tilt Rod
• Divider Rail (bigger shutter only)
• Bottom Rail

Product Usage Instructions

Before Installation:

• Inspect your package carefully. Contact 1-800-737-4569 for any questions.
• Tools Needed : Hand Drill, counter sink Drill Bit Set #8 (for shutters over 60″ tall and/or wide)

What’s in Your Package:

1. Shutter Panels with premounted hinges, pre-attached magnets
2. Mounting Hardware:
   • Medium screws for connecting shutter frames
   • Large screws for mounting the shutter frame to the wall opening
   • Pins for connecting hinges of the shutter panel to the frame
3. Shutter Frames with premounted hinges, corner joints, magnets

Assembly Instructions:

Step 1 of 3 :

1. Remove shutters from packaging, locate hardware bag.
2. Assemble Frame: Slip leg into top and bottom of frame. Use medium screws in pre-drilled holes.

Step 2 of 3:

1. Mount Pre-Drilled Frame:
   • For Outside Frame Mount or Inside Frame Mount, set frame in window opening using large screws.
   • Fill gaps with window caulking if needed.

Step 3 of 3 :

1. Reattach pre-hinged panels to the frame by matching up hinges and securing with pins.
2. Test shutter operation by opening and closing louvers using the tilt-rod.

Shutter Care :
Clean shutters with a damp cloth, feather duster, or wash with soap and water.

Frequently Asked Questions (FAQ):

1. Q: Can I install the shutters by myself?
   A: Yes, the installation process is designed to be easy and can be done by following the provided step-by-step instructions.

2. Q: What should I do if I encounter gaps during installation?
   A: You can fill any gaps between the frame, wall, an window sill with window caulking as an optional step.

Thank You For Your Purchase
Now that you have made the decision to beautify your space with timeless shutters, these step by step instructions will guide you through the easy installation process.

ANATOMY OF SHUTTERS

1. Frame (Top, Left, Right, Bottom )

2. Top Rail

3. Stile

4. Louver

5. Tilt Rod

6. Divider Rail
   (bigger shutter only)

7. Bottom Rail

What’s in your Package

1. Shutter Panels
   (with premounted hinges pre-attached and magnets)

2. Shutter Frames
   (with premounted hinges, corner joints & magnets)

BEFORE YOU BEGIN INSPECT YOUR PACKAGE CAREFULLY
Call 1-800-737-4569 for questions about your package.
Tools Needed

1. Hand Drill
2. For Shutters over 60” tall &/or wide counter sink Drill Bit Set #8
3. All Mounting Hardware included:
4. Medium screws – to connect shutter frames.
5. Large screws – to mount the shutter frame to the wall opening.
6. Pins – to connect the hinges together
7. the shutter panel to the frame.

ASSEMBLY INSTRUCTIONS 1 of 3

Mount Pre-Drilled Frame
Before Mounting, check which type of frame you will install to the wall.
NOTE: Fill any gaps between the frame, wall and/or window sill with window caulking (optional).

• OUTSIDE FRAME MOUNT
• INSIDE FRAME MOUNT

3. Mount Pre-Drilled Frame
Using the pre-drilled holes as your guide, set frame in window opening using the large screws. Set the top screws on both sides by drilling all the way in, then drill the screw back out & set back in. Do Not over tighten or distort frame. Set remaining screws after you rack the shutter.
Note: For panels taller or wider than 60”, drill an additional screw hole in the center of the existing holes, using a drill bit #8.

Use frame mounting screw top and bottom center.
Reattach the pre-hinged panels to the edge of the frame. Place the Pre-hinged panel in the frame by matching up the hinges. Now Drop in pins to secure each hinge.

• Now check your shutters by opening and closing the louvers by using the tilt-rod in the center of the panel to make sure they operate properly.
• Congratulations!
• Your new shutter installation is now complete.
• Thank You for your purchase.
• Shutter Care
  • Your shutters can be cleaned with a damp cloth, a feather duster or washed with soap and water.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>