IC ICLOVER TYD-YQC-001 Astronaut Galaxy Projector Star Light User Manual

IC ICLOVER TYD-YQC-001 Astronaut Galaxy Projector Star

Attention

• The light source of stars and nebulae is strong, so eyes should not look directly at the light source.
• The head and body of the astronaut are connected together by magnets, and the direction of the head can be adjusted. Do not stretch the astronaut’s head and body forcefully, otherwise the wires may break due to stretching.

Highlight Note：
The brightness of the stars (laser brightness) is greatly affected by the ambient temperature and use time, and the laser operating temperature is 10°-40C; When the ambient temperature is lower than 10°C, the laser cold start time is longer,and it is possible that the stars will not be seen when you first turn it on.
but the stars will gradually returns to normal after a few minutes of turning on;
When the ambient temperature is hot, the laser projector will inevitably dim after working for a long time (the laser itself will heat up when working).At this time,please turn the lights off and release its heat (usually it takes more than 15 minutes to dissipation heat).Then restart the star projector to restore normal brightness.

The direction of the projection can be adjusted by adjusting the rotation Angle of the astronaut’s head.

Please install the wheel before use, and confirm the wheel installation IN place (no gap between wheel and body)

Host Key Operation Instructions

Note: The product needs to be connected to a power cord for use.

• Power Switch: Press the power switch to turn on the machine. By default, the machine will turn on the nebula and stars at the same time.

• Nebula Switch: Short press the nebula button, you can switch the color of the nebula, every time you press to switch a color, so the cycle; Long press to turn off the nebula function, short press to turn on the nebula function again.

• Star Switch: Press the button to switch a star breathing rate every time.
  There are three modes of star breathing rate, namely “star breathing slow”, “star breathing fast” and “star steady on”. Long press the button to turn off the star function.

• Timing Indicator: After pressing any timing button of the remote control, the timing indicator lights up, and the indicator lights out after closing the timing.
  

Remote Control Instructions

• Switch: Short press the switch to turn on, and Nebula and Stars are turned on by default after turning on; short press the button again after turning on to turn off.
• Cancel Timing: Press this button to cancel timing.
• Nebula Brightness+: There are 5 levels of Nebula brightness. The default brightness is the middle level. Each time you press it, the brightness will increase by one level.
• Nebula Color Switch: Each time you press the button, the nebula will switch to one color. After a cycle, it will return to the default color. Long press the button to close the nebula. After closing the nebula, short press the button to reopen the nebula.
• Nebula Change Speed-: Nebula change speed is divided into five gears 0-1-2-3-4; gear 0 is static, gear 4 is the fastest changing speed, and the default gear is gear 2. Every time you press it, the speed of Nebula changes by one level until it reaches level 0.
• Nebula Change Speed+: The change speed of the nebula increases by one level each time you press it, until the third level.
• Nebula Brightness-: There are 5 levels of Nebula brightness. The default brightness is the middle level. Each time you press it, the brightness will decrease by one level.
• Star Mode 1: Star breathing rate slow mode.
• Star Mode 2: Star breathing rate fast mode.
• 45-Minute Timing : After pressing this button, the product will enter the 45-minute timer, and the timer indicator will turn blue.
• 90-Minute Timing : After pressing this button, the product will enter the 90-minute timer, and the timer indicator will turn red.
• Star Switch: The default brightness is the brightest. When the brig-htness is dimmed, press this button once to increase the brig-htness by one gear until the brightest gear.
  

CUSTOMER SUPPORT

Material:ABS/PC/PVC
Laser Wavelength:520nm
CLASSⅠLaser Products
Diode Laser-Max.Output<0.4mW
Rated Voltage:5V 1A
Control Mode:Remote control
Remote Control Range:<5meters(Best distance)
Product Size:109170185mm
Applicable Environment:Indoor Home(Better in a dark environment)
Working Temperature:10°~40°Celsius
Do not look directly at the laser light source!
This is not a toy, children should not use it
alone, please use it with an adult!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>