KAWDEN KWFV01 Smart Lock with Camera Instruction Manual

KAWDEN KWFV01 Smart Lock with Camera

KWFPOl
Wi-Fi Smart Lock
Installation Guide/ Quick Start Guide

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

1. Following the installation instruction to install the smart lock.
2. Download KK Home App.
3. Register and Log in KK Home App, add device by scanning QR code on the device.
4. Calibrate the smart lock and Complete Bluetooth & Wi-Fi settings in the App.

TOOL REQUIRED:
Do not use an electric screwdriver during installation.

IMPORTANT
Do not load batteries until lock is completely installed.

INSTALLATION OVERVIEW

Parts List

If any parts are missing or damaged, please contact Customer Support.

Prepare the door and check dimensions

• Measure to confirm that the hole in the door is 1-1/2″ or 2-1/8″ (38mm or 54mm)
• Measure to confirm that the hole in the door edge is 1″ (25mm).
• Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)
• Measure to confirm that the door is 1-3/8″ to 2″ (35 mm to 50mm) thick.
• Make sure the hole in the door frame is drilled a minimum of 1″ (25mm) deep, to leave enough space for the deadbolt to extend into the door frame when the door is locked.

Notes: Make sure the door frame is aligned with the door. There are no obstructions stuck in the door frame.

Install the latch and strike

• Determine backset and adjust the latch
• Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
• Install the latch
• Use a screwdriver to test if deadbolt works smoothly. 
• Install strike on the door frame.
  Important
  Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep.

Install exterior assembly

• Measure the diameter of the hole in the door.
• With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch.
• Secure the mounting plate with the supplied screws.
• Short Mounting plate screws are applied to the door with thickness of 35mm-45mm. Long Mounting screws are applied to the door with thickness of 45mm-50mm. Do not overtighten screws. 

Install interior assembly

• Push the battery cover out in the direction as illustrated. 
• Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.
• Keep the thumb turn in vertical position and install the interior assembly.
• Attach Interior Assembly to  Mounting Plate and tighten 4 Screws. 
• Load 4 AA (1.5V) batteries (included)  into the battery  compartment.

install Door Sensor

IMPORTANT
Door sensor should be mounted within 1″ (25mm) from the edge of your door, within 1″(25mm) from the top of the interior assembly

QUICK START GUIDE

At a Glance

Definitions

• Wrong Entry Limit
  After 5 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.

• One Touch Locking
  Press and hold any key on the keypad for at least 2 seconds to lock the door from outside.

• Battery Indicator
  The Battery Indicator will turn Red if the battery is running lower than 20%. Please replace the batteries as soon as possible.

• Reset Button
  Push and hold the Reset Button for 5 seconds to reset your device. After resetting, the lock will be restored to factory default settings, all settings will be disabled.

• Multifunction Button
  Push and hold the Multi-function button on the inside panel for 3 seconds to enable Privacy Mode.
  In Privacy model, all user codes access will be disabled.
  The Privacy Mode will be disabled automatically after unlocking the device with the Thumb Turn from inside or with Mechanical Key from outside.

• Type-C Port
  Power the smart lock with a portable charger via Type-C port when the batteries are completely dead.

How to Lock/ Unlock

UNLOCK the door from outside

LOCK the door from outside

UNLOCK the door from inside

LOCK the door from inside

1. Auto Lock Mode
   In Auto Lock mode, the device will be locked automatically.

2. Rotate the thumb turn to Locked Position.

Download KK Home App from the App store or Google Play.

Quick Set Up Tips

• Register an account in KK Home App
• Scan QR code on the inside panel to add KWFP01 to the device list
• Follow the setup steps to get started.

IMPORTANT:

• The Auto Lock is disabled by default, please complete the set up process and enable Auto Lock in App.
• The administrator of the lock will be the first account to bind it by default. The administrator account have access to manage users of the lock.
• To reset the smart lock, please press and hold the Reset button on the interior panel for 5 seconds.
• Log in the App with Administrator account, go to setting and unbind the lock. (This step is required, if the administrator account didn’t unbind the device, the lock won’t be able to be repaired by other accounts.)

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
To comply with FCC/IC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons.

Industry Canda Statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

Warnings

• Failure to follow the below instructions could result in damage to the product and void the factory warranty.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.

Product Care

• This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.
• Do not install batteries until the lock is completely installed on door.
• User Pin Codes: Can be 4-10 digits and can be set up in KK Home App.
• Door sensor calibration: To calibrate your door, please follow the instruction in App step by step. Once it’s calibrated successfully, you could try detect the status of your door in KK Home.
• Share your device: Share your device means that you share the access to track the device with your other users, please be aware of the potential risks ii may cause.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>