Milliard Patented Adjustable Balance Beam User Manual

Milliard Patented Adjustable Balance Beam

WELCOME TO THE FAMILY

PRECAUTION: ALWAYS READ AND FOLLOW INSTRUCTIONS BEFORE USE. ALWAYS USE THE UNIT ACCORDING TO THE MANUFACTURER’S’ GUIDELINES. ONLY USE THE UNIT IN A MANNER AS INTENDED BY MANUFACTURER

THANK YOU FOR PURCHASING OUR BALANCE BEAM AND TRUST ING MILLIARD WITH PROVIDING YOURSELF AND YOUR LOVED, ONES WHIT THE UTMOST COMFORT AND SUPPORT IN YOUR HOME.
AS A FAMILY BRAND THAT STARTED BACK IN 2009 WE’VE DEDICATED OURSELVES TO CAREFULLY CRAFTING LINES OF PRODUCTS USED TO ELEVATE YOUR HOME. QUALITY AND FAIR PRICING IS OUR PROMISE TO YOU. YOU CAN TRUST THAT IF IT’S NOT GOOD ENOUGH FOR OUR HOME, IT’S NOT GOOD ENOUGH FOR YOURS .

WARNING:

• THIS PRODUCT IS TO BE ASSEMBLED BY AN ADULT.
• THIS PRODUCT IS FOR GYMNASTICS USE ONLY.
• DO NOT USE A PARTIALLY-ASSEMBLED BALANCE BEAM.
• NOT INTENDED FOR COMMERCIAL USE.
• DO NOT EXCEED TOTAL WEIGHT CAPACITY OF 150LBS.
• DO NOT USE BALANCE BEAM IF DAMAGED.
• PERFORM ONLY ON A FLAT, LEVEL SURFACE.

DID YOUR UNIT COME WITH ANY DAMAGED OR MISSING PARTS?

We’re here to help.

OUR TEAM OF DEDICATED CUSTOMER CARE PROFESSIONALS ARE READY TO HELP YOU WITH ANY QUESTIONS OR CONCERNS YOU MAY HAVE.

FOR IMMEDIATE ATTENTION, CALL MONDAY-THURSDAY 9:OOAM-5:OOPM u FRIDAY 9:OOAM-1:OOPM.

OR YOU CAN LEAVE US A VOICE MESSAGE OR EMAIL, AND WE GUARANTEE YOU WILL HEAR BACK FROM US WITHIN ONE BUSINESS DAY.

PHONE : 866-686-4891
EMAIL: INFO@MILLIARDBRANDS.COM

PRECAUTIONS

• ALWAYS INSPECT AND TEST THE BALANCE BEAM BEFORE USE. DO NOT USE IF THERE IS DAMAGE, WEAR, OR LOOSE PARTS.
• ALWAYS USE THE BEAM WITH CONTROLLED MOVEMENTS AND BALANCE TO AVOID INJURY OR DAMAGE TO SURROUNDINGS.
• ALWAYS PROTECT THE BALANCE BEAM FROM HUMIDITY TO MAXIMIZE SERVICE LIFE.
• ALWAYS CONTACT THE MANUFACTURER OR A QUALIFIED PROFESSIONAL TO ARRANGE FOR PROPER REPAIR.
• ONLY USE THE BALANCE BEAM WITH A PADDED MAT IN PLACE BELOW THE BAR TO PREVENT ACCIDENTS OR INJURIES.
• ONLY USE THE BALANCE BEAM FORT GYMNASTICS TRAINING PURPOSES. IT IS NOT DESIGNED FOR OTHER USES.
• ONLY CLEAN THE BALANCE BEAM WITH MILD SOAP AND A DAMP CLOTH IF NECESSARY. USE NO SOLVENTS.
• ONLY USE THIS EQUIPMENT WITH PROPERLY TRAINED, QUALIFIED PERSONS UNDER SUPERVISED CONDITIONS.
• NEVER ATTEMPT ADVANCED TECHNIQUES WITH A BALANCE BEAM BEFORE COMPLETING ADEQUATE TRAINING.
• NEVER ALLOW SMALL CHILDREN ON OR NEAR THE BALANCE BEAM.
• IT IS NOT A TOY.
• NEVER CONTINUE TRAINING IF YOU EXPERIENCE SIGNIFICANT PAIN OR DISCOMFORT DURING USE TO AVOID FURTHER INJURY.
• NEVER ATTEMPT TO REPAIR OR MODIFY DAMAGED OR WORN COMPONENTS YOURSELF.

OVERVIEW

THE ADVANCED BALANCE BEAM IS FULLY HEIGHT-ADJUSTABLE AND CAN BE USED IN ONE OF TWO ” MODES”.
-FLOOR MODE: THE LEGS ATTACH DIRECTLY TO THE BEAM FOR USE WITH BEGINNERS OR GYMNASTS PRACTICING NEW TECHNIQUES.
-HIGH MODE: USING THE ADJUSTABLE LEG SUPPORTS, THE BEAM CAN BE RAISED IN 21N. INCREMENTS FROM l ½FT. TO 2FT. THIS MODE IS IDEAL
FOR ADVANCED GYMNASTS THAT ARE COMFORTABLE PERFORMING THE MOVES.
ASSEMBLY SHOULD BE COMPLETED BY AN ADULT AND THE USE OF POWER TOOLS IS NOT RECOMMENDED. USE THE INCLUDED HEX DRIVER OR BASIC HAND TOOLS TO AVOID DAMAGING PARTS.
BE SURE TO VERIFY THAT YOU HAVE ALL THE PARTS LISTED ON THE PREVIOUS PAGE BEFORE BEGINNING ASSEMBLY.

PARTS

1. BALANCE BEAM Xl’
   

2. LEG BAR X2

3. RUBBER FEET X4

4. UPPER LEG SUPPORT X2

5. LOWER LEG SUPPORT X2

6. HEIGHT ADJUSTMENT KNOB X2

HARDWARE PARTS

A BOLTS X16

B WASHER X16 EACH

C HEX KEY Xl

FLOOR MODE ASSEMBLY INSTRUCTIONS

• PLACE THE LEG BARS (2) OVER THE BOTTOM OF THE BALANCE BEAM fl). LINE UP THE LEG BARS ,(2) W TH THE HOLES CLOSEST TO THE EDGE OF THE BEAM (1). PUT THE SMALLER WASHERS (B) ON THE BOLTS (A). USING THE INCLUDED HEX KEY (C), SLIDE THE BOLTS THROUGH THE HOLES IN THE LEG BARS AND SECURE THEM 10 THE BEAM.
• SLIP THE RUBBER FEET ,(3) ONTO THE ENDS OF THE LEG BARS (2)AND FLIP THE BALANCE BEAM UPRIGIHT.

HIGH MODE ASSEMBLY INSTRUCTIONS

STEP 1

PLACE THE UPPER LEG SUPPORTS ,(4) OVER THE ATTACHMENT POINTS ON THE BEAM (1). THE HOLES FOR THE HEIGHT ADJUSTMENT KNOBS SHOULD FAC:E OUTWARDS. SECURE THE LEG SUPPORTS WITH BOLTS (A) AND WASHERS (B).

STEP 2

• ATTACH THE LOWER LEG SUPPORTS (5) TO THE LEG BARS (2) USING BOLTS (A) AND WASHERS (B).
• SLIP THE RUBBER FEET (3) ONTO THE ENDS OF THE LEG BARS.
  

STEP 3

• TURN THE BEAM UPSIDE DOWN. HOLD THE LOWER LEG SUPPORT WITH THE PORT FOR THE HEIGHT ADJUSTMENT KNOB FACING OUTWARDS.
• SLIP THE LOWER LEG INTO THE UPPER LEG. REPEAT FOR THE OTHER SIDE.
• THEN, SCREW IN THE HEIGHT ADJUSTMENT KNOBS (6) ON EACH SUPPORT UNTIL YOU FEEL GENTLE TENSION. DO NOT TIGHTEN THEM ALL THE WAY.
• PULL ON THE LOWER LEG SUPPORT ON EACH SIDE UNTIL YOU HEAR AN AUDIBLE “CLICK” AND THE LEG STOPS MOVING. NOW YOU MAY TIGHTEN THE HEIGHT ADJUSTMENT KNOB FULLY AND THE BEAM SHOULD BE LOCKED IN POSITION. YOU MAY NOW FLIP THE BEAM OVER.
  

HIGH MODE ADJUSTMENT

TO ADJUST THE HEIGHT OF THE BEAM, LOOSEN THE HEIGHT ADJUSTMENT KNOB JUST ENOUGH TO RELEASE TENSION AND THEN PULL ON THE KNOB TO RELEASE THE LOCKING SPRING. PULL THE BEAM UP OR DOWN UNTIL IT’S AT THE DESIRED HEIGHT. RELEASE THE KNOB AND LET IT CLICK INTO PLACE, THEN TIGHTEN IT DOWN TO LOCK IT AGAIN.
REPEAT FOR THE OTHER SIDE.

THANK YOU AGAIN!

YOU’VE OFFICIALLY COMPLETED ALL ASSEMBLING.
THANK YOU AGAIN FOR YOUR PURCHASE.
WE HOPE YOU’RE LOVING IT!

PHONE: 866-686-4891 EMAIL: INFO@MILLIARDBRANDS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>