ODDICT TWIG2 True Wireless Earphones User Manual
- May 15, 2024
- ODDICT
Table of Contents
ODDICT TWIG2 True Wireless Earphones
Package Contents
Pairing
- Place both earbuds in the case, close the case cover, and charge for at least 10 minutes ha fare Cucina for the first times
- Enable Bluetooth on your device and flip open the case cover. Pairing mode will be activated in 5 seconds.
- Select TWIG2 in the Bluetooth settings of your device and it will be connected to your device via Bluetooth. This procedure will need to be repeated every time you pair TWIG2 with a new device. When removing earbuds from the case, they will automatically reconnect to the last device the TWIG2 was paired with.
How to use earbuds
When the earbuds connect to your device via Bluetooth, you will hear a high- pitched marimba tone. Once you place the earbuds in your ears, you will hear a low-pitched synth tone, indicating vour device and earbuds are connected and ready to use.
Touch Controls
Double-tap • • to accept / end call.
Tap once • to play/pause.
Double-tap • • to skip to the next song.
Triple-tap• •• to skip to the previous song.
Press and release the left earbud for 1 second to activate voice assistant apps like Siri or Google Assistant.
Press and hold the right earbud for 1 second to activate 360 Spatial Audio.
Wear both earbuds, tap the right earbud once, and press again for 2 seconds to enable Ambient Mode.
How to charge earbuds
The earbuds will begin charging once they are placed in the case.
How to charge case
- Option 1. Use a USB Type-C cable
- Option 2. Place the case on the charging pad with the aluminum side facing up.
- The wireless charging coil is located in the center of the bottom case.
How to use ‘ODDICT App
1. Download and open the ODDICT App, then register or log in. Press (+), find, and select TWIG2 to add to the device
How to use ‘ODDICT’ App
2. Fine-tune your sound using the app’s EQ and experience additional features live the 260 Coatial Audial.
Compliance Information
FCC Compliance Information
FCC ID: V2R-TWIG2
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Information to the user:
NOTE : This equipment has been tested and found to comply with limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try the correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
USER CAUTION :
Changes or modifications not expressly approved by the party reasonable for compliance could void the user’s authority to operate the equipment.
USER CAUTION :
Changes or modifications not expressly approved by the party reasonable for compliance could void the user’s authority to operate the equipment.
Compliance Information
IC Compliance Information
IC : 10488A-TWIG2
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
Operating Temperature 0 – 45 ‘C (32 – 113 F
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>