DRIPRECISE 651000231 Spotlight User Guide
- May 15, 2024
- DRIPRECISE
Table of Contents
DRIPRECISE 651000231 Spotlight
Product Breakdown
| Power off state | Single Tap **** | Power On |
|---|---|---|
| Power on state | Single Tap **** | Testing |
| Single Tap **** | Calibration | |
| Hold (2s) **** | Access system information | |
| Hold **** | Power Off |
Calibration
-
Press the button to power on.
-
Spoon pure water into the sample dish.
-
Press the button ,enter the calibration state.
-
After calibration is finished, device will display “Complete”.
-
Wipe the sample dish completely dry before conducting next test.
Calibration Notes
- .Before calibration, make sure the sample dish is clean.
- Room temperature water is recommended for calibration.
- It is recommended to wait 5 seconds after spooning water into the sample dish before calibrating.
Testing
-
Press the button to power on.
-
Spoon cooled liquid to be measured into the sample dish.
-
Press the button enter the testing state.
-
Result will display on screen.
Testing Notes
- If testing a liquid continuously, it is recommended to wait at least 3 seconds between each test.
- Accurate results can be achieved within the range of 5℃-45℃ ( 41℉-113℉ ).
Cleaning
-
Use clean water to rinse the glass at the bottom of the sample dish.
-
Use a dry towel or tissue to wipe the dish completely dry.
NOTE
For more accurate results, be sure to rinse the sample dish and wipe dry after every test.
Certifications
-
Press and hold the button to access the PU information view.
(You can scan the code to connect the device with App) -
On the page, press the button to enter the PU certification view.
Draperies
Compliance Information CE Compliance Notice
EU regulatory conformance:
RF exposure information: The EIRP power of the device at maximal case is below
the exempt condition, 20mW specified in EN62479: 2010. RF exposure assessment
has been performed to prove that this unit will not generate the harmful EM
emission above the reference level as specified in EC Council Recommendation (
1999 / 519 / EC ).
CE DOC:
Hereby, Shenzhen Digitizing Fluid Technology Co., Ltd. declares that the radio
equipment type 0155B is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
www.driprecise.com/support/document
Manufacturer information:
Company name: Shenzhen Digitizing Fluid Technology Co., Ltd.
Address: Room 1602, Jinhua Building, Longhead District, Shenzhen, China.
Operation temperature: 5℃-45℃
Operation frequency(Max power)
Bluetooth: 2402-2480(9dBm)
Federal Communication Commission (FCC) Radiation Exposure Statement The device
has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction Federal Communication
Commission (FCC) Radiation.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or changes to this
equipment. Such modifications or changes could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
FCC ID:2A26IDFT-0155B
Certifications
-
Press and hold the button to access the PU information view.
(You can scan the code to connect the device with App) -
On the page, press the button to enter the PU certification view.
User Information
User Name
User Address
Phone Number
Product Information
Product Name
Serial Number
Sales Date
Sales Unit Information
Name Of Sales Unit
Sales Unit Address
Customer Support
Shenzhen Digitizing Fluid Technology Co., Ltd.
Room1602, Jinhua Building, Longhead District, Shenzhen, China.
(+86)0755-23761557
www.driprecise.com
Thank you for purchasing our product. Please contact us with any questions!
Scan here to check quality assurance regulations
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>