OEF Furnishings 600SERIES Mobile Floor Lectern with Side Shelf And Keyboard Tray Instruction Manual

OEF Furnishings 600SERIES Mobile Floor Lectern with Side Shelf And

Keyboard Tray

Product Information

• Specifications
  • Product Name: 600 Series Aristocrat Non-Sound Lectern
  • Manufacturer: National Public Seating
  • Model: 600 Series

Product Usage Instructions

• Parts List

  • A – Front Panel
    B – Side Panel
    C – Side Panel
    D – Panel
    E – Panel
    F – Bottom Panel
    G – Shelf Runner Panel
    H – Shelf Runner Panel
    I – Keyboard Sliders
    J – Phillips Screw

• Assembly Instructions

  • Assembly Tips:
  • Read instructions carefully and follow diagrams for correct assembly.
  • Avoid using sharp instruments to open the packaging.
  • Assemble on a clean, protected surface.
  • Tools Needed:
  • Phillips Screw Driver
  • Hammer
  • Hardware Included:
  • Wooden Dowels x8
  • Cam Bolts x17
  • Cams Locks x17
  • Non-Locking Casters x2
  • Locking Casters x2
  • Keyboard Sliders x2
  • 1/2” Phillips Screw x32
  • Corner Braces x2
  • Plastic Glides x2
  • Installation of Hardware:
  • Lay out the wood panels with factory-drilled holes facing upwards.
  • Screw bolts into predrilled holes using a Phillips Screwdriver.
  • Insert cams into designated holes with arrows pointing to the closest edge.
  • Assembly of Lectern:
  • Align panel edges with cam bolts and tighten cams until locked.
  • Attach casters to the bottom panel as instructed.
  • Install shelf frames as per diagram instructions.

FAQs

• Q: What should I do if I encounter missing parts during assembly?
  • A: In case of missing parts, please contact our customer service at 1-800-261-4112 for assistance.
• Q: Can the lectern be easily disassembled for storage or transportation?
  • A: Yes, the lectern can be disassembled following the reverse steps of the assembly instructions for convenient storage or transportation.

ASSEMBLY TIPS

• Read the instructions carefully and follow
• Diagrams to ensure an easy and correct assembly.
• Do not use a sharp instrument such as a Knife or a Screwdriver to open the packaging, as this may scratch or possibly damage the unit.
• All assembly should be done on a clean protected surface such as carpet or the like.
• Make sure that you have all the required Parts listed below.

TOOLS NEEDED

PARTS

HARDWARE INCLUDED

INSTALLATION OF HARDWARE

1. Lay out the wood Panels as shown in Diagram A (make sure the factory-drilled holes are facing upwards). You can determine the top of the front Panel by identifying the “T” molding edge.
2. Identify the holes numbered 1 in Diagram A. Screw the Bolts 2 into the predrilled holes with the Phillips Screwdriver 1O. Be sure to tighten the Bolts all the way. (See Figure 1)
   • Be careful not to over-tighten the Bolts as this 1 will strip the Wood.
3. Insert the Cams 3 in the larger holes as shown on the Diagram. MAKE SURE THE ARROW ON THE CAM IS POINTING TO THE CLOSEST EDGE AND ALIGNED WITH THE HOLE ON THE EDGE. (See Figure 1)
4. Insert the eight Wooden Dowels 1 into the holes of the edges on the two “Shelf Runner Panels” g and h. You can use a Hammer 11 to insert them.
5. On the Bottom Panel f screw in the four Casters. The Locking Casters 5 should be screwed into the bottom closest to the shaped finished edge. The second pair of Non-Locking Casters 4 should be attached closest to the unfinished edge.
6. Screw in the Corner Brace 7 to the side, there are pre-drilled holes to guide you.
   • DIAGRAM “A”

ASSEMBLY OF LECTERN

The instructions of the Assembly must be followed carefully.

1. Align the holes on the edge of the Panel b edges with three Cam Bolts 2 on the side panel a. Tighten the Cams by turning clock-wise until locked. (See Diagram B and Figure 1)
2. Take Panel d and Panel e and tighten Cams 3. Make sure the Cams on Panel d and Panel f face the bottom of the Lectern. The two Bolts 2 just above the slots align with the two holes on the edge of Panel d (these holes reach until de Cams). The two Bolts in the centre of the right side Panel will align with the two holes on the edge of Panel e. Gently push the Panel down onto the Cam Bolts until the Panel is completely on the right-side panel.
   • Figure 1
   • DIAGRAM “B”
   • DIAGRAM “C”
3. Taking the Panel f , with the Casters 4 5 facing the bottom of the unit, insert Panel into the groove, and make sure that the Panel is in the groove. (See Diagram B)
4. Next to be installed will be the Shelf Frames. Identify the Runner Panel with one edge cut on an angle (Panel g ) (See Diagram C ). Now the second Shelf Runner Panel (Panel h ) shall be installed under Panel d and near Panel b with the Plastic Glides 9 facing the other side.
5. Now apply Panel c to the semi-assembled unit. Be sure to align the Cam Bolts to the holes on both Panel b and Panel e. Be sure that Panel f is securely in the groove. Tighten Cams. (See Diagram D)
6. Screw the Corner Braces 7 in Panel into f Panel a and Panel c. There are pre-drilled holes to help guide you.
7. Slide Panel 1 into the slots on the side of the unit. Make sure the two Pilot holes are facing the bottom. Tap the two plastic Glides 9 into the Pilot holes AFTER THE SHELF IS FULLY INSERTED IN THE SLOTS. (See Diagram E)
   • DIAGRAM “D”
   • DIAGRAM “E” KEYBOARD INSTALLATION
   • A. Install three Cam Locks 3 into the three pre-drilled holes with the Cam Locks Arrows facing the holes.
   • B. Install the three Cam Bolts 2 into the Keyboard Lips j1 pre-drilled holes.
   • C. Align the Cam Bolts with the Cam Locks and fasten using Phillips Screwdriver 10. (See Figure 1)
8. Extend the pre-installed Keyboard Sliders 6 on Panles a and c , and attach them to the Keyboard tray (Panel j ) using three Screws 8 on each side.

Double-check that all Bolts and Screws are tightened securely before use. Check all Bolts and Screws periodically. Failure to completely tighten the Bolts and Screws may result in tipping and possible injury!

Congratulations, your ARISTOCRAT NON-SOUND LECTERN is now assembled and ready to be used!

Dear Customer,

• Thank you for your purchase. Although extreme care goes into the manufacturing & packaging of this product, mistakes are possible.
• If you encounter any missing parts or difficulty in assembly, please contact our customer service Toll-Free at 1-800-261-4112 or
• info@nationalpublicseating.com for a courteous & immediate resolution to your problem.
• www.nationalpublicseating.com
• 1-800-261-4112

References

• nationalpublicseating.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>