Bad Bird Bikes Cuervo Negro Bad 1500 Watt Powerful Motorcycle User Guide
- May 15, 2024
- Bad Bird Bikes
Table of Contents
User guide
Bike Assembly
Unboxing and Bike Assembly.
Step 1. Please open the box from the top. There will be a small box inside.
Please remove that box and open the small box. It will include the battery,
charger, rear pegs, and bike lock.
Step 2.Open the side of the box vertically down
on each side with a razor blade.
Step 3. Remove the front wheel from the
packaging, and remove the temporary bolt inside the front forks. Install the
wheel on the front forks. Make sure the brake rotor is aligned.
Tighten up with the tool provided or use a 15mm wrench.
Step 4.Flip the
bike over so it stands its wheels.Now remove all the packaging.
Step 5. Install
the M5 controller screen and button onto the handlebars. Loosen the small
Allen screws with the multi tool provided. The controller screen will be in
the middle of the handlebars and button on the left side of the
handlebar.
Step
6. Install the handlebars. Please use the Allen wrench multi tool to remove
the 4 Allen bolts. Remove all 4, install handlebar, and install the 4 Allen
bolts. Please adjust the handlebars to be in the center and make sure the
controls on the left side are vertical.
Step 7. Install the front fender above the
front wheel. Bolt is in the front forks.
Step 8. Install the headlights. 1 bolt on each
side.
Step 9.
Make sure all the wires are clear behind the headlight. Move the wires and
brake lines as needed. Step 10. Please use the Allen wrench multi tool to
adjust the brake levers up or down as needed. As well as the gear shifter can
be adjusted.
Step
11. Install the pedals. Make sure you install the correct ones. The left pedal
has reverse thread and is stamped L on the inside of the pedal. Use the tool
provided or a 15 mm wrench.
Step 12. Install the rear pegs. Use the lower
holes on each side. And use a 14 mm wrench to tighten. You can very Carefully
cut the zip tie that holds the wire to the motor. Be extremely careful and do
not cut the wire. Afterwards, use a zip tie to secure the motor wire once
again.
Do Not! I repeat, Do Not loosen or remove the rear wheel or rear wheel nut. If
these nuts are loosened or removed the bike warranty is void.
Step 13. Install
the battery by unlocking it first and then sliding it down. Then lock the
battery and remove the key.
Step 14. Please Be sure to inflate the tires
to 20 psi. Step 15. Please charge the battery for 4-6 hours before the first
use. Make sure the battery switch is in the off position, then plug the
charger into the battery, and then plug the charger into a power outlet. Once
charged fully,the light will turn green and the bike is ready to use.
The charger and bike are not waterproof. Do not charge or ride in wet
conditions.
M5 Con troller
LCD Display M5 User Manual
Latest Version 2023
-
Functions
Turn the battery switch to the on position. Then hold down the center button for 2 seconds. The screen should turn on and light up. To turn off, hold the center button for 2 seconds.
a. Display
Speed Display, PAS Level Display, Battery Level Display, Error Indication, Total Mileage, Single Mileage, Single Running Time Light Signal
b. Control and Settings
Power Switch, Front Light Control, 6km/h Inching Control, Wheel Diameter Setting, Top Speed Setting, Auto-Hibernation Interval, Backlight Brightness Setting, Voltage Level Setting
c. Communications Protocol: UART
Display Readings (display at start for 1 second)
Display Details 1.1 Light
Turned on manually or environment-sensed (requires light-sensitive support)
1.2 Battery Level 1.3 Multi-Functions Display ©[D OTE%
Total Mileage: ODO
Single Mileage: TRIP A
Single Mileage: TRIP B
Current Voltage VOL
Operating Current: CUR
Display Booting Time: TM
1.4 Riding Mode
Walk: Walking Boost
Cruise: Constant Speed Cruise PAS: Power Assist Level (0-9 Adjustable) 1.5 Speed Display
Maximum Speed: MAX
Average Speed: AVG
Measuring Unit: MPH or KM/H
The display will calculate the actual travelling speed based on the wheel diameter and signal data. -
Buttons
Arrangement of buttons on the panel: Introduction of buttons
Button operations involve short press, long press and long press of combination keys.
Short press is used for short/frequent operations as:
1. Short press either of these keys to change power assist speed during riding.
2. Short press this key **** to switch the readings in the multi-function display section.
Long press on a single key is used to switch mode/on/off status.
Long press on combination buttons to set parameters, which can avoid problems (short press on combination keys is disabled, for it’s easy to induce problems and hard to manipulate).
Detailed Instructions
1. Change Assist Power/ Electric Gear
In assist power mode
a. Short press , assist power +1.
b. Short press , assist power -1.
2. Switch Speed Display
Long press to switch speed display type.
3. Enable / Disable 6km/h cruise, set real-time cruise and turn on/off the lights
When the vehicle is parked, long press to enter 6km/h cruise mode.
When the vehicle is parked, long press to enter real-time cruise
Long press to exit the cruise mode when the vehicle is in cruise mode.
Long press to turn on/off the lights.
4. Turn on/off the LCD Panel
When the display panel is operating, long press and it will be turned off, otherwise it will be turned on.
5. Switch Displayed Readings in Multi-Functions Section Short press to switch readings shown in the multi-functions section. -
Vehicle Status
Error Code and Indications
| Error Code (decimal) | Indications | Note |
|---|---|---|
| 0 | Normal | |
| 1 | Reserved | |
| 2 | Brake | |
| 3 | PAS Sensor Failure (riding mark) | Not Realized |
| 4 | 6km/h Cruise | |
| 5 | Real Time Cruise | |
| 6 | Low Battery | |
| 7 | Motor Failure | |
| 8 | Throttle Failure | |
| 9 | Controller Failure | |
| 10 | Communications Receiving Failure | |
| 11 | Communications Sending Failure | |
| 12 | BMS Communications Failure | |
| 13 | Light Failure |
3.1 Settings
PO1: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class: 24V / 36V (default) / 48V
P04: Hibernation Time (0: never, other figures refer to the hibernation time)
Unit: minute
P0O5: PAS Level – 0/3 Gear Mode
1/5 Gear Mode
P06: Wheel Diameter Unit: inch Precision: 0.1
- To get accurate speed display, this parameter should be correct.
P07: Magnet Steel Number for Speed Test Range: 1-100 - To get accurate speed display, this parameter should be correct.
Gear-less Motor: the value is the magnet steel humber.
Geared Motor: the reduction-gear ratio is required. The value = magnet steel number*reduction-gear ratio.
For example, magnet steel number is 20, reduction-gear ratio is 4.3. The value input is: 86=20×4.3
P08: Speed Limit
Range: 0-100km/h, parameter 100 indicates no speed limit.
This parameter limits the max. speed of the vehicle.
For example, input value 25 means the max. speed is 25km/h, the vehicle travelling speed can only reach the preset value.
Deviation: +1km/h (applies to both PAS and throttle mode).
Note: The above-mentioned values are measured by metric unit (kilometers). When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.
IMPORTANT: P09-P15 only works under communications mode.
P09: Zero / Non-zero Start Setting:
0: Zero Start
1: Non-zero Start
P10: Drive Mode Setting
0: Power Drive — The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
1: Electric Drive — The vehicle is driven by the handlebar. In this status the power gear does not work.
2: Power Drive + Electric Drive – Electric drive does not work in zero-start status.
P11: PAS Sensibility Range: 1-24
P12: Assist Power Intensity Range: 0-5
P13: Power Magnet Steel Number: 5 /8 / 12pcs
P14: Current Limit Value: 12A by default; Range: 1-20A
P15: Unspecified
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>