NOUVEL 5994137 Bonita Buy Pellet Heater User Manual

: May 15, 2024
: NOUVEL

Table of Contents

Introduction
Safety instructions
Safety instructions
Commissioning
Operation
Cleaning and maintenance
Transport and storage
Disposal
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NOUVEL 5994137 Bonita Buy Pellet Heater

NOUVEL 5994137 Bonita Buy Pellet Heater

Introduction

We are pleased that you have chosen the pellet radiant heater Bonita and thank you for your confidence in our products. Please take a moment to read this user manual carefully before using the product for the first time. This will enable you to make the best use of your appliance from the point of view of safety and efficiency.

Safety instructions

Symbols

These INSTRUCTIONS contain the necessary information for the use and maintenance of the appliance. Please follow these provisions in order to use the appliance safely and correctly. This installation and user manual is an essential part of the product: make sure it is always supplied with the appliance.

Symbol Non-compliance will affect the use of the product.

PERSONAL SAFETY: This safety symbol indicates important information. Read the following information carefully, as failure to follow the instructions may cause may cause serious harm to persons using the appliance.

PROHIBITION: This symbol categorically forbids the operation or situation described in the described in the information. Failure to comply may permanently damage the unit or cause or cause serious injury.

Safety instructions

Risks and dangers

The unit has been designed to minimise the risks for the user and maintenance personnel. It is technically impossible to completely eliminate the causes of danger, which is why it is essential to observe the following instructions.

Children and disabled persons are not allowed to use the appliance without assistance.
It is forbidden to tamper with the safety or adjustment devices or to make any other changes without the manufacturer‘s permission.
It is forbidden to use the appliance as an incinerator or to use it in any way other than as it was built.
It is forbidden to place items of laundry or clothing on the appliance to dry; any drying racks must be placed at a minimum distance of 2.0 metres from the appliance to avoid fire hazards.
It is forbidden to open the appliance door during the switch-on, operation and switch-off phases.
It is forbidden to operate the appliance if the glass of the combustion chamber is broken.
It is forbidden to clean the glass and all hot parts while the appliance is in operation.
It is forbidden to touch the appliance while it is in operation or when it has not yet cooled down completely, as some parts (handle, door, glass, etc.) may cause burns. If necessary, use protective clothing (e.g. gloves, etc.).
It is forbidden to use other fuels to power or ignite the appliance.
It is forbidden to bring flammable materials near the appliance (example: bags of pellets, flammable liquids, pellets, flammable liquids, etc.).
Children must not play with the appliance, even if it is switched off. Cleaning and maintenance must be carried out by the user or by qualified personnel.

Commissioning

Reception

On receipt, check that the unit has no breaks or dents and that the model corresponds to the information on the transport document. Any damage, incomplete or non-conforming deliveries must be reported immediately to the manufacturer or the dealer the dealer immediately.

Do not leave the packaging material in the hands of children as it can be a source of danger. can be a source of danger. The proper disposal of the packaging material is the responsibility of the user.

Dimensions

Dimensions

Scope of delivery

Quantity	Description	Image
1	Handle large	![Commissioning](https://manuals.plus/wp-

Supplied

Quantity| Description|
---|---|---
16| M6 washer|
16| Allen round screws M610|
8| Allen round screws M616|
4| Allen screws countersunk M616|
4| Phillips slotted screw M412|
8| Silikon Pads|
1| M6 spanner|

Mounting

Step 1 : Use 16 M6*10 Allen screws, 16 flat pads, attach 2 wheels without brakes at the front and 2 wheels with brakes at the rear.
Step 2: Use 4 M616 Allen screws and 4 M412 Phillips screws with a large flat head to align and secure the 4 glass holders to the edges.
Step 3 : Use 4 M6*16 countersunk screws to attach the centre partition to the oven housing.
Step 4 : Insert 4 glass panes into the slot in the bracket.

Assembly

Step 5 : Insert 8 silicone pads into the slot in the holder to secure the glass.
Step 6 : Use 4 x M6*16 Allen screws to secure the top cover.
Step 7 : Place the ashtray in the centre of the card slot inside the housing.
Step 8 : First snap the handle into the combustion tube. First insert the combustion tube parallel upwards into the heating chamber and then insert it flat into the holder provided. Then remove the handle.
Step 9 : Insert the power bank.

Operation

Standout

When the pellet heater is in operation, the glass and the door in particular become very HOT! Therefore, ensure suitable measures or protective measures against accidental contact and fire hazards.
CAUTION! Some parts of this product can become very hot and cause burns! Special care should be taken when children and vulnerable persons are present. The appliance is extremely hot during and immediately after operation. NEVER touch or move the appliance during or immediately after operation.
The pellet heater may only be used outdoors! Otherwise toxic fumes can accumulate which can lead to serious, health damage or even death (carbon monoxide poisoning). Therefore, never use the charcoal grill in a flat, garage, tent, caravan or other closed rooms.
The pellet stove is intended exclusively for use outdoors or in semi-open spaces such as verandas or pergolas.
It is imperative that the unit is set up on a level surface that is sufficiently load-bearing for the unit and that the weight is evenly distributed.
IMPORTANT! Place the appliance only on a fireproof floor or base. Use of the appliance is not recommended in unfavorable conditions (strong wind, heavy rain, snow). Use of the appliance is not recommended.
Keep a safe distance from flammable materials, flammable gases and liquids (petrol, alcohol, gasoline)and liquids (petrol, alcohol, methylated spirits).
The exhaust gases produced by the appliance must be discharged directly into the atmosphere, they are not necessarily visible, but they are very hot and can cause fires or burns.

Before start-up

All preliminary checks must be carried out each time the unit is ignited for the first time or after a longer period of non-use.
Check that the safety distances have been observed when setting up the unit!
Check that there are no flammable materials in the vicinity of the unit. (see section «Safety distances»).
In case of ignition after a long period of non-use, all parts of the fireplace, the glass and the fan area must have been checked and cleaned of ash and dust before use.
Make sure that there are no flammable materials in the combustion chamber (documents, cables, paper, etc.).
Make sure that the power bank (battery) is fully charged.
Check that there are no obstructions at the top of the appliance near the smoke outlet.
Check that the unit is flat, stable and perfectly vertical.

Safety distances

When the unit is used under movable structures, such as: Canopies, canopies, gazebos, curtains, or under trees, plants or other vegetation, it is imperative to It is imperative that the following safety distances are maintained:

A Lateral distance 200 cm
B Distance above 200 cm
Commissioning

The installation distances must be observed for reasons of safety and fire protection. If the floor is made of combustible material (e.g. wood, carpet, rubber, plastic), sufficiently dimensioned floor plates (sheet metal, glass) must be used to protect the wooden floor.
It is forbidden to place flammable materials near the appliance (example: bags of pellets, flammable liquids, etc.).

Safety glass

Do not use the appliance in the rain as the glass protectors may break if they suddenly come into contact with water. Always switch off the appliance when it is raining. Do not spray liquids on the glass while the appliance is in operation. The glass is extremely hot during operation, do not try to touch it and keep children away from the appliance. Always make sure that the appliance is in a stable position. If the appliance falls to the floor, the glass protectors may break. Do not use the appliance if the glass is broken or damaged.

Power bank (Battery)

To control the heat output and achieve an optimal flame pattern, this pellet heater is equipped with a fan. This draws its energy from an integrated, rechargeable battery (power bank).
Before each ignition, check that the Power bank is charged. The charging status is determined by checking the LED lights on the powerbank itself.

To charge the power bank, make sure the unit is cold and proceed as follows:

Open the flap and disconnect the cable from the power bank
Remove the power bank.
Connect the supplied charger to the powerbank.

NOTE! Disconnect the power bank at the end of the operating cycle. Only use the power bank supplied with the unit to operate the unit. If this is defective or additional power banks are required, please contact the dealer or the manufacturer.

Specification of the pellets

The fuel used is called pellets and is a pressed wood sawdust granulate. The exclusive use of quality pellets, preferably from local production, results in an almost neutral environmental impact in terms of CO2, high efficiency and less ash accumulation inside the appliance.

Below you will find the reference parameters for a high-quality pellet:

```
* Diameter = 6 – 8 mm
```
- Length = 10 – 30 mm
- Maximum moisture content 8%
- Ash residue: less than 1%
- Density: 650 kg / m³
- Minimum calorific value: 4.9 kWh per kg / approx. 18000 kJ per kg
- Raw material: only natural wood, free from chemicals or residues. If binding agents are present, these may only be of natural origin and in minimal quantities.
It is prohibited to use the appliance as an incinerator or to use it in any other way in any way other than the way in which it was built.
It is prohibited to operate or commission the appliance with other fuels.
The use of fuel that does not comply with the above specifications will not only immediately invalidate the warranty for the appliance, but may also lead to dangerous situations.
The manufacturer is not liable for poor performance of the appliance caused by inadequate quality of the pellets.

Filling with pellets / lighting

Before each START, check that the powerbank is charged.
Open the door, take out the pellet container with the special handle and clean the container and the fireplace if necessary.
Pour the pellets into the container to a distance of 3 cm from the top.
Cover the pellets with two to three pieces of lighting wool.
Follow step 7 of the installation steps above to place the combustion barrel in the stove body as required.
Check that the pellet container is positioned correctly.
Connect the power bank to the USB port.
Turn the wind speed adjustment switch clockwise to the desired value.
Open the ignition opening cover on the side of the main body, light the flame with a long match (>20cm) or a gas lighter with a long neck and close the ignition opening cover.
Close the door.
After switching on, the desired flame size can be adjusted by changing the fan speed.
To avoid burns, care must always be taken not to touch the combustion drum or the surrounding metal housing with the hands. It is recommended to wear heat-resistant gloves for manipulations on the fan.
No user intervention is required during the entire operating time, which is approximately 2.0 to 3.5 hours. The entire pellet load is first burnt through the pyrolysis process and then, in the final phase, through the gasification process (indicated by a blue flame).
Make sure that the fan is running all the time, otherwise the flame may go out.
At the end of the operating cycle, the flame goes out by itself without any external intervention. The appliance then enters the cooling phase, which can last 20 to 40 minutes. At the end of the cooling phase, the burner can be refueled.
After firing has been completed, the pellet charge must be burnt completely. The process must not be interrupted.
NOTE! During the first ignition, certain manufacturing residues may still be burnt. This odour may be unpleasant but not harmful. In the course of further use, these possible odour emissions disappear completely
It is normal for a minimal amount of ash to remain in the fire tube after each operating cycle. This must be removed before the next start.

Cleaning and maintenance

Introduction

As your appliance runs on pellets, it must be checked and cleaned regularly. Regular maintenance ensures smooth operation and optimum performance.
The user must clean the appliance regularly as described in these instructions.
Do not use aggressive or abrasive products for external cleaning. Do not wash the unit with water or other liquids, as these could damage the internal electrical wiring and thus endanger the user.
WARNING: Do not get the appliance wet and do not touch the electrical parts with wet hands. touch with wet hands.
Never suck up hot ashes – the hoover used could be damaged.
All cleaning and maintenance work must be carried out when the appliance is completely cold and the power bank is disconnected.

Intervall

****Unless otherwise stated, the operations listed below are compulsory and cannot be postponed beyond the specified time.
Clean the pane with a cotton cloth or kitchen paper and a special glass cleaner for stoves and fireplaces. Glass cleaner for stoves and fireplaces if the glass has soot residue.

Before each refill

Remove the burner/pellet container and clean it with a brush.
Clear the openings at the bottom of any blockages caused by combustion residues. If necessary, remove the burner tube and clean it with a wire brush and, if possible, a hoover.
CAUTION: If an ash extractor is used, make sure that no embers are burning and that the ash is cold.
Remove the pellet tank and clean the socket of the tank inside the appliance; especially also the insulating plate.
After cleaning and for each load, it is recommended to pay very careful attention to the correct installation of the tank in the appropriate seat.
The use of certified and therefore high quality pellets allows the appliance to operate correctly at the specified output and cleaning and maintenance work is less onerous. The presence of silica agglomerates on the bottom indicates poor fuel quality (see above).

Weekly

Vacuum the compartments inside the appliance and underside of the metal casing.
Check the flue connections and make sure they are clean and free of blockages.

End of season maintenance

If the unit is switched off for a long period of time, it is advisable for YOUR SAFETY to disconnect the power bank it is advisable to disconnect the power bank.
We also recommend a thorough cleaning of the appliance to remove all combustion residues. Clean the ventilation unit with a brush and hoover at least once a year.
ATTENTION: Only ORIGINAL SPARE PARTS may be used!
ATTENTION: The combustion chamber must be cleaned according to the above specifications.
Flammable products must never be used for this purpose. Flammable products can lead to dangerous situations. Lack of maintenance or improper maintenance will cause the appliance not to work properly. Any problems resulting from poor cleaning or maintenance will immediately void the warranty

Transport and storage

The unit’s casing must always be transported in a vertical position. Special care must be taken to protect the glass and all sensitive parts from mechanical shocks that could affect their integrity and proper functioning.
The appliance and all accessories such as steel, glass or stone coverings must be stored in closed and moisture-free rooms. Do not stack the units on top of each other. Handle the boxes in which the units are packed with care.
It is recommended to store the product if it will not be used for a long time.

Disposal

At the end of its useful life, the product cannot be disposed of with household waste but must be scrapped in compliance with the environment and applicable regulations. The product must be de livered to suitable reception centres for the separate collection of waste. These centres are usually set up by the municipal administrations. Proper disposal not only protects the environment, but also promotes the recovery and recycling of materials.

Customer Support

Nouvel AG
Industrie Grund | CH-6234 Triengen | Switzerland
Phone +41 41 935 55 55 | Fax +41 41 935 55 66
E-Mail: [email protected] | Internet: www.nouvel.ch

Logo