CARAUDIO-SYSTEMS RL-MFD3 Camera Interface User Manual
- May 15, 2024
- CARAUDIO-SYSTEMS
Table of Contents
CARAUDIO-SYSTEMS RL-MFD3 Camera Interface
Product Information
Specifications:
- Rear-view camera-input compatible with navigation systems
- Compatible with Volkswagen RNS510, RNS315, RNS810, and radio RCD510
- Compatible with Skoda Columbus and radio Bolero
- Compatible with Seat Trinax
- For vehicles WITHOUT factory rear-view camera
- Version: 29.03.2023
Product Usage Instructions
Prior to Installation
Delivery Contents
Take note of the SW-version and HW-version of the interface boxes and store
the manual for future support.
Check Compatibility of Vehicle and Accessories
Ensure compatibility with the vehicle’s navigation system, factory-TV-
tuner, OPS, and after-market rear-view camera.
Installation
- Plug harness RLC-VN03 into the 12-pin Molex of Interface-box RLC-M02.
- Connect the female 26-pin AMP connector of RLC-VN03 to the male 26-pin AMP-connector of the head-unit.
- Connect the red cable of harness RLC-VN03 to +12V reverse gear light (recommend connecting through a relay to avoid signal noise).
- Connect the black cable of harness RLC-VN03 to ground.
FAQ
-
Can I install this product in a vehicle with a factory rear-view camera?
No, this product is only compatible with vehicles WITHOUT factory rear-view cameras. -
What should I do if the software of my vehicle is updated and causes malfunctions?
Contact our technical support for free software updates within one year of purchase. Labor costs for updates are not covered. -
Is it legal to watch moving pictures while driving with this product?
No, it is prohibited by law. The product should only be used while standing or displaying fixed menus or rear-view-camera video when the vehicle is moving.
Legal Information
- By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
- Changes/updates of the vehicle’s software can cause malfunctions of the interface. We offer free software-updates for our interfaces for one year after purchase. To receive a free update, the interface must be sent in at own cost. Labor cost for and other expenses involved with the software-updates will not be refunded.
Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources.
Delivery contents
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
Check compatibility of vehicle and accessories
- Requirements
- Vehicle Volkswagen, Skoda und Seat
- Navigation RNS510, Columbus and Trinax (all with min. Version B with SW 1100), RNS315 and RNS810 navigation systems RCD510 and Bolero radio WITH 26pin connector on the rear of the head-unit
- Limitations
- Factory-TV-tuner Must NOT be installed.
- Coding The head-unit must be coded to rear-view camera per diagnosis computer or the RNS510, RNS315 and the RCD510 with our optional available OBD-coders OBD-VW-R-xx (OPS, too).
- OPS On vehicles with OPS (optical parking system) the OPS control box must be coded to rear-view camera per diagnosis computer.
- After-market rear-view Only compatible with NTSC-cameras.
Connection schema
Installation
- Switch off ignition and disconnect the vehicle’s battery! If according to factory rules disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead.
- Place of installation is behind the head-unit.
Interconnecting Interface-Box, harness and head-unit
- Plug harness RLC-VN03 into 12pin Molex of Interface-box RLC-M02.
- Plug female 26pin AMP connector of RLC-VN03 into male 26pin AMP-connector of head-unit.
- Connect red cable of harness RLC-VN03 to +12V reverse gear light (we suggest to connect through relais to avoid signal noise) and black cable of harness RLC-VN03 to ground.
Note: If the 26pin AMP-socket of the head-unit is already occupied, the vehicle probably has a factory rear-view camera or a factory TV-tuner. In case of a factory tuner, it must be uninstalled: disconnect the female 26pin AMP- connector of the factory harness and disconnect all wires from the factory TV- tuner. In case of a factory rear-view camera you have ordered/received the wrong product, call for support.
Connections to after-market rear-view camera
-
Connect the video RCA of the after-market rear-view camera to female RCA connector of harness RLC-VN03.
Note: Only compatible with NTSC-cameras. -
The head-unit must be coded to rear-view camera per diagnosis computer or for RNS510, RNS315 and RCD510 with our optional available OBD-coders OBD-301-R
(OPS, too). -
RNS510/810: If coding is done by diagnosis PC, code rear-view camera to “LOW” in controller 56 radio (not in controller 19 – CAN gateway). After coding the vehicles needs to be locked to reach sleep mode (30 seconds up to 66 minutes depending on vehicle).
-
RNS315: If coding is done by diagnosis PC, code to rear-view camera in controller 37 navigation (not in controller 19 – CAN gateway). After coding the vehicles needs to be locked to reach sleep mode (30 seconds up to 66 minutes depending on vehicle).
Vehicles with OPS (optical parking system):
If coding is done by diagnosis PC, code to rear-view camera in controller 10
park assistant 2 (not in controller 19 – CAN gateway). After coding the
vehicles needs to be locked to reach sleep mode (30 seconds up to 66 minutes
depending on vehicle).
Specifications
- Operation voltage 10.5 – 14.8V DC
- Stand-by power drain 0mA
- Operation power drain 200mA
- Power consumption 2.8W
- Temperature range -30°C to +80°C
- Weight 53g
- Measurements (box only) B x H x T 72 x 23 x 50mm
Technical Support
- Caraudio-Systems Vertriebs GmbH
- manufacturer/distribution In den Fuchslöchern 3
- D-67240 Bobenheim-Roxheim
- email support@caraudio-systems.de
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered trademarks ® of their corresponding legal owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>