YINVANI DS01 Frameless Double Sliding Shower Door Instruction Manual

**YINVANI DS01 Frameless Double Sliding Shower Door Instruction Manual

**

PARTS LISTING

Aluminum punch template
(If missing or broken, please refer to page 8 for punch data.)

Wall Bracket

Anti Collision Block

Roller

Handle

Guide Block

Glass Fastener

Glass Bracket

Guide Rail

Door Seal

Glass

Anti-Splash Threshold

Screw & Allen key

NOTES BEFORE INSTALLATION

1. Prepare the tools. (Please refer to page 6)
2. All measurements and installation should do after the wall and shower base were completed.
3. Make sure shower base is horizontal and both wall are vertical, if shower base not horizontal or the wall not vertical, please contact our installation support.
4. Understand the names and uses of individual accessories of shower door. (Please refer to page 2~4)
5. Installation by licensed professional contractor is recommended.
6. Please watch installation video or call us for installation support.  (Link:https://youtu.be/hNeOuzxqyYw)
7. To stretch width or cut the guide rail, Please contact us first to get installation support.
8. Fixed glass protect corners can be removed during installation to avoid hard removing them after installation, but you need to handle them carefully to avoid breaking the glass.Sliding glass protect corners do not remove during installation.
9. Tile walls are best to replenish some glass glue at the tile seams to avoid leakage after the installation is completed.

TOOLS REQUIRED

(we offer) Aluminum punch template

Spirit level

Tape measure

Power drill

Screw driver

Drill Bits 5/16″

Pencil

Rubber hammer

Hacksaw

Silicone Unmodified Silane(Silyl) Polymer

INSTALLATION STEPS

Measuring
Punching
Wall bracket
Guide rail
Roller
Fixed Glass
Glass guide block
Slide Glass Roller
Handle Door seal
Bottom anti-splash threshold
Gluing

1. There are 2 kinds of aluminum punch templates, suitable for left or right-opening,2 kinds of random shipping. Punch rules: the bottom fixed glass bracket perforation position needs to be 1″ outside the vertical surface of wall bracket punch position, to ensure that the fixed glass is installed on the outside of guide rail. The attached aluminum template is for reference, if punch method and opening is consistent with the illustration, punch templates can be used, if not please refer to step 2 of punch data. Please measure with horizontal ruler, draw the punching point position after ensuring the slope value.

2. 2 Drill the holes according to the drawn holes, making sure that there is no offset of the holes. The wall bracket drilling positions of the left and right walls need to be in alignment and on the same horizontal and vertical plane. The vertical surface of wall bracket drilling position is 1 3/8″ away from exterior vertical surface of your threshold.
   

3. If the guide rail need to be cut to match your shower opening please do it based on actual measurements. If stretch the product installation width please adjusting the insertion. depth of the wall bracket to the guide rail without cutting the guide rail. SS04 has maximum installation width stretch of 1/2″ for each size. Use wire or thin wooden stick to push the base nut into the corresponding hole, then fix the position.
   

4. After the installation of the guide rail, please use the level ruler to measure whether the level. Then install Anti Collision Block on both sides.
   

5. lnstall the glass fixing clips at the top of fixed glass according to the illustration. Fasteners can be slightly adjusted to match glass mounting offsets
   

6. Install the glass bracket at the bottom of fixed glass according to the illustration

7. After the glass installation is completed, please measure the glass with level ruler to confirm the vertical and horizontal of the glass and then install the glass guide block. Ensure the vertical condition of the glass after the guide block is installed. No need to drill hole on the threshold to install guide block
   
   

8. Installation of sliding glass. The height and level of the glass can be adjusted slightly by adjusting the rollers, through this adjustment can be adapted to the shower with a little wall offset, each wall offset preferably not more than 1/4″.
   After the glass installation is completed, please measure the glass with level ruler to confirm the vertical and horizontal of the glass and then install the glass guide block.
   

9. Please follow the guide to install the handle and the bottom rollers. Install the rollers
   under guide rail and adjust its height to fit the bottom of guide rail.
   

10. install the door seal as illustrated, wide door seal should be installed on the fixed glass
    side. The top of wide door seal needs to be lower than the bottom rollers to avoicraping. All door seals should be installed starting from the bottom and working upwards

11. stall the anti-splash threshold according to the guidelines, please cut to the right size according to the width of your shower opening. Clean up the garbage and dry the water and stains with a soft cloth after installation, then applying the glass glue.
    

Note : Please dry for 24 hours after the glass glue is applied before use.

SAFETY TIPS:

1. Do not remove the slide glass protection corners during installation, remove them only after installation is complete.
2. Wear protective equipment when drilling, cutting guide rail and anti-splash threshold.
3. Careful installation of the glass is required during installation, please do not step on the glass to avoid bumping.
4. Wait 24 hours after installation before using the shower.

SHOWER DOOR MAINTENANCE AND CARE:

1. Shower door glass is double-sided easy-clean glass. For daily cleaning using moist soft cloth to wipe away surface water and stains, reduce the use of cleaning agents to extend the easy-clean performance. It’s recommended to use soft cloth to clean the residual water stains on the glass and hardware after shower. Silicone squeegee is available.

2. Do not use any sharp cleaning tools or cleaning agents with abrasive ingredients to clean the glass.

3. Caustic cleaners should not be used, such as alcohol. Long-term
   use of corrosive cleaners will cause discoloration of the hardware. Reducing the use of cleaners will prolong the use of the hardware&glass appearance. You can use small amount of anhydrous ethanol or detergent to clean stubborn water stains or calculus on the hardware.

4. Do not let the shower water directly wash the bottom of slide door.

TROUBLESHOOTING GUIDE AND NOTE

Shower doors don’t close tightly issues:

Q1: When | close the door, the door closes then backs out and never closes

tight. How should | do?

A1: First please check that the anti collision block is installed on both sides, it will hold the glass in place when closing the door to keep it closed. Then use a level to check your guide rail and glass level status, if not installed level, you can adjust the top roller to adjust the sliding glass level and height. Even if your guide rail is a little tilted, the anti collision block will help to complete the closing action and hold the sliding glass, if guide rail is tilted severely, you may need to re-drill.

Shower door leaking issues:

Q1: The bottom of the inner door leaks, how should | do?

AT: Please confirm product wall bracket punching data are correct and the anti-splash threshold glue seals well without leaking, then following adjustment steps need to be made. 1. Adjust the angle of the shower head, avoid the shower water directly wash the bottom of the slide door. 2. Please adjust the height of the top roller to reduce the height of the glass. Complete these 2 steps would solve it, if there still leak please contact customer service for support.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>