Arachnid E800FS1010-A Arcade Style Cabinet Instruction Manual
- June 17, 2024
- Arachnid
Table of Contents
Arcade Style Electronic Dartboard
www.escaladesports.com
E800FS1010-A Arcade Style Cabinet
TO ORDER PARTS
Visit our website before returning to store
WARNING
This is not a toy and is intended for use by or under the supervision of
adults. Darts should only be thrown at the dart board. Ensure the flight path
is clear of people or pets when playing this game. Impact from darts could
cause physical harm, injury or property damage. Don’t throw damaged darts.
Please have your model number when inquiring about parts.
When contacting Escalade Sports please provide your model number, date code
(if applicable), and part number if requesting a replacement part. These
numbers are located on the product, packaging, and in this owner manual.
Your Model Number: E800FS101
Date Code: CPSIA#2-E800FS1010-__MW.
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT NOTES
- Make sure you have all the necessary parts before beginning each assembly step.
- Perform the assembly steps exactly as written to avoid errors,
- Refer to diagrams to aid in the assembly process,
- Keep your original receipt and instruction manuals for the cabinet and electronic dartboard for warranty purposes.
- This is a2 adult assembly
Tools Needed
– Phillips Screwdriver
PREPARATIONS
- Find an open area onthe floor to perform the assembly, inclose proximity to where you plan to put the finished product.
- Carefully open the box, Do not use a knife as you may scratch the cabinet.
- Remove the inner box holding the electronic dartboard and put it to the side until you are ready to install it into the cabinet.
- Take the cabinet and hardware parts out of the box and make sure all of the parts are accounted for.
- Begin assembly.
WARNING!
TIP OVER HAZARD
Do NOT lean onorclimb on this cabinet.
Hand pressure must be applied to the dartboard while removing darts from the
dartboard.
A Safety L-Bracket / Screws / and installation Instructions are included and
must be installed correctly in order to prevent this tip over hazard.
PLEASE KEEP YOURINSTRUCTIONS!
- Your Model number is necessary should you need to contact us.
- Please read through this instruction book to familiarize yourself with all the parts and assembly steps.
- Referto the Parts Identifier and verify that all parts have been included.
- For questions that may arise or for missing parts,
PLEASE CONTACT US BEFORE RETURNING THE PRODUCT TO THE STORE
CONTACT INFORMATION:
Hours: Mon.- Fri., 9:00 am to 5:00 pm EST
Replacement Parts: order online at
www.escaladesports.com
Technical Support:
customerservice@escaladesports.com
/1-800-526-0451
Hardware Identifier (To Scale)
Parts Identifier (Not to Scale)
-
Attach Parts N and L to Part J using Phillips Flat Head Bolts (H1 ). See Figure 1. Factory Installed Inserts on Part N and Part J must be aligned to screw holes for proper attachment. See Figure 1A. Make sure grooves on all parts are aligned. Tighten, but do Not over tighten or strip out H1 Bolts.
PARTS REQUIRED:
H1 Phillips Flat Head Bolt – 4 pcs
J Upper Left Side Panel – 1 pc
N Upper Panel – 1 pc
L Upper Section Bottom Panel – 1 pc Phillips Screwdriver -
Screw Allen Head Bolts (HS) into Factory Installed Inserts on Parts M. Finger tighten Only.
-
Attach Parts M to Part J using Phillips Head Bolts (H1) and Wood Dowel Pins (H4). See Figure 2. Tighten, but do Not over tighten or strip out H1 Bolts.
PARTS REQUIRED:
H1 Phillips Flat Head Bolt – 2 pcs
H4 Wood Dowel Pin – 2 pcs
HS Allen Head Bolt – 2 pcs
M Dartboard Anchor Panel – 2 pcs Phillips Screwdriver -
Important Note: This step requires help from another adult. Hang Dartboard (Q) on Parts M.
-
Important Note: This step requires help from another adult.
Slide Part R into grooves on Parts N, Land J and over Dartboard until board shows through cut out piece.
PARTS REQUIRED:
Q Dartboard – 1 pc
R Front Baffle Panel – 1 pc -
Attach Part K to partially assembled Upper Cabinet using Phillips Flat Head Bolts (H1) and Wood Dowel Pins (H4). See Figure 4. Tighten, but do Not over tighten or strip out H1 Bolts.
PARTS REQUIRED:
H1 Phillips Flat Head Bolt – 6 pcs
H4 Wood Dowel Pin – 2 pcs
K Upper Right Side Panel – 1 pc Phillips Screwdriver -
Screw 4 pcs Panel Bolts (H2) nto Factory Installed Inserts on Part P. Tighten, but do NOT over tighten or strip out H2 Bolts.
-
Insert 4 pcs Panel Bolt Locks (H3) into holes on Parts J and K. Make sure the opening on the Panel Bolt Locks (H3) points upward. See Figure SA
-
Attach Part P to Parts J and K. Tighten Panel Bolt Locks (H3) with a Phillips Screwdriver. See Figure SB.
PARTS REQUIRED:
H2 Panel Bolt – 4 pcs
H3 Panel Bolt Lock – 4 pcs
P Upper Section Arched Front Panel – 1 pc Phillips Screwdriver
Note: Part P must set down flush against Parts J and K before tightening H3 Bolts Lock -
Attach Part S to back of assembled Upper Cabinet using Phillips Round Head Screw (H9). See Figure 6 Tighten, but do Not over tighten or strip out H9 Screws.
PARTS REQUIRED:
H9 Phillips Round Head Screw – 16 pcs
S Upper Back Panel – 1 pcs Phillips Screwdriver -
Attach Parts C to Part A using 4 pcs Phillips Flat Head Bolt (H1 ). See Figure 7. Tighten, but do Not over tighten or strip out H1 Bolts.
-
Insert Wood Dowel Pins (H4) into pre-drilled holes on Parts D. Attach Parts D to Part A. See Figure 7.
PARTS REQUIRED:
H1 Philips Flat Head Bolt – 4 pcs
H4 Wood Dowel Pin – 4 pcs
A Lower Left Side Panel – 1 pc
C Top & Bottom Shelves – 2 pcs
D Middle Shelves – 2 pcs Phillips Screwdriver -
Install 4 pcs Wood Dowel Pins (H4) into Part E. Attach Part E to A. See Figure 8.
-
Install 4 pcs Wood Dowel Pins (H4) into 2 pcs Part D.
-
Attach Part B to partially assembled Lower Cabinet using 4 pcs Phillips Flat Head Bolts (H1) to secure t to 2 pcs Part C.
Important Note: Do NOT tighten H1 Bolts at this time. -
Attach Part T to Lower Cabinet using 2 pcs Pivot Pins (H7).
-
Fully tighten but do Not over tighten or strip out H1 Bolts.
PARTS REQUIRED:
H1 Phillips Flat Head Bolt – 4 pcs
H4 Wood Dowel Pin – 8 pcs
H7 Pivot Pins – 2 pcs
B Lower Right Side Panel – 1 pc
E Base Cross Panel – 1 pc
T Tilt-Down Door Panel – 1 pc Phillips Screwdriver
Important note:
This step requires help from another adult. -
Attach Door Magnet (H10) to Part B using Phillips Round Head Screws (H9). See Figure 9.
-
Attach Door Magnet Attachment (H11) to Part G using 2 pcs Phillips Flat Head Screw (H12).
-
Attach 3 pcs Door Hinges (H8) to Part G using 6 pcs Phillips Round Head Screws (H9) and 3 pcs Phillips Flat Head Screws (H12), See Figure 9A,
-
Note: With help from another adult, attach Part G to Part A using 6 pcs Phillips Round Head Screws (H9) for each hinges. See Figure 9A.
Note: Tighten all screws, but do Not over tighten or strip the screws,
PARTS REQUIRED:
H8 Door Hinge – 3 pcs
H9 Phillips Round Head Screws – 14 pcs
H10 Door Magnet -1 pc
H11 Door Magnet Attachment- 1 pc
H12 Phillips Flat Head Screw = 5 pcs
G Door Panel – 1 pc Phillips Screwdriver -
Note: with help from another adult.
Attach Upper Cabinet Assembly to Lower Cabinet Assembly using 4 pcs Allen Head Bolts (H13), 4 pcs Flat Washer (H14) and 4 pcs Phillips Flat Head Bolts (H1)
See Figure 10. Tighten, but do Not over tighten or strip our H14 & H1 Bolts.
PARTS REQUIRED·:
H1 Phillips Flat Head Bolt – 4 pcs
H13 Allen Head Bolt – 4 pcs
H14 – Flat Washer – 4 pcs Phillips Screwdriver -
Plug in the AC adapter to the back of dartboard and pull through Adapter Hole in Part 5. See Figure 11.
-
Note: with help from another adult.
Stand up assembled cabinet. Attach Part F to back of Lower Cabinet Assembly using 26 pcs Phillips Round Head Screw (H9). See Figure 11.
PARTS REQUIRED:
H9 Phillips Round Head Screw – 26 pcs
F Lower Back Cover – 1 pc Phillips Screwdriver
PRODUCT PART LIST
E800FS1010
Ref | Part# | Description | Qty |
---|---|---|---|
A | E800FS1010-A | Lower Left Side Panel | 1 |
B | E800FS1010-B | Lowe Right Side Panel | 1 |
C | E800FS1010-C | Top & Bottom Shelves | 2 |
D | E800FS1010-D | Middle Shelves | 2 |
E | E800FS1010-E | Base Cross Panel | 1 |
F | E800FS1010-F | Lower Back Cover | 1 |
G | E800FS1010-G | Door Panel | 1 |
J | E800FS1010-J | Upper Left Side Panel | 1 |
K | E800FS1010-K | Upper Right Side Panel | 1 |
L | E800FS1010-L | Upper Section Bottom Panel | 1 |
M | E800FS1010-M | Dartboard Anchor Panel | 2 |
N | E800FS1010-N | Upper Panel | 1 |
P | E800FS1010-P | Upper Section Arched Front Panel | 1 |
Q | E800FS1010-Q | Dartboard | 1 |
R | E800FS1010-R | Front Baffle Panel | 1 |
S | E800FS1010-S | Upper Back Cover | 1 |
T | E800FS1010-T | Tilt-Down Door Panel | 1 |
H1 | E800FS1010-H1 | 40 x 5mm – Phillips Flat Head Bolt | 24 |
H2 | E800FS1010-H2 | 25 x 6mm – Panel Bolt | 4 |
H3 | E800FS1010-H3 | Panel Bolt Lock | 4 |
H4 | E800FS1010-H4 | 20 x 6mm – Wood Dowel Pin | 16 |
H5 | E800FS1010-H5 | 18 x 6mm – Allen Head Bolt | 2 |
H7 | E800FS1010-H7 | 16 x 5mm – Pivot Pin | 2 |
H8 | E800FS1010-H8 | Door Hinge | 3 |
H9 | E800FS1010-H9 | 10 x 3.5mm – Phillips Round Head Screw | 56 |
H10 | E800FS1010-H10 | Door Magnet | 1 |
H11 | E800FS1010-H11 | Door Magnet Attachment | 1 |
H12 | E800FS1010-H12 | 10 x 3.5mm – Phillips Flat Head Screw | 5 |
H13 | E800FS1010-H13 | 25 x 8mm – Allen Head Bolt | 4 |
H14 | E800FS1010-H14 | 8 x 19mm – Flat Washer | 4 |
H15 | E800FS1010-H15 | Allen Wrench | 1 |
H16 | E800FS1010-H16 | Hardware Kit | 1 |
LIMITED WARRANTY
Escalade®Sports (the Company) warrants the Product to be free from defects in
workmanship and materials under normal use and conditions FOR A PERIOD OF 90
DAYS FROM THE DATE OF ORIGINAL PURCHASE in the United States and Canada.
Product Registration Card
The Product Registration Card must be filled out completely and mailed to the
Company at the address printed on the card within 10 days from the date of
your purchase of the Product.
What Is Covered
Except as provided below, this Limited Warranty covers all defects in
materials and workmanship. This Limited Warranty is void if the Product is:
- Damaged through improper usage, negligence, misuse, abuse, transportation damage, acts of nature, or accident (including failure to follow the instructions supplied with the Product)
- Used in commercial applications or rentals
- Modified or repaired by anyone not authorized by the Company
What Is Not Covered
This Limited Warranty does not cover:
- Any expendable items such as batteries, light bulbs, fuses, accessories, cosmetic parts, tools and other items that wear out.
- due to normal usage. Any costs you may incur for delivery, installation, assembly or transport of your product.
What The Company Will Pay For
If during the Limited Warranty period, any part or component of the Product is
found by the Company to be defective, the Company will, at its option, repair
the Product, replace the Product with a new Product (either the same or an
equivalent model) or cause the original retailer of the Product to exchange
the Product with a new Product (either the same or an equivalent model) or
refund the original purchase price of the Product, without charge for labor or
parts. The Company’s obligation to repair, replace or exchange the Product,
however, shall be limited to the amount of the original purchase price of the
Product.
How To Obtain Warranty Service
In order to enforce your rights under this Limited Warranty, you must follow
these procedures:
- You must have completed and mailed the Product Registration Card to the Company within 10 days of purchase of the Product.
- You must include THE ORIGINAL COPY OF YOUR SALES RECEIPT.
- You must call the Company’s Consumer Service Department at 1 – 800 – 526 – 0451 from 9:00 A.M. to 5:00 P.M. (EST) to notify the Company of the nature of the problem.
- If you are instructed to return the Product to the Company for servicing, you are responsible for shipping the Product, at your expense, to the address designated by the Company in packaging that will protect against further damage.
- You must also include your name, address, daytime telephone number, model number of the Product and a description of the problem.
THIS LIMITED WARRANTY IS AVAILABLE ONLY TO THE ORIGINAL PURCHASER OF THE
PRODUCT AND IS VALID IN THE UNITED STATES AND CANADA ONLY.
THE COMPANY’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS
OPTION, OF ANY DEFECTIVE PRODUCT AND SHALL NOT INCLUDE ANY LIABILITY FOR
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS OR DO NOT ALLOW FOR EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. TO
THAT EXTENT, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
This Limited Warranty gives you specific legal rights, but you may also have
other rights that vary from state to state.
If you have questions regarding this Limited Warranty or the operation of the
Product, you may call or write us:
Consumer Service Department
817 Maxwell Ave.
Evansville, IN 47711
1-800-526-0451
www.escaladesports.com
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connect ed.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
“CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.”
The ARACHNID trademark is a registered trademark owned by Arachnid 360 LLC
and used by Escalade Sports pursuant to license
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>