VANPOWERS C30 Electric Road Bike User Manual

THE Seine
USER MANUAL

Contacting Vanpowers

Vanpowers Bike USA
Vanpowers Bike Service Center
1120 US-22 BRIDGEWATER TOWNSHIP, NJ 08807, USA
1 800-819-5929
service@vanpowers.bike
www.vanpowers.bike
UK Authorized Representative
HAIWAI CONSULTING LTD
113, Gloucester Place, Fly, London, England, W1U 6JR
haiwaiconsultingltd@gmail.com
07988167885
Mega Power | At Ease

MADE IN CHINA

Dimensions

Let’s get into the bike’s geometry.
Choosing the right size can guarantee safety and comfort when riding your electric bike. Please seek professional help if you are not sure which size fits you well.

Package Contents

Check the entire box and make sure every single part is present.
Please open all the boxes, gently take out the parts, and check all the contents according to the information on Pages 8–9. In the case of any missing or damaged parts, please contact Vanpowers Bike Service Center.

Accessories Box

| |
---|---|---
Bell| Pedals| Charger
| |
Front Reflector| Rear Reflector| Cable Ties
|
---|---
0.12-inch (3 mm) Allen Key| 0.12-inch (3 mm) Allen Key
|
0.16-inch (4 mm) Allen Key| 0.2-inch (5 mm) Allen Key
|
0.24-inch (6 mm) Long Allen Key| 0.32-inch (8 mm) Long Allen Key
|
8-10 open-end Wrench| 13-15 open-end Wrench
|
Phillips Screwdriver|

Assembly Guide

STEP 1: Mount the front fender

1. Remove the bolts on the fork with 4 mm and 5 mm Allen keys and 8-10 open-end wrench, as shown in Figure 1.
2. Mount the front fender on the fork, then tighten the bolts back, as shown in Figure 2.

STEP 2: Mount the front wheel

1. Remove the quick release lever from in between the forks.
2. Mount the front wheel on the fork, then insert the quick release lever on the same side as the brake rotor, as shown in Figure 3.
3. Tighten the quick release lever clockwise. Adjust the direction of the quick release handle to the position as shown in Figure 4.

Tips:

• Test the tension by opening the lever again. If it is easy to open, tighten the quick release lever further and try again. Make sure the wheel is on securely.
• Do not over-tighten the lever, as this can cause malfunction.

STEP 3: Mount the basket and front light

1. Remove the 4 bolts on the head tube with the 5 mm Allen key, as shown in Figure 5.
2. Mount the basket on the head tube, then tighten the 4 bolts with the 5 mm Allen key, as shown in Figure 6.
3. Remove the bolts on the basket with the 4 mm Allen key, as shown in Figure 7.
4. Take off the front light that is tied on the frame and mount it on the basket with 4 mm Allen key, as shown in Figure 8. Then, tie the light cables to the bottom of the basket with the cable.

STEP 4: Mount the stem and handlebar

1. Remove the bolt on the fork with the 5 mm Allen key, then take off the top cap and alloy- sleeve and discard them, as shown in Figure 9.
2. Mount the stem on top of the fork, then open the clamp on the handlebars by sliding the switch in the direction of the arrow and lifting the latch, as shown in Figure 10.
3. Slide the handlebars onto the stem, angle the handlebars up/down, use the 5 mm Allen key to tighten the stem bolt down inside the tube, as shown in Figure 11.
4. Stand in front of the bike and make sure the handlebars are perpendicular to the two wheels and parallel with the ground, then close the clamp, as shown in Figure 12.
5. Use the 4 mm Allen key to alternately tightenthe 2 bolts on the side of the handlebar stem until fully locked, as shown in Figure 13.

STEP 5: Connect the display

1. Plug the display cable (green) into the display port (green).

STEP 6: Mount the seat/bell/front and rear reflectors

1. Adjust the seat so that it is at a comfortable height, and make sure the seat is pointing towards and perpendicular to the handlebars.
2. Take out the bell/front reflector/rear reflector and Phillips screwdriver from the accessories box. Fix the transparent front reflector and bell to the right of the handlebars.
3. Fix the red rear reflector to the seat post, as shown in Figure 17.

STEP 7: Mount the pedals

1. Check the end cap on both pedals and find the letter L on the left pedal and the letter R on the right pedal.
2. Mount the left pedal on the left crank and tighten counterclockwise with the 15 mm end of a 13-15 open-end wrench. Mount the right pedal on the right crank and tighten clockwise with the 15 mm end of a 13-15 open-end wrench. As shown in Figure 18.

STEP 8: Remove the key
Remove the key from the front of the handlebars and keep it after you finish the assembly.
The key will not affect the use of this electric bicycle; it can only be used when the battery is removed. Please keep it safe.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>