ZUSKE Solar Garden Lights Outdoor User Manual

ZUSKE Solar Garden Lights Outdoor

Product Information

Specifications:

• Solar panel: 1.3W/5.5V
• Battery: 1200mAh/3.7v x 1pcs
• LED Quantity: 15Pcs+1Pcs Spare Bulb
• Filaments Quantity: 15Pcs+1Pcs Spare Filaments
• Length: 31FT
• Working Time: 8 hours (Solar Panel), 4 hours (USB Charger 5V 1A)
• Power Consumption: 0.2W
• Waterproof Rating: IP65

Product Usage Instructions

1. Ensure the product is fully charged before first use using either the solar panel or a 5V USB charger. The indicators will turn green when fully charged.
2. Press the switch button on the control box to select the desired light mode from options such as Steady Light, Slow Flash, Quick Flash, Pulsating Light, Breathing Light. 5 Modes Circulate.

Package Contents:

• 1 * Control box (with solar panel)
• 1 * Ground spike
• 1 * 31FT String light (15pcs bulbs and 15pcs filaments)
• 1 * Spare bulbs and filaments
• 3 * Anchors & screws
• 1 * User manual

FAQ:

1. Q: How do I know when the product is fully charged?
   A: The indicators will turn green when the product is fully charged, whether using the solar panel or a 5V USB charger.

2. Q: How do I change the light mode?
   A: Press the switch button on the control box to cycle through the available light modes.

3. Q: What is the waterproof rating of the product?
   A: The product has a waterproof rating of IP65, making it suitable for outdoor use.

4. Q: How long does the product last on a full charge?
   A: The product can last up to 8 hours when charged via the solar panel and up to 4 hours when charged using a 5V USB charger.

5. Q: How can I contact customer support for further assistance?
   A: For any questions or assistance, feel free to contact us via email at EsK-tech@hotmail.com

INTRODUCTION

31FT G40 LED SOLAR STRING LIGHT
Note: Please read this user manual carefully before use and installation.

1. Solar panel
2. Control box
3. Brace
4. Ground spike
5. Indicators
6. USB Type-C Port
7. Switch
8. LED string lights

PACKAGE CONTAINS

• 1 * Control box (with solar panel)
• 1 * Ground spike
• 1 * 31FT String light (15pcs bulbs and 15pcs filaments)
• 1 * Spare bulbs and filaments
• 3 * Anchors & screws
• 1 * User manual

SPECIFICATION

QUALITY ASSURANCE
If you have any questions, please feel free to contact us.
E-mail: EsK-tech@hotmail.com
Importer name: EsK TECHNOLOGY INC
Importer address: 100 N HOWARD ST STER, SPOKANE, WA, 99201, USA

INSTALLATION

1. Connect the ground spike and string lights with the control box.
2. Settle the string lights and secure the control box to where the solar panel can be shined by sunlight on the ground with the spike or on the wall with the screws)
3. Press the Switch button and select the light mode.
4. Single Press: Steady Light
5. Double Press: Slow Flash
6. Triple Press: Quick Flash
7. Quadruple Press: Pulsating Light
8. Fifth Press: Breathing Light
9. Sixth Press: Off

ADVICE

1. Please re-charge the product before the first use via solar panel or a 5V usb charger. Indicators will turn green when fully charged. fig. 1)
2. A usb charger can be used to charge the product on rainy or cloudy days. (fig.2)

ATTENTION

1. Please install the solar panel in a sunny place and ensure mounted firmly.
2. Please keep solar panel facing up when install.
3. Please classify the built-in lithium battery discarded.
4. 1P65 is suitable for daily outdoor use, but not for harsh environments. It is strictly forbidden to soak the product, damage by limited space heating and pressurization is not allowed.

TROUBLESHOOTING

1. The light does not come on at all:
   • Make sure the wall switch and circuit breaker are on.
2. One of the lamps has burned out.
   • Disconnect power to the string light. Remove effected lamp by gently gripping lamp lens and turning in a counter-clockwise direction. Gently pull out the LED filament piece, then replace with the spare LED filament piece included. Push in until fully seated. Only use spare part provided with this string. Replace the lamp lens by inserting over LED filament, then gently turn the lamp in a clockwise direction until fully seated

ATTENTION:

• a) If you replace the filament according to the above steps 1 to 5, and it does not work normally after turning on the power, it may be that you inserted the filament in the wrong direction.
• b) Disconnect power to the string light. Remove the filament and rotate the filament 180° (change the direction of the wires a and b at the top of the filament), then insert it into the socket. Install the bulb and turn on the power to confirm whether it can work normally.

TIPS: If you follow the steps above to replace the filament, but it still does not work after turning on the power, Please feel free to contact us. We will do our best to help you solve the problem.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>